The influence of micromechanical properties and reinforcement architecture on the mechanical response of recycled composites

The use of carbon nanofibers (CNFs) in cement systems has received significant interest over the last decade due to their nanoscale reinforcing potential. However, despite many reports on the formation of localized CNF clusters, their effect on the cement paste micromechanical properties and relation to the mechanical response at the macroscopic scale are still not fully understood. In this study, grid nanoindentation coupled with scanning electron microscopy and energy dispersive spectroscopy was used to determine the local elastic indentation modulus and hardness of a portland cement paste containing 0.2% CNFs with sub-micro and microscale CNF clusters. The presence of low stiffness and porous assemblage of phases (modulus of 15–25 GPa) was identified in the cement paste with CNFs and was attributed primarily to the interfacial zone surrounding the CNF clusters. The CNFs favored the formation of higher modulus C–S–H phases (>30 GPa) in the bulk paste at the expense of the lower stiffness C–S–H. Nanoindentation results combined with a microscale–macroscale upscaling homogenization method further revealed an elastic modulus of the CNF clusters in the range from 18 to 21 GPa, indicating that the CNF clusters acted as compliant inclusions relative to the cement paste.

Download Full-text

Comparison of Substructures Between Uniaxial and Biaxial Deformation in 1100-0 Aluminum

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100096989 ◽

1981 ◽

Vol 39 ◽

pp. 52-53

Author(s):

D. L. Rohr ◽

S. S. Hecker

Keyword(s):

Plastic Strain ◽

Cell Walls ◽

Room Temperature ◽

Mechanical Response ◽

Biaxial Tension ◽

Initial Deformation ◽

Uniaxial Deformation ◽

Biaxial Deformation ◽

Stress States ◽

Comprehensive Study

As part of a comprehensive study of microstructural and mechanical response of metals to uniaxial and biaxial deformations, the development of substructure in 1100 A1 has been studied over a range of plastic strain for two stress states.Specimens of 1100 aluminum annealed at 350 C were tested in uniaxial (UT) and balanced biaxial tension (BBT) at room temperature to different strain levels. The biaxial specimens were produced by the in-plane punch stretching technique. Areas of known strain levels were prepared for TEM by lapping followed by jet electropolishing. All specimens were examined in a JEOL 200B run at 150 and 200 kV within 24 to 36 hours after testing.The development of the substructure with deformation is shown in Fig. 1 for both stress states. Initial deformation produces dislocation tangles, which form cell walls by 10% uniaxial deformation, and start to recover to form subgrains by 25%. The results of several hundred measurements of cell/subgrain sizes by a linear intercept technique are presented in Table I.

Download Full-text

Construction of plastic contact deformation maps on ceramics: a case study on aluminum nitride

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100165641 ◽

1996 ◽

Vol 54 ◽

pp. 636-637

Author(s):

D. L. Callahan

Keyword(s):

Plastic Deformation ◽

Aluminum Nitride ◽

Mechanical Response ◽

Three Dimensional ◽

Bright Field Image ◽

Perfectly Plastic ◽

Contrast Analysis ◽

Deformation Patterns

Modern polishing, precision machining and microindentation techniques allow the processing and mechanical characterization of ceramics at nanometric scales and within entirely plastic deformation regimes. The mechanical response of most ceramics to such highly constrained contact is not predictable from macroscopic properties and the microstructural deformation patterns have proven difficult to characterize by the application of any individual technique. In this study, TEM techniques of contrast analysis and CBED are combined with stereographic analysis to construct a three-dimensional microstructure deformation map of the surface of a perfectly plastic microindentation on macroscopically brittle aluminum nitride.The bright field image in Figure 1 shows a lg Vickers microindentation contained within a single AlN grain far from any boundaries. High densities of dislocations are evident, particularly near facet edges but are not individually resolvable. The prominent bend contours also indicate the severity of plastic deformation. Figure 2 is a selected area diffraction pattern covering the entire indentation area.

Download Full-text