High Speed Imaging of Bubble Interface Motion in a Tapered Microgap

2020 ◽  
Author(s):  
Aranya Chauhan ◽  
Satish G. Kandlikar
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Critical Heat Flux ◽  
High Speed ◽  
Pool Boiling ◽  
Phase Flow ◽  
Two Phase ◽  
Interface Motion

Abstract The current industrial trend requires development of efficient heat dissipation systems. A tapered microgap on the heater surface provides an efficient pool boiling heat transfer technique in dissipating large heat fluxes. This study is focused on capturing the high-speed images of bubble nucleation, growth and expansion processes. The interface velocities are estimated by tracking the interface of the growing bubble. The insight into interface motion will help in estimating the magnitude of the expanding force and predicting the pressure recovery effect during two-phase flow in the gap. The expansion force helps in establishing high flow rates resulting in high heat transfer coefficient (HTC) and critical heat flux (CHF) values. The effect of design parameters such as taper angle and height of the microgap on the bubble growth patterns are evaluated. The results show that the bubbles are nucleated and are then confined in the narrow gap. The tapered configuration propels the leading bubble interface in the flow direction and eventually the entire bubble in that direction. The bubble motion causes liquid to enter from the narrow region of the microgap. This effect, combined with the pressure recovery resulting from the two-phase flow in the expanding section of the microgap provides a bubble pumping mechanism. This configuration results in improving both the critical heat flux and heat transfer coefficient during pool boiling.

Pool boiling performance of oxide nanofluid on a downward-facing heating surface

Kerntechnik ◽  
2022 ◽  
Vol 0 (0) ◽  
Author(s):  
Zhibo Zhang ◽  
Huai-En Hsieh ◽  
Yuan Gao ◽  
Shiqi Wang ◽  
Jia Gao ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Surface Roughness ◽  
Stainless Steel ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Critical Heat Flux ◽  
Pool Boiling ◽  
Heating Surface ◽  
Nano Particles

Abstract In this study, the pool boiling performance of oxide nanofluid was investigated, the heating surface is a 5 × 30 mm stainless steel heating surface. Three kinds of nanofluids were selected to explore their critical heat flux (CHF) and heat transfer coefficient (HTC), which were TiO2, SiO2, Al2O3. We observed that these nanofluids enhanced CHF compared to R·O water, and Al2O3 case has the most significant enhancement (up to 66.7%), furthermore, the HTC was also enhanced. The number of bubbles in nanofluid case was relatively less than that in R·O water case, but the bubbles were much larger. The heating surface was characterized and it was found that there were nano-particles deposited, and surface roughness decreased. The wettability also decreased with the increase in CHF.

Impact of Channel Geometry on Two-Phase Flow Heat Transfer Characteristics of Refrigerants in Microchannel Heat Exchangers

1998 ◽  
Vol 120 (2) ◽  
pp. 485-491 ◽  
Author(s):  
T. S. Ravigururajan
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Mass Flux ◽  
Two Phase Flow ◽  
Phase Flow ◽  
Two Phase ◽  
Flow Heat ◽  
The Heat Transfer Coefficient

Microchannel surfaces, often machined to 20 to 1000 μm in width and depth, are employed in high-heat-flux applications. However, a large number of variables, control the two-phase flow heat transfer coefficient. The pressure, the surface heat flux, and the mass flux significantly affect the thermal transport. Experiments were conducted on a setup that was built for testing microchannel heat exchanges. The parameters considered in the study are power input: 20 to 300 W, volume flow rate: 35 to 300 ml/min, quality: 0 to 0.5, inlet subcooling: 5 to 15°C. The results indicate that the heat transfer coefficient and pressure drop are functions of the flow quality, the mass flux, and, of course, the heat flux and the related surface superheat. The heat transfer coefficient decreases from a value of 12,000 W/m2-K to 9000, W/m2-K at 80°C, when the wall superheat is increased from 10 to 80°C. The coefficient decreases by 30 percent when the exit vapor quality is increased from 0.01 to 0.65.

Effect of Particle Morphology on Pool Boiling From Surfaces Coated With Sintered Particles

2015 ◽  
Author(s):  
Suchismita Sarangi ◽  
Justin A. Weibel ◽  
Suresh V. Garimella
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Critical Heat Flux ◽  
Boiling Heat Transfer ◽  
Heat Transfer Performance ◽  
Pool Boiling ◽  
Particle Morphology ◽  
Wall Superheat

Immersion cooling strategies often employ surface enhancements to improve the pool boiling heat transfer performance. Sintered particle/powder coatings with different constituent particle sizes and total layer thicknesses have been commonly used on smooth surfaces to reduce the wall superheat and increase the critical heat flux during pool boiling. However, the role of the particle morphology on pool boiling has not been explicitly investigated. Since the morphology of the particles affects the pore shape, permeability, surface roughness, effective conductivity and diffusivity of the sintered coating, it will impact the heat transfer coefficient and critical heat flux during boiling. In this study, pool boiling of FC-72 is experimentally investigated using copper surfaces coated with a layer of sintered copper particles of irregular, dendritic and spherical morphologies. In order to isolate the effect of particle morphology, particles with the same effective diameter (90–106 μm) are sintered under controlled conditions that yield the same porosity (∼60%) and coating thickness (∼6 particle diameters) for all samples tested. The effects of particle morphology on the incipient wall superheat, nucleate boiling heat transfer coefficient, and critical heat flux are analyzed. The morphology of the pore structure in the coating formed by sintering is observed with SEM images; bubble nucleation and departure characteristics affecting the heat transfer performance of the coatings are qualitatively assessed with the aid of high-speed flow visualizations to corroborate the trends observed in the boiling curves. The irregular particles are observed to show the highest heat transfer coefficient, followed by dendritic and then spherical particles. The critical heat flux is found to be independent of the particle morphology.

scholarly journals Evaluation of Heat Transfer Coefficient of Two-Phase Flow Boiling with R290 in Horizontal Mini Channel

2021 ◽  
Vol 88 (3) ◽  
pp. 88-95
Author(s):  
Ronald Akbar ◽  
Jong Taek Oh ◽  
Agus Sunjarianto Pamitran
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Two Phase Flow ◽  
Flow Boiling ◽  
Phase Flow ◽  
Two Phase ◽  
The Heat Transfer Coefficient

Various experiments have been conducted on the heat transfer coefficient of two-phase flow boiling in mini channel tubes. In addition to obtaining data on the heat transfer coefficients through experiments, many researchers have also compared their experimental data using existing correlations. This research aims to determine the characteristics of the heat transfer coefficient of refrigerant R290 from the data used by processing and knowing the best heat transfer coefficient correlation in predicting the experimental data so that the results are expected to be a reference for designing a heat exchanger or for further research. The experimental data predicted is the two-phase flow boiling in a horizontal tube 3 mm diameter, with the mass flux of 50-180 kg/m2s, heat flux of 5-20 kW/m2, saturation temperature of 0-11 °C, and vapor quality of 0-1. The correlation used in this research is based on the asymptotic flow model, where the model is a combination of the nucleate and convective flow boiling mechanisms. The results show an effect of mass flux and heat flux on the experimental heat transfer coefficient and the predicted R290 heat transfer coefficient with asymptotic correlations had a good and similar result to the experimental data.

The effect of surfactant concentrations and surface material on heat transfer coefficient in nucleate boiling regime

Kerntechnik ◽  
2021 ◽  
Vol 86 (5) ◽  
pp. 365-374
Author(s):  
A. M. Refaey ◽  
S. Elnaggar ◽  
S. H. Abdel-Latif ◽  
A. Hamza
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Boiling Heat Transfer ◽  
Two Phase Flow ◽  
Surfactant Solution ◽  
Nucleate Boiling ◽  
Phase Flow ◽  
Two Phase

Abstract The nucleate boiling regime and two-phase flow are greater importance to the safety analysis of nuclear reactors. In this study, the boiling heat transfer in nuclear reactor is numerical investigated. The computational fluid dynamics (CFD) code, ANSYS Fluent 17.2 is used and the boiling model is employed. The numerical predictions obtained are compared with the experimental data reported by A. Hamza et al. [9]. An experimental test rig is designed and constructed to investigate the effect of cooling water chemistry control and the material of heater surface. CFD software, allows the detailed analysis of the two-phase flow and heat transfer. In this paper, we evaluate the accuracy of the boiling model implemented in the ANSYS Fluent code. This model is based on the heat flux partitioning approach and accommodates the heat flux due to single-phase convection, quenching and evaporation. The validation carried out of surfactant fluid/vapor two-phase flow inside the 2-D cylindrical boiling vessel. A heated horizontal pipe with stainless steel, Aluminum, and Zircalloy surface materials are used to numerically predict the field temperature and void fraction. Different surfactant concentrations ranging from 0, (pure water) to 1500 ppm, and heat fluxes ranging from 31 to 110 kW/m2 are used. The results of the predicted model depict that the addition of SDS Surfactant and increasing the heat flux improves the coefficient of boiling heat transfer for a given concentration. Also, it was found that the increasing of the concentration of aqueous surfactant solution increases the pool boiling heat transfer coefficient. The aqueous surfactant solution SDS improved the heat transfer coefficient of Aluminum, Zircalloy and stainless steel surface materials by 135%.138% and 120% respectively. The results of the numerical model are nearly in agreement with that measured in experimental.

scholarly journals A comprehensive review on pool boiling heat transfer using nanofluids

2019 ◽  
Vol 23 (5 Part B) ◽  
pp. 3209-3237 ◽  
Author(s):  
Asif Khan ◽  
Hafiz Ali
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Critical Heat Flux ◽  
Boiling Heat Transfer ◽  
Pool Boiling ◽  
Research Work ◽  
Research Area ◽  
The Status

Nanofluids are suspensions of nanoparticles with small concentration spread in base fluids such as water, oil and ethylene glycol. Nanofluid boiling is an important research area which provides many chances to explore new frontiers but also poses great challenges. Over the last decade, various studies have been carried out on pool boiling of nanofluids for the enhancement of critical heat flux which is otherwise limited by the use of base fluids. Several efforts have been made in the literature on nanofluid boiling, however, data on the boiling heat transfer coefficient and the critical heat flux have been unpredictable. Current study is a review of the status of research work on effects of nanofluids on heat transfer coefficient and critical heat flux. An emphasis is put in a review form on the recent progresses in nanofluid heat transfer coefficient and critical heat flux of pool boiling. This study also focuses on advancements in nanofluids, their properties and various parameters affecting boiling critical heat flux and heat transfer coefficient. At the end correlations used by different researchers to find out the critical heat flux and heat transfer coefficient are listed.

Sign in / Sign up

Export Citation Format

Share Document