scholarly journals Fracture toughness and crack resistance curves for fiber compressive failure mode in polymer composites under high rate loading

2017 ◽  
Vol 182 ◽  
pp. 164-175 ◽  
Author(s):  
P. Kuhn ◽  
G. Catalanotti ◽  
J. Xavier ◽  
P.P. Camanho ◽  
H. Koerber
Keyword(s):  
Fracture Toughness ◽  
Crack Resistance ◽  
Polymer Composites ◽  
Failure Mode ◽  
High Rate ◽  
Compressive Failure ◽  
Resistance Curves ◽  
High Rate Loading ◽  
Crack Resistance Curves

scholarly journals Determination of the crack resistance curve for intralaminar fiber tensile failure mode in polymer composites under high rate loading

2018 ◽  
Vol 204 ◽  
pp. 276-287 ◽  
Author(s):  
P. Kuhn ◽  
G. Catalanotti ◽  
J. Xavier ◽  
M. Ploeckl ◽  
H. Koerber
Keyword(s):  
Crack Resistance ◽  
Polymer Composites ◽  
Failure Mode ◽  
Tensile Failure ◽  
High Rate ◽  
Resistance Curve ◽  
High Rate Loading

scholarly journals Fracture toughness and crack resistance curves of acrylic bone cements

2019 ◽  
Vol 108 (5) ◽  
pp. 1961-1971
Author(s):  
Tobias Ziegler ◽  
Raimund Jaeger
Keyword(s):  
Fracture Toughness ◽  
Crack Resistance ◽  
Bone Cements ◽  
Resistance Curves ◽  
Crack Resistance Curves

scholarly journals The significance of crack-resistance curves to the mixed-mode fracture toughness of human cortical bone

Biomaterials ◽  
2010 ◽  
Vol 31 (20) ◽  
pp. 5297-5305 ◽  
Author(s):  
Elizabeth A. Zimmermann ◽  
Maximilien E. Launey ◽  
Robert O. Ritchie
Keyword(s):  
Fracture Toughness ◽  
Crack Resistance ◽  
Cortical Bone ◽  
Mixed Mode ◽  
Mixed Mode Fracture ◽  
Mode Fracture ◽  
Human Cortical Bone ◽  
Resistance Curves ◽  
Crack Resistance Curves

Crack Resistance Characterization in TiAl Intermetallics with Enhanced Toughness

2017 ◽  
Vol 741 ◽  
pp. 13-18 ◽  
Author(s):  
Ivo Dlouhý ◽  
Luděk Stratil ◽  
Hiroshi Fukutomi ◽  
Makoto Hasegawa
Keyword(s):  
Fracture Toughness ◽  
Crack Resistance ◽  
Equilibrium Diagram ◽  
Lamellar Microstructure ◽  
Controlled Cooling ◽  
Chevron Notch ◽  
Resistance Curves ◽  
Fracture Performance ◽  
Crack Resistance Curves

The paper is focused on the analysis of the role of lamellar microstructure in fracture performance of model TiAl intermetallic compound. Coarse lamellar colonies and, at the same time, fine lamellar morphology were prepared by compressive deformation at 1553 K (region of stable α phase in TiAl equilibrium diagram) followed by controlled cooling to 1473 K (region of α+g phase) with delay on this temperature and then cooling down. The fracture toughness was evaluated by means of chevron notch technique. In addition, because of enhanced toughness, crack resistance curves were obtained by load - unload technique of pre-racked beams, namely in two directions of crack propagation relative to lamellar structure. Extensive development of shear ligament toughening mechanism was observed in fracture surfaces leading to quite good fracture toughness thanks to the heat treatment applied.

Effect of Heat Treatment on Crack-Resistance Curves in a Liquid-Phase-Sintered Alumina

1989 ◽  
Vol 72 (4) ◽  
pp. 677-679 ◽  
Author(s):  
Stephen J. Bennison ◽  
Helen M. Chan ◽  
Brian R. Lawn
Keyword(s):  
Heat Treatment ◽  
Liquid Phase ◽  
Crack Resistance ◽  
Resistance Curves ◽  
Crack Resistance Curves

Measurement of the fracture toughness associated with the longitudinal fibre compressive failure mode of laminated composites

2012 ◽  
Vol 43 (11) ◽  
pp. 1930-1938 ◽  
Author(s):  
M.J. Laffan ◽  
S.T. Pinho ◽  
P. Robinson ◽  
L. Iannucci ◽  
A.J. McMillan
Keyword(s):  
Fracture Toughness ◽  
Failure Mode ◽  
Laminated Composites ◽  
Compressive Failure ◽  
Longitudinal Fibre

Crack-Resistance Curves of Surface Cracks in Alumina

1988 ◽  
Vol 71 (5) ◽  
pp. C-271-C-273 ◽  
Author(s):  
Rolf W. Steinbrech ◽  
Olaf Schmenkel
Keyword(s):  
Crack Resistance ◽  
Surface Cracks ◽  
Resistance Curves ◽  
Crack Resistance Curves
Sign in / Sign up

Export Citation Format

Share Document