Effect of Zn Al filler metals on the characteristics of the joint made by the high-frequency induction brazing of 304 stainless steel and 6A02 aluminum

2021 ◽  
Vol 68 ◽  
pp. 961-972
Author(s):  
Haodong Sun ◽  
Gaoyang Yu ◽  
Shuhai Chen ◽  
Jihua Huang ◽  
Jian Yang
Keyword(s):  
Stainless Steel ◽  
High Frequency ◽  
304 Stainless Steel ◽  
Induction Brazing ◽  
High Frequency Induction Brazing ◽  
Filler Metals ◽  
High Frequency Induction

Low-Temperature High-Frequency Induction Brazing of 5052 Aluminum Alloy to Stainless Steel with Sn-Zn Solder

JOM ◽  
2018 ◽  
Vol 71 (5) ◽  
pp. 1785-1792 ◽  
Author(s):  
Gaoyang Yu ◽  
Shuhai Chen ◽  
Lu Hai ◽  
Jihua Huang ◽  
Jian Yang
Keyword(s):  
Stainless Steel ◽  
Aluminum Alloy ◽  
Low Temperature ◽  
High Frequency ◽  
Induction Brazing ◽  
High Frequency Induction Brazing ◽  
High Frequency Induction

Joining Aluminium to Red Copper by High-Frequency Induction Brazing with Argon Shielding

2010 ◽  
Vol 44-47 ◽  
pp. 2539-2542
Author(s):  
Hong Tao Zhang ◽  
Bo Chen ◽  
Ming Zhi Zhai ◽  
Lei Li
Keyword(s):  
High Frequency ◽  
Filler Metal ◽  
Dissimilar Materials ◽  
Compound Layer ◽  
Eutectic Structure ◽  
Intermetallic Compound Layer ◽  
Induction Brazing ◽  
High Frequency Induction Brazing ◽  
Maximum Shear Strength ◽  
High Frequency Induction

Joining Cu to Al has been carried out by high-frequency induction brazing without filler metal. Experimental results showed that the eutectic structure was the main phase of the brazing seams and a regular Cu-Al intermetallic compound layer also appeared near the Cu side. The maximum shear strength of the dissimilar materials joint could be reach 22.5MPa.

Simulation of Temperature Field Induced in Localized Ultra-High Frequency Induction Brazing of Diamond Tools

2012 ◽  
Vol 565 ◽  
pp. 633-638 ◽  
Author(s):  
Qi Lin Li ◽  
Jiu Hua Xu ◽  
Hong Hua Su ◽  
Yu Can Fu
Keyword(s):  
Temperature Field ◽  
High Frequency ◽  
Influence Factors ◽  
Simulation Software ◽  
Ultra High Frequency ◽  
Induction Brazing ◽  
Diamond Tools ◽  
Deformation Problem ◽  
High Frequency Induction Brazing ◽  
High Frequency Induction

Localized ultra-high frequency induction brazing is proposed to deal with the thermal deformation problem of brazed diamond tools. In order to investigate the temperature field distribution, the simulation model of induction brazing for solving the temperature field is described through the FLUX 2D software. The experiment is carried out to verify the numerical simulation result. Good agreement is observed between experimental value and simulation result. The influence factors on temperature field are investigated by the simulation software. Ultra-high frequency induction brazing with diamond grits is carried out based on the conditions given by simulation results. Good bonding between the diamond grits and the filler alloy is observed and the width of the brazed region is less than 3 mm.

Sign in / Sign up

Export Citation Format

Share Document