Corrosion behavior of an equiatomic CoCrFeMnNi high-entropy alloy compared with 304 stainless steel in sulfuric acid solution

2018 ◽  
Vol 134 ◽  
pp. 131-139 ◽  
Author(s):  
Hong Luo ◽  
Zhiming Li ◽  
Andrea M. Mingers ◽  
Dierk Raabe
Keyword(s):  
Stainless Steel ◽  
Sulfuric Acid ◽  
Acid Solution ◽  
Corrosion Behavior ◽  
Sulfuric Acid Solution ◽  
304 Stainless Steel ◽  
High Entropy Alloy ◽  
High Entropy

Corrosion behavior of CuCrFeNiMn high entropy alloy system in 1 M sulfuric acid solution

2011 ◽  
Vol 63 (9) ◽  
pp. 828-834 ◽  
Author(s):  
B. Ren ◽  
Z. X. Liu ◽  
D. M. Li ◽  
L. Shi ◽  
B. Cai ◽  
...  
Keyword(s):  
Sulfuric Acid ◽  
Acid Solution ◽  
Corrosion Behavior ◽  
Sulfuric Acid Solution ◽  
Alloy System ◽  
High Entropy Alloy ◽  
High Entropy

Pt-Based Catalytic Microcombustor for Micropower Generation

2014 ◽  
Vol 699 ◽  
pp. 635-641
Author(s):  
Nazri Murat Muhamad ◽  
Azman Miskam Muhamad ◽  
Ahmad Mohd Azmier ◽  
Zainal Alimuddin Zainal Alauddin ◽  
Zulfikar Ishak Mohammad
Keyword(s):  
Stainless Steel ◽  
Sulfuric Acid ◽  
Acid Solution ◽  
Sulfuric Acid Solution ◽  
Steel Surface ◽  
Treatment Time ◽  
Platinum Catalyst ◽  
304 Stainless Steel ◽  
Stainless Steel Surface ◽  
Impregnation Method

This paper presents the fabrication and characterization of platinum-based catalytic microcombustor. The platinum catalyst was deposited onto type-304 stainless steel using the wet impregnation method. The stainless steel undergoes controlled conversion coating treatment in sulfuric acid solution to increase the porosity of its surface before the deposition of the platinum catalyst. The scanning electron microscopy result showed that the porosity on the stainless steel surface will depend on the length of treatment time in the sulfuric acid solution. The surface porosity increased as the treatment time increases. The stainless steel surface morphology changed from smooth to ‘cracked-mud’ morphology after treatment in sulfuric acid solution. The treatment time also provide significant effect to the amount of platinum deposited on the stainless steel surface. The energy dispersive x-ray analysis showed that the amount of deposited platinum for 10 seconds of treatment time was 0.68 wt%, whereas those for 20 and 30 seconds were 0.87 wt% and 1.10 wt%, respectively. Liquefied petroleum gas-air combustion result showed that the flame completely submerged inside the microcombustor with a catalyst, whereas portions of flame can be observed at the exhaust for the microcombustor without a catalyst. The minimum air-to-fuel ratios before the combustion blow-out for 10, 20, and 30 seconds of treatment time was 0.5, 0.4, and 0.3 respectively.

EIS study on passive films of AISI 304 stainless steel in oxygenous sulfuric acid solution

2009 ◽  
Vol 41 (6) ◽  
pp. 531-539 ◽  
Author(s):  
Weiya Lai ◽  
Wenzhen Zhao ◽  
Feng Wang ◽  
Chengzhu Qi ◽  
Jun Zhang
Keyword(s):  
Stainless Steel ◽  
Sulfuric Acid ◽  
Acid Solution ◽  
Sulfuric Acid Solution ◽  
Passive Films ◽  
304 Stainless Steel ◽  
Aisi 304 Stainless Steel ◽  
Aisi 304
Sign in / Sign up

Export Citation Format

Share Document