98/00494 Fluidized-bed coal combustion. Part III. Steam power plants with pressurized fluidized-bed boilers

1998 ◽  
Vol 39 (1) ◽  
pp. 42
2015 ◽  
Vol 31 (4) ◽  
pp. 139-150 ◽  
Author(s):  
Alicja Uliasz-Bocheńczyk ◽  
Maciej Mazurkiewicz ◽  
Eugeniusz Mokrzycki

Abstract Limited use of biomass has been observed in recent years. The processes of electricity and heat production in conventional boilers and fluidized bed boilers generate waste – mainly fly ash. This waste is traditionally used in many industries. The most important are: mining, production of building materials (including cement) and road construction. The use of fly ash in underground mining (suspension technology) is a method of fly ash recovery, which is typical for the Polish industry. The amount of fly ash (10 01 02) and waste (10 01 82) including ashes from fluidized bed boilers in the year 2012 amounted to 1,490.7 thousand tons. For many years, fly ashes from hard coal combustion in conventional boilers has also been used in various production technologies of building materials, such as: cement, concrete, building ceramics and lightweight aggregates. The ashes from hard coal combustion in fluidized bed boilers are also used in the production of cement and autoclaved aerated concrete. Due to extensive economic use, commercial power plants started to reclassify fly ash from hard coal combustion, turning waste into a by-product after meeting the requirements of the Act on waste of 14 December 2012. The ashes from the co-combustion of biomass are also used. The utilization of fly ash from lignite combustion, both from conventional boilers and fluidized bed boilers, is a cause of concern, while the total recovery of fly ash from the combustion of hard coal and lignite has decreased in recent years. For this reason, studies on the use of traditional fly ash technologies such as the production of building materials and new fly ash technologies such as the use as sorbents in power generation and wastewater treatment, as well as on binding CO2 through mineral sequestration in the Carbon Capture and Utilization, are being carried out.


2009 ◽  
Vol 289-292 ◽  
pp. 413-420 ◽  
Author(s):  
F.J. Bolívar ◽  
L. Sánchez ◽  
M.P. Hierro ◽  
F.J. Pérez

The development of new power generation plants firing fossil fuel is aiming at achieving higher thermal efficiencies of the energy conversion process. The major factors affecting the efficiency of the conventional steam power plants are the temperature and, to a lesser extent, the pressure of the steam entering the turbine. The increased operating temperature and pressure require new materials that have major oxidation resistance. Due to this problem, in the last years numerous studies have been conducted in order to develop new coatings to enhance the resistance of steels with chromium contents between 9 and 12% wt against steam oxidation in order to allow operation of steam turbines at 650 0C. In this study, Si protective coatings were deposited by CVD-FBR on ferritic steel P-91. These type of coatings have shown to be protective at 650 0C under steam for at least 3000 hours of laboratory steam exposure under atmospheric pressure. Morphology and composition of coatings were characterized by different techniques, such as scanning electron microscopy (SEM), electron probe microanalysis, and X-ray diffraction (XRD). The results show a substantial increase of steam oxidation protection afforded by Si coating by CVD-FBR process.


Author(s):  
Anis Haj Ayed ◽  
Martin Kemper ◽  
Karsten Kusterer ◽  
Hailu Tadesse ◽  
Manfred Wirsum ◽  
...  

Increasing the efficiency of steam power plants is important to reduce their CO2 emissions and can be achieved by increasing steam temperatures beyond 700 °C. Within the present study, the thermal behavior of a steam by-pass valve subject to cyclic operation with 700 °C steam is investigated experimentally and numerically. An innovative numerical approach was applied to predict the valve’s thermal behavior during cyclic operation, which is essential for fatigue life assessment of such a component. Validation of the applied numerical approach has shown good agreement with measurement results, indicating the potential of its application for the valve design process.


1985 ◽  
Vol 107 (3) ◽  
pp. 569-573 ◽  
Author(s):  
C. M. Harman ◽  
S. Loesch

A method for increasing the peak output of steam power plants through use of a low-pressure feedwater storage system is presented. The generalized availability analysis involves only the low-pressure turbine, low-pressure feedwater heaters, and the storage system. With daily cycling and storage charging at near base load conditions, the turnaround efficiency of the energy storage system was found to approach 100 percent. Storage system turnaround efficiency is decreased when the energy is stored during plant part-load operation.


1959 ◽  
Vol 85 (1) ◽  
pp. 81-114
Author(s):  
R. D. Chellis ◽  
E. Ireland

Sign in / Sign up

Export Citation Format

Share Document