Long-term fatigue analysis of multi-planar tubular joints for jacket-type offshore wind turbine in time domain

2011 ◽  
Vol 33 (6) ◽  
pp. 2002-2014 ◽  
Author(s):  
Wenbin Dong ◽  
Torgeir Moan ◽  
Zhen Gao
Keyword(s):  
Wind Turbine ◽  
Time Domain ◽  
Fatigue Analysis ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Tubular Joints

Calibration of Long-Term Time-Domain Load Generation for Fatigue Life Assessment of Offshore Wind Turbine

2017 ◽  
Author(s):  
Bryan Nelson ◽  
Yann Quéméner ◽  
Tsung-Yueh Lin ◽  
Hsin-Haou Huang ◽  
Chi-Yu Chien
Keyword(s):  
Fatigue Life ◽  
Wind Turbine ◽  
Fatigue Damage ◽  
Time Domain ◽  
Hot Spot ◽  
Life Assessment ◽  
Offshore Wind ◽  
Wind Loads ◽  
Offshore Wind Turbine

This study evaluated, by time-domain simulations, the fatigue life of the jacket support structure of a 3.6 MW wind turbine operating in Fuhai Offshore Wind Farm. The long-term statistical environment was based on a preliminary site survey that served as the basis for a convergence study for an accurate fatigue life evaluation. The wave loads were determined by the Morison equation, executed via the in-house HydroCRest code, and the wind loads on the wind turbine rotor were calculated by an unsteady BEM method. A Finite Element model of the wind turbine was built using Beam elements. However, to reduce the time of computation, the hot spot stress evaluation combined FE-derived Closed-Form expressions of the nominal stresses at the tubular joints and stress concentration factors. Finally, the fatigue damage was assessed using the Rainflow Counting scheme and appropriate SN curves. Based on a preliminary sensitivity study of the fatigue damage prediction, an optimal load setting of 60-min short-term environmental conditions with one-second time steps was selected. After analysis, a sufficient fatigue strength was identified, but further calculations involving more extensive long-term data measurements are required in order to confirm these results. Finally, this study highlighted the sensitivity of the fatigue life to the degree of fluctuation (standard deviation) of the wind loads, as opposed to the mean wind loads, as well as the importance of appropriately orienting the jacket foundations according to prevailing wind and wave conditions.

Coupled Dynamic Analysis for Multi-Unit Floating Offshore Wind Turbine in Maximum Operational and Survival Conditions

2015 ◽  
Author(s):  
H. K. Jang ◽  
H. C. Kim ◽  
M. H. Kim ◽  
K. H. Kim
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Time Domain ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Random Waves ◽  
Mooring Lines ◽  
Floating Offshore Wind Turbine ◽  
Coupled Dynamic Analysis ◽  
Floating Offshore Wind Turbines

Numerical tools for a single floating offshore wind turbine (FOWT) have been developed by a number of researchers, while the investigation of multi-unit floating offshore wind turbines (MUFOWT) has rarely been performed. Recently, a numerical simulator was developed by TAMU to analyze the coupled dynamics of MUFOWT including multi-rotor-floater-mooring coupled effects. In the present study, the behavior of MUFOWT in time domain is described through the comparison of two load cases in maximum operational and survival conditions. A semi-submersible floater with four 2MW wind turbines, moored by eight mooring lines is selected as an example. The combination of irregular random waves, steady currents and dynamic turbulent winds are applied as environmental loads. As a result, the global motion and kinetic responses of the system are assessed in time domain. Kane’s dynamic theory is employed to formulate the global coupled dynamic equation of the whole system. The coupling terms are carefully considered to address the interactions among multiple turbines. This newly developed tool will be helpful in the future to evaluate the performance of MUFOWT under diverse environmental scenarios. In the present study, the aerodynamic interactions among multiple turbines including wake/array effect are not considered due to the complexity and uncertainty.

Long-Term Dynamic Monitoring of an Offshore Wind Turbine

2013 ◽  
pp. 253-267 ◽  
Author(s):  
Christof Devriendt ◽  
Filipe Magalhães ◽  
Mahmoud El Kafafy ◽  
Gert De Sitter ◽  
Álvaro Cunha ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Offshore Wind ◽  
Dynamic Monitoring ◽  
Offshore Wind Turbine

A Comparison of Time Domain Seismic Analysis Methods for Offshore Wind Turbine Structures: Using a Superelement Approach

2019 ◽  
Author(s):  
Laurens Alblas ◽  
Corine de Winter
Keyword(s):  
Rigid Body ◽  
Wind Turbine ◽  
Time Domain ◽  
Wind Farm ◽  
Assessment Tool ◽  
Seismic Analysis ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Rigid Body Motions ◽  
Seismic Accelerations

Abstract Recently, wind farm development has gained more traction in Asian countries such as Taiwan, which are seismically active. Compared to Europe, the offshore wind structures need to be designed for these additional extreme environmental conditions. For monopiles, these calculations can typically be performed in an integrated way in the wind turbine load calculation, but for jackets the superelement (SE) approach remains preferred. At the time of writing different approaches are being applied in the industry to apply the SE approach for seismic time domain analysis. This work explains and compares three different methods, based on calculations performed in offshore strength assessment tool Sesam and aeroelastic tool BHawC. When including additional interface nodes at the foundation model bottom into the SE to which the seismic accelerations can be applied in BHawC similarly as in the re-tracking run in Sesam, the results between BHawC and Sesam are nearidentical. Using a normal SE, which only includes an interface node for the connection to the wind turbine tower bottom, and including the response due to seismic displacements into the SE load file gives a match between BHawC and Sesam, and closely matches the results of the case with additional interface nodes. Doing the same but only including the dynamic response of the interface point relative to a frame of reference moving with the rigid body motions as caused by the seismic accelerations into the SE load file, significant differences occur. This is due to the lack of the loading effect of rigid body motions. The same conclusions on how these methods compare can be drawn when using different wind and wave cases. The presented results give insights into the differences between the methods and how the choice of method may influence the results.

On the Modeling of Nonlinear Waves for Prediction of Long-Term Offshore Wind Turbine Loads

2008 ◽  
Author(s):  
P. Agarwal ◽  
L. Manuel
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Return Period ◽  
Wave Model ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Offshore Wind Turbines ◽  
Irregular Wave ◽  
Inflow Turbulence

In the design of wind turbines—onshore or offshore—the prediction of extreme loads associated with a target return period requires statistical extrapolation from available loads data. The data required for such extrapolation are obtained by stochastic time-domain simulation of the inflow turbulence, the incident waves, and the turbine response. Prediction of accurate loads depends on assumptions made in the simulation models employed. While for the wind, inflow turbulence models are relatively well established, for wave input, the current practice is to model irregular (random) waves using a linear wave theory. Such a wave model does not adequately represent waves in shallow waters where most offshore wind turbines are being sited. As an alternative to this less realistic wave model, the present study investigates the use of irregular nonlinear (second-order) waves for estimating loads on an offshore wind turbine, with a focus on the fore-aft tower bending moment at the mudline. We use a 5MW utility-scale wind turbine model for the simulations. Using, first, simpler linear irregular wave modeling assumptions, we establish long-term loads and identify governing environmental conditions (i.e., the wind speed and wave height) that are associated with the 20-year return period load derived using the inverse first-order reliability method. We present the nonlinear irregular wave model next and incorporate it into an integrated wind-wave-response simulation analysis program for offshore wind turbines. We compute turbine loads for the governing environmental conditions identified with the linear model and also for an extreme environmental state. We show that computed loads are generally larger with the nonlinear wave modeling assumptions; this establishes the importance of using such refined nonlinear wave models in stochastic simulation of the response of offshore wind turbines.

Fatigue Analysis for Mooring System of a Spar-Type Floating Offshore Wind Turbine

2020 ◽  
Author(s):  
Xutian Xue ◽  
Xiaoyong Liu ◽  
Nian-Zhong Chen ◽  
Xifeng Gao
Keyword(s):  
Wind Turbine ◽  
Fatigue Analysis ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Safety Factors ◽  
Mooring Lines ◽  
Hydrodynamic Analysis ◽  
Floating Offshore Wind Turbine ◽  
Different Diameters ◽  
Rainflow Counting

Abstract This paper aims to perform a time-domain mooring fatigue analysis for a Spar-type floating offshore wind turbine operated in the South China Sea. Tension ranges of mooring lines are achieved from a hydrodynamic analysis where the effects of wind, wave and current are considered. A rainflow counting method is used to calculate the number of mooring tension cycles with corresponding ranges. The fatigue lives of mooring lines are then predicted by Palmgren-Miner’s rule according to T-N & S-N curves. A comparison of fatigue lives predicted by T-N & S-N curves-based approaches with/without considering safety factors is made. The results show that the T-N curves-based approach is more conservative than the S-N curves-based approach if safety factors are not considered in the two approaches, while the fatigue lives predicted by both approaches are in general comparable when the safety factors suggested by API and DNVGL are applied in the two approaches. A comparative study of three kinds of R4 grade studless mooring chains with different diameters (2.5-inch, 4-inch, 5-inch) is also conducted and the results show that the design with the 2.5-inch chain does not meet the fatigue requirements.

Sign in / Sign up

Export Citation Format

Share Document