The role of hydrogen in the edge dislocation mobility and grain boundary-dislocation interaction in α-Fe

There has been sustained interest over the last few years into both the intrinsic (primary and secondary) structure of grain boundaries and the extrinsic structure e.g. the interaction of matrix dislocations with the boundary. Most of the investigations carried out by electron microscopy have involved only the use of information contained in the transmitted image (bright field, dark field, weak beam etc.). Whilst these imaging modes are appropriate to the cases of relatively coarse intrinsic or extrinsic grain boundary dislocation structures, it is apparent that in principle (and indeed in practice, e.g. (1)-(3)) the diffraction patterns from the boundary can give extra independent information about the fine scale periodic intrinsic structure of the boundary.In this paper I shall describe one investigation into each type of structure using the appropriate method of obtaining the necessary information which has been carried out recently at Tribophysics.

Download Full-text

Strain-induced martensite effects on transgranular carbide precipitation in type 304 stainless steels

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100087331 ◽

1991 ◽

Vol 49 ◽

pp. 604-605

Author(s):

A.H. Advani ◽

L.E. Murr ◽

D. Matlock

Keyword(s):

Heat Treatment ◽

Grain Boundary ◽

Stress Corrosion Cracking ◽

Stainless Steels ◽

Deformation Twin ◽

Austenitic Stainless Steels ◽

Carbide Precipitation ◽

Strain Induced Martensite ◽

Type 304

Thermomechanically induced strain is a key variable producing accelerated carbide precipitation, sensitization and stress corrosion cracking in austenitic stainless steels (SS). Recent work has indicated that higher levels of strain (above 20%) also produce transgranular (TG) carbide precipitation and corrosion simultaneous with the grain boundary phenomenon in 316 SS. Transgranular precipitates were noted to form primarily on deformation twin-fault planes and their intersections in 316 SS.Briant has indicated that TG precipitation in 316 SS is significantly different from 304 SS due to the formation of strain-induced martensite on 304 SS, though an understanding of the role of martensite on the process has not been developed. This study is concerned with evaluating the effects of strain and strain-induced martensite on TG carbide precipitation in 304 SS. The study was performed on samples of a 0.051%C-304 SS deformed to 33% followed by heat treatment at 670°C for 1 h.

Download Full-text

On the role of tin underlays for the prevention of thermal grooving in thin gold films

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100145030 ◽

1986 ◽

Vol 44 ◽

pp. 732-733

Author(s):

Jin Young Kim ◽

R. E. Hummel ◽

R. T. DeHoff

Keyword(s):

Thin Film ◽

Free Surface ◽

Grain Boundary ◽

Beneficial Effect ◽

Failure Mechanism ◽

Failure Mechanisms ◽

Distinct Advantage ◽

Gold Films ◽

Gold Thin Film

Gold thin film metallizations in microelectronic circuits have a distinct advantage over those consisting of aluminum because they are less susceptible to electromigration. When electromigration is no longer the principal failure mechanism, other failure mechanisms caused by d.c. stressing might become important. In gold thin-film metallizations, grain boundary grooving is the principal failure mechanism.Previous studies have shown that grain boundary grooving in gold films can be prevented by an indium underlay between the substrate and gold. The beneficial effect of the In/Au composite film is mainly due to roughening of the surface of the gold films, redistribution of indium on the gold films and formation of In2O3 on the free surface and along the grain boundaries of the gold films during air annealing.

Download Full-text