Two-Component Design Strategy: TADF-Type Organic Afterglow for Time-Gated Chemodosimeters

2021 ◽  
pp. 134197
Author(s):  
Guangming Wang ◽  
Jiuyang Li ◽  
Xun Li ◽  
Xuepu Wang ◽  
Yan Sun ◽  
...  
2020 ◽  
Vol 128 (11) ◽  
pp. 1703
Author(s):  
М.В. Рогожин ◽  
В.Е. Рогалин ◽  
М.И. Крымский

Based on the previously developed mathematical model of the behavior of the multi-kilowatt laser window with an unstable cavity, the case of a two-component output window is considered. The two-component window consists of a transparent polycrystalline diamond ring and a central opaque area separated by a plastic vacuum gasket. The central opaque area is equipped with a cryoaccumulator to reduce heat load. Numerical calculations of thermomechanical processes are performed for such windows used in high-power CO2 lasers. Mathematical model used for the calculations consists of three parts - thermophysical, mechanical and optical. The advantages of using a two-component design with a cryoaccumulator under the conditions of a gas laser operating in the multi-kilowatt power range are demonstrated. The dependences of the maximum output power, temperature distribution and mechanical stresses versus the thickness of the window are obtained. The optimal conditions providing maximum radiation strength and minimum beam divergence are considered.


2020 ◽  
Vol 8 (32) ◽  
pp. 16609-16615
Author(s):  
Mingrui Guo ◽  
Ling Wang ◽  
Jing Zhan ◽  
Xiuling Jiao ◽  
Dairong Chen ◽  
...  

A general, simple, two-component design of the electrolyser is proposed to replace the traditional three-component design for decoupled water splitting.


2012 ◽  
Vol 466-467 ◽  
pp. 645-649
Author(s):  
Sen Zhang ◽  
Ting Zhong Wang

In order to avoid the flaw including rigid regulations of architecture, strong coupling degree among modules, removal of fault and advanced technology embeding hardly in 3D visual simulation engine, the novel customizable architecture for 3D visual simulation engine platform was proposed. Following simulation theory of the complication system, introduced some simulation models that design standard, expansibility, assembly relation of simulation component resource, development of typical module and component design. Through the models, the rational design strategy of engine was shown clearly. Application developer could customized simulation assembly component flexibly and composed own 3D visual simulation engine generally.


1965 ◽  
Vol 5 ◽  
pp. 109-111
Author(s):  
Frederick R. West

There are certain visual double stars which, when close to a node of their relative orbit, should have enough radial velocity difference (10-20 km/s) that the spectra of the two component stars will appear resolved on high-dispersion spectrograms (5 Å/mm or less) obtainable by use of modern coudé and solar spectrographs on bright stars. Both star images are then recorded simultaneously on the spectrograph slit, so that two stellar components will appear on each spectrogram.


Author(s):  
R.J. Mount ◽  
R.V. Harrison

The sensory end organ of the ear, the organ of Corti, rests on a thin basilar membrane which lies between the bone of the central modiolus and the bony wall of the cochlea. In vivo, the organ of Corti is protected by the bony wall which totally surrounds it. In order to examine the sensory epithelium by scanning electron microscopy it is necessary to dissect away the protective bone and expose the region of interest (Fig. 1). This leaves the fragile organ of Corti susceptible to physical damage during subsequent handling. In our laboratory cochlear specimens, after dissection, are routinely prepared by the O-T- O-T-O technique, critical point dried and then lightly sputter coated with gold. This processing involves considerable specimen handling including several hours on a rotator during which the organ of Corti is at risk of being physically damaged. The following procedure uses low cost, readily available materials to hold the specimen during processing ,preventing physical damage while allowing an unhindered exchange of fluids.Following fixation, the cochlea is dehydrated to 70% ethanol then dissected under ethanol to prevent air drying. The holder is prepared by punching a hole in the flexible snap cap of a Wheaton vial with a paper hole punch. A small amount of two component epoxy putty is well mixed then pushed through the hole in the cap. The putty on the inner cap is formed into a “cup” to hold the specimen (Fig. 2), the putty on the outside is smoothed into a “button” to give good attachment even when the cap is flexed during handling (Fig. 3). The cap is submerged in the 70% ethanol, the bone at the base of the cochlea is seated into the cup and the sides of the cup squeezed with forceps to grip it (Fig.4). Several types of epoxy putty have been tried, most are either soluble in ethanol to some degree or do not set in ethanol. The only putty we find successful is “DUROtm MASTERMENDtm Epoxy Extra Strength Ribbon” (Loctite Corp., Cleveland, Ohio), this is a blue and yellow ribbon which is kneaded to form a green putty, it is available at many hardware stores.


1997 ◽  
Vol 90 (4) ◽  
pp. 679-681
Author(s):  
F. SAIJA ◽  
G. FIUMARA ◽  
P.V. GIAQUINTA

Sign in / Sign up

Export Citation Format

Share Document