Assessment of existing two phase heat transfer coefficient and critical heat flux correlations for cryogenic flow boiling in pipe quenching experiments

2016 ◽  
Vol 93 ◽  
pp. 441-463 ◽  
Author(s):  
Jason Hartwig ◽  
Samuel Darr ◽  
Anthony Asencio
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Critical Heat Flux ◽  
Flow Boiling ◽  
Two Phase ◽  
Cryogenic Flow ◽  
Two Phase Heat Transfer

Two-Phase Pipe Quenching Correlations for Liquid Nitrogen and Liquid Hydrogen

2019 ◽  
Vol 141 (4) ◽  
Author(s):  
S. R. Darr ◽  
J. W. Hartwig ◽  
J. Dong ◽  
H. Wang ◽  
A. K. Majumdar ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Liquid Nitrogen ◽  
Critical Heat Flux ◽  
Flow Boiling ◽  
Nucleate Boiling ◽  
Liquid Hydrogen ◽  
Two Phase ◽  
Cryogenic Flow ◽  
Two Phase Heat Transfer

Recently, two-phase cryogenic flow boiling data in liquid nitrogen (LN2) and liquid hydrogen (LH2) were compared to the most popular two-phase correlations, as well as correlations used in two of the most widely used commercially available thermal/fluid design codes in Hartwig et al. (2016, “Assessment of Existing Two Phase Heat Transfer Coefficient and Critical Heat Flux on Cryogenic Flow Boiling Quenching Experiments,” Int. J. Heat Mass Transfer, 93, pp. 441–463). Results uncovered that the correlations performed poorly, with predictions significantly higher than the data. Disparity is primarily due to the fact that most two-phase correlations are based on room temperature fluids, and for the heating configuration, not the quenching configuration. The penalty for such poor predictive tools is higher margin, safety factor, and cost. Before control algorithms for cryogenic transfer systems can be implemented, it is first required to develop a set of low-error, fundamental two-phase heat transfer correlations that match available cryogenic data. This paper presents the background for developing a new set of quenching/chilldown correlations for cryogenic pipe flow on thin, shorter lines, including the results of an exhaustive literature review of 61 sources. New correlations are presented which are based on the consolidated database of 79,915 quenching points for a 1.27 cm diameter line, covering a wide range of inlet subcooling, mass flux, pressure, equilibrium quality, flow direction, and even gravity level. Functional forms are presented for LN2 and LH2 chilldown correlations, including film, transition, and nucleate boiling, critical heat flux, and the Leidenfrost point.

The Effect of Inlet Orifice on Critical Heat Flux and Flow Boiling Heat Transfer in Single Horizontal Microtube

2013 ◽  
Author(s):  
Yanfeng Fan ◽  
Ibrahim Hassan
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Critical Heat Flux ◽  
Boiling Heat Transfer ◽  
Flow Boiling ◽  
Saturation Pressure ◽  
Working Fluid ◽  
Flow Boiling Heat Transfer

Flow oscillation is a crucial issue for the development of flow boiling heat transfer in the applications. Inlet orifice has been proven be an option to eliminate the oscillation. However, the effects of inlet orifice on critical heat flux and flow boiling heat transfer coefficient are lack of study. In this work, the effects of inlet restriction on critical heat flux and heat transfer coefficient in single horizontal microtube under uniform heating condition is experimentally investigated using FC-72 as working fluid. A stainless steel microtube with an inner diameter of 889 μm is selected as main microtube. Two smaller microtubes are assembled at the inlet of main microtube to achieve the restriction configurations of 50% and 20% area ratios. The experimental measurement is carried out at mass fluxes ranging from 160–870 kg/m2·s and heat fluxes varying from 6–170 kW/m2. Two saturation pressures, 10 and 45 kPa, are tested. The experimental results of critical heat flux and two phase heat transfer coefficient obtained in the microtube without orifice are compared with the existing correlations. The addition of an orifice does not enhance the normal critical heat flux but increases the premature critical heat flux. In aspect of heat transfer, the orifice shows improvement on heat transfer coefficient at low mass flux and high saturation pressure.

scholarly journals Evaluation of Heat Transfer Coefficient of Two-Phase Flow Boiling with R290 in Horizontal Mini Channel

2021 ◽  
Vol 88 (3) ◽  
pp. 88-95
Author(s):  
Ronald Akbar ◽  
Jong Taek Oh ◽  
Agus Sunjarianto Pamitran
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Two Phase Flow ◽  
Flow Boiling ◽  
Phase Flow ◽  
Two Phase ◽  
The Heat Transfer Coefficient

Various experiments have been conducted on the heat transfer coefficient of two-phase flow boiling in mini channel tubes. In addition to obtaining data on the heat transfer coefficients through experiments, many researchers have also compared their experimental data using existing correlations. This research aims to determine the characteristics of the heat transfer coefficient of refrigerant R290 from the data used by processing and knowing the best heat transfer coefficient correlation in predicting the experimental data so that the results are expected to be a reference for designing a heat exchanger or for further research. The experimental data predicted is the two-phase flow boiling in a horizontal tube 3 mm diameter, with the mass flux of 50-180 kg/m2s, heat flux of 5-20 kW/m2, saturation temperature of 0-11 °C, and vapor quality of 0-1. The correlation used in this research is based on the asymptotic flow model, where the model is a combination of the nucleate and convective flow boiling mechanisms. The results show an effect of mass flux and heat flux on the experimental heat transfer coefficient and the predicted R290 heat transfer coefficient with asymptotic correlations had a good and similar result to the experimental data.

High Speed Imaging of Bubble Interface Motion in a Tapered Microgap

2020 ◽  
Author(s):  
Aranya Chauhan ◽  
Satish G. Kandlikar
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Critical Heat Flux ◽  
High Speed ◽  
Pool Boiling ◽  
Phase Flow ◽  
Two Phase ◽  
Interface Motion

Abstract The current industrial trend requires development of efficient heat dissipation systems. A tapered microgap on the heater surface provides an efficient pool boiling heat transfer technique in dissipating large heat fluxes. This study is focused on capturing the high-speed images of bubble nucleation, growth and expansion processes. The interface velocities are estimated by tracking the interface of the growing bubble. The insight into interface motion will help in estimating the magnitude of the expanding force and predicting the pressure recovery effect during two-phase flow in the gap. The expansion force helps in establishing high flow rates resulting in high heat transfer coefficient (HTC) and critical heat flux (CHF) values. The effect of design parameters such as taper angle and height of the microgap on the bubble growth patterns are evaluated. The results show that the bubbles are nucleated and are then confined in the narrow gap. The tapered configuration propels the leading bubble interface in the flow direction and eventually the entire bubble in that direction. The bubble motion causes liquid to enter from the narrow region of the microgap. This effect, combined with the pressure recovery resulting from the two-phase flow in the expanding section of the microgap provides a bubble pumping mechanism. This configuration results in improving both the critical heat flux and heat transfer coefficient during pool boiling.

Sign in / Sign up

Export Citation Format

Share Document