impact loading
Recently Published Documents


TOTAL DOCUMENTS

2677
(FIVE YEARS 614)

H-INDEX

68
(FIVE YEARS 11)

2022 ◽  
Vol 252 ◽  
pp. 113736
Author(s):  
Yun Zhou ◽  
Jianbo Yang ◽  
Xianming Luo ◽  
Hyeon-Jong Hwang ◽  
Hui Chen ◽  
...  

Materials ◽  
2022 ◽  
Vol 15 (2) ◽  
pp. 599
Author(s):  
Kamal Amin Chebo ◽  
Yehya Temsah ◽  
Zaher Abou Saleh ◽  
Mohamad Darwich ◽  
Ziad Hamdan

In Lebanon and many other countries where structures are vulnerable to impact loads caused by accidental rock falls due to landslides, specifically bridges with hollow core slab, it is mandatory to develop safe and efficient design procedures to design such types of structures to withstand extreme cases of loading. The structural response of concrete members subjected to low velocity high falling weight raised the interest of researchers in the previous years. The effect of impact due to landslide falling rocks on reinforced concrete (RC) slabs has been investigated by many researchers, while very few studied the effect of impact loading on pre-stressed structures, noting that a recent study was conducted at Beirut Arab University which compared the dynamic behavior of reinforced concrete and post-tensioned slabs under impact loading from a 605 kg impactor freely dropped from a height of 20 m. Hollow core slabs are widely used in bridges and precast structures. Thus, studying their behavior due to such hazards becomes inevitable. This study focuses on these types of slabs. For a better understanding of the behavior, a full scale experimental program consists of testing a single span hollow core slab. The specimen has 6000 mm × 1200 mm × 200 mm dimensions with a 100 mm cast in a place topping slab. Successive free fall drops cases from 14 m height will be investigated on the prescribed slab having a span of 6000 m. This series of impacts will be held by hitting the single span hollow core slab at three different locations: center, edge, and near the support. The data from the testing program were used to assess the structural response in terms of experimental observations, maximum impact and inertia forces, structural damage/failure: type and pattern, acceleration response, and structural design recommendations. This research showed that the hollow core slab has a different dynamic behavior compared to the post tensioned and reinforced concrete slabs mentioned in the literature review section.


Metals ◽  
2022 ◽  
Vol 12 (1) ◽  
pp. 128
Author(s):  
Masatoshi Nishi ◽  
Shigeru Tanaka ◽  
Akihisa Mori ◽  
Matej Vesenjak ◽  
Zoran Ren ◽  
...  

Cellular metals exhibit diverse properties, depending on their geometries and base materials. This study investigated the mechanism of high-pressure generation during the high-velocity impact of unidirectional cellular (UniPore) materials. Cubic UniPore copper samples were mounted on a projectile and subjected to impact loading using a powder gun to induce direct impact of samples. The specimens exhibited a unique phenomenon of high-pressure generation near the pores during compression. We elucidate the mechanism of the high-pressure phenomenon and discuss the pore geometries that contribute to the generation of high pressures.


Materials ◽  
2022 ◽  
Vol 15 (2) ◽  
pp. 441
Author(s):  
Teghreed H. Ibrahim ◽  
Abbas A. Allawi ◽  
Ayman El-Zohairy

The present study experimentally and numerically investigated the impact behavior of composite reinforced concrete (RC) beams with the pultruded I-GFRP and I-steel beams. Eight specimens of two groups were cast in different configurations. The first group consisted of four specimens and was tested under static load to provide reference results for the second group. The four specimens in the second group were tested first under impact loading and then static loading to determine the residual static strengths of the impacted specimens. The test variables considered the type of encased I-section (steel and GFRP), presence of shear connectors, and drop height during impact tests. A mass of 42.5 kg was dropped on the top surface at the mid-span of the tested beams from five different heights: 250, 500, 1000, 1500, and 1900 mm. Moreover, nonlinear Finite Element (FE) models were developed and validated using the experimental data. Static loading was defined as a displacement-controlled loading and the impact loading was modeled as dynamic explicit analysis with different drop velocities. The validated models were used to conduct a parametric study to investigate the effect of the concrete compressive strength on the performance of the composite beams under static and impact loadings. For the composite specimen with steel I-sction, the maximum impact force was 190% greater than the reference specimen NR-I at a drop height of 1900 mm, whereas the maximum impact forces for the specimens composite specimens with GFRP I-sction without and with shear connectors were 19% and 77%, respectively, more significant than the reference beam at the same drop height. The high stiffness for the steel I-beams relative to the GFRP I-beam was the reason for this difference in behavior. The concrete compressive strength was more effective in improving the impact behavior of the composite specimens relative to those without GFRP I-beams.


2022 ◽  
pp. 107472
Author(s):  
Hongzheng Duan ◽  
Yanqing Wu ◽  
Kun Yang ◽  
Wubuliaisan Maimaitituersun ◽  
Ning Wang ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document