Effect of catalyst layer with zeolite on the performance of a proton exchange membrane fuel cell operated under low-humidity conditions

2021 ◽  
Author(s):  
Ankit Kumar ◽  
Hsiao-Chun Su ◽  
Yong-Song Chen ◽  
Amornchai Arpornwichanop
Keyword(s):  
Fuel Cell ◽  
Proton Exchange Membrane ◽  
Catalyst Layer ◽  
Proton Exchange ◽  
Low Humidity ◽  
Exchange Membrane

scholarly journals Modifying the Catalyst Layer Using Polyvinyl Alcohol for the Performance Improvement of Proton Exchange Membrane Fuel Cells under Low Humidity Operations

Polymers ◽  
2020 ◽  
Vol 12 (9) ◽  
pp. 1865 ◽  
Author(s):  
Prathak Jienkulsawad ◽  
Yong-Song Chen ◽  
Amornchai Arpornwichanop
Keyword(s):  
Fuel Cell ◽  
Polyvinyl Alcohol ◽  
Proton Exchange Membrane ◽  
Catalyst Layer ◽  
Gas Diffusion ◽  
Proton Exchange ◽  
Membrane Electrode ◽  
Power Sources ◽  
Low Humidity ◽  
Exchange Membrane

A proton exchange membrane fuel cell (PEMFC) system for the application of unmanned aerial vehicles is equipped without humidifiers and the cathode channels of the stack are open to the environment due to limited weight available for power sources. As a result, the PEMFC is operated under low humidity conditions, causing membrane dehydration, low performance, and degradation. To keep the generated water within the fuel cell to humidify the membrane, in this study, polyvinyl alcohol (PVA) is employed in the fabrication of membrane electrode assemblies (MEAs). The effect of PVA content, either sprayed on the gas diffusion layer (GDL) or mixed in the catalyst layer (CL), on the MEA performance is compared under various humidity conditions. The results show that MEA performance is increased with the addition of PVA either on the GDL or in the CL, especially for non-humidified anode conditions. The result suggested that 0.03% PVA in the anode CL and 0.1% PVA on the GDL can improve the MEA performance by approximately 30%, under conditions of a non-humidified anode and a room-temperature-humidified cathode. However, MEAs with PVA in the anode CL show better durability than those with PVA on the GDL according to measurement with electrochemical impedance spectroscopy.

Predicting Liquid Water Saturation Through Differently Structured Cathode Gas Diffusion Media of a Proton Exchange Membrane Fuel Cell

2012 ◽  
Vol 9 (2) ◽  
Author(s):  
N. Akhtar ◽  
P. J. A. M. Kerkhof
Keyword(s):  
Fuel Cell ◽  
Liquid Water ◽  
Proton Exchange Membrane ◽  
Water Saturation ◽  
Catalyst Layer ◽  
Gas Diffusion ◽  
Proton Exchange ◽  
Diffusion Media ◽  
Exchange Membrane

The role of gas diffusion media with differently structured properties have been examined with emphasis on the liquid water saturation within the cathode of a proton exchange membrane fuel cell (PEMFC). The cathode electrode consists of a gas diffusion layer (GDL), a micro-porous layer and a catalyst layer (CL). The liquid water saturation profiles have been calculated for varying structural and physical properties, i.e., porosity, permeability, thickness and contact angle for each of these layers. It has been observed that each layer has its own role in determining the liquid water saturation within the CL. Among all the layers, the GDL is the most influential layer that governs the transport phenomena within the PEMFC cathode. Besides, the thickness of the CL also affects the liquid water saturation and it should be carefully controlled.

The Effect of Inlet Parameters on Fluid Flow and Cell Performance at Cathode of a Proton Exchange Membrane Fuel Cell

2010 ◽  
Vol 7 (4) ◽  
Author(s):  
Utku Gulan ◽  
Hasmet Turkoglu ◽  
Irfan Ar
Keyword(s):  
Reynolds Number ◽  
Fuel Cell ◽  
Power Density ◽  
Current Density ◽  
Proton Exchange Membrane ◽  
Catalyst Layer ◽  
Pem Fuel Cell ◽  
Proton Exchange ◽  
Exchange Membrane ◽  
Oxygen Mole Fraction

In this study, the fluid flow and cell performance in cathode side of a proton exchange membrane (PEM) fuel cell were numerically analyzed. The problem domain consists of cathode gas channel, cathode gas diffusion layer, and cathode catalyst layer. The equations governing the motion of air, concentration of oxygen, and electrochemical reactions were numerically solved. A computer program was developed based on control volume method and SIMPLE algorithm. The mathematical model and program developed were tested by comparing the results of numerical simulations with the results from literature. Simulations were performed for different values of inlet Reynolds number and inlet oxygen mole fraction at different operation temperatures. Using the results of these simulations, the effects of these parameters on the flow, oxygen concentration distribution, current density and power density were analyzed. The simulations showed that the oxygen concentration in the catalyst layer increases with increasing Reynolds number and hence the current density and power density of the PEM fuel cell also increases. Analysis of the data obtained from simulations also shows that current density and power density of the PEM fuel cell increases with increasing operation temperature. It is also observed that increasing the inlet oxygen mole fraction increases the current density and power density.

Sign in / Sign up

Export Citation Format

Share Document