Grinding Performance Integrated Experimental Evaluation on Alumina Ceramics with Leaf-Vein Bionic Grinding Wheel

In order to enhance the grinding performance of alumina ceramic materials, the surface of the grinding wheels are ablated by laser radiation before grinding, and the three types of leaf-vein bionic grinding wheels with different micro-groove pitches are formed to compare the grinding experiments with normal grinding wheels. The grinding forces and surface roughness were gauged and the morphological characteristics of ground workpiece surfaces were studied. The results showed that with the increase of groove pitch, the normal grinding force was reduced by 9.6-63%, while the tangential grinding force is reduced by 8.3-42%. The groove can promote the flow of coolant, accelerate the heat dissipation and chip removal in the grinding area, reduce the damage of the workpiece and the wear of the grinding wheel, so the vein bionic grinding wheel had more tremendous processing advantages. Among the four kinds of grinding wheels, the leaf-vein bionic grinding wheel with groove pitch equal to 8mm obtained the best grinding effect. The vein-shaped groove had a positive impact on the grinding process.

Research on calculation of grinding surface roughness

In machining processes, grinding is often chosen as the final machining method. Grinding is often chosen as the final machining method. This process has many advantages such as high precision and low surface roughness. It depends on many parameters including grinding parameters, dressing parameters and lubrication conditions. In grinding, the surface roughness of a workpiece has a significant influence on quality of the part. This paper presents a study of the grinding surface roughness predictions of workpieces. Based on the previous studies, the study built a relationship between the abrasive grain tip radius and the Standard marking systems of the grinding wheel for conventional and superabrasive grinding wheels (diamond and CBN abrasive). Based on this, the grinding surface roughness was predicted. The proposed model was verified by comparing the predicted and experimental results. Appling the research results, the surface roughness when grinding three types of steel D3, A295M and SAE 420 with Al2O3 and CBN grinding wheels were predicted. The predicted surface roughness values were close to the experimental values, the average deviation between predictive results and experimental results is 15.11 % for the use of Al2O3 grinding wheels and 24.29 % for the case of using CBN grinding wheels. The results of the comparison between the predicted model and the experiment show that the method of surface roughness presented in this study can be used to predict surface roughness in each specific case. The proposed model was verified by comparing the predicted and measured results of surface hardness. This model can be used to predict the surface hardness when surface grinding

Research on selection of abrasive grain size and cutting parameters when grinding of interrupted surface using aluminum oxide grinding wheel with ceramic binder

In this article, a study on intermittent surface grinding using aluminum oxide grinding wheel with ceramic binder is presented. The testing material is 20XH3A steel (GOST standard – Russian Federation). The testing sample has been sawn 6 grooves, with the width of each groove of 10 mm, the grooves are evenly distributed on the circumference of sample. The testing sample resembles a splined shaft. An experimental matrix of nine experiments has been built by Taguchi method, in which abrasive grain size, workpiece speed, feed rate and depth of cut were selected as input variables. At each experiment, surface roughness (Ra) and roundness error (RE) have been measured. Experimental results show that the aluminum oxide and ceramic binder grinding wheels are perfectly suitable for grinding intermittent surface of 20XH3A steel. Data Envelopment Analysis based Ranking (DEAR) method has been used to solve the multi-objective optimization problem. The results also showed that in order to simultaneously ensure minimum surface roughness and RE, abrasive grain size is 80 mesh, workpiece speed is 910 rpm, feed rate is 0.05 mm/rev and depth of cut is 0.01 mm. If evaluating the grinding process through two criteria including surface roughness and RE, depth of cut is the parameter having the greatest effect on the grinding process, followed by the influence of feed rate, workpiece speed, and abrasive grain is the parameter having the least effect on the grinding process. In addition, the effect of each input parameter on each output parameter has also been analyzed, and orientations for further works have also been recommended in this article

Evaluation of the Relationship Among Dressing Conditions Using Prismatic Dresser, Dressing Resistance, and Grinding Characteristics

In the grinding process, the grinding wheel surface condition changes depending on the dressing conditions, which affects the ground surface roughness and grinding resistance. Several studies have been reported on the practical application of dressing using prismatic dressers in recent years. However, only a few studies that quantitatively evaluate the effects of differences in dressing conditions using prismatic dresser on the ground surface roughness and grinding resistance have been reported. Thus, this study aims to evaluate quantitatively the effect of the difference in dressing conditions using the prismatic dresser on the ground surface roughness and grinding resistance by focusing on the dressing resistance. In the experiment, dressing is performed by changing the dressing lead and the depth of dressing cut with a prismatic dresser, and the ground surface roughness and grinding resistance are measured. Consequently, by increasing the dressing lead and the depth of dressing cut, the ground surface roughness increased, and the grinding resistance decreased. This phenomenon was caused by the increase in dressing resistance when the dressing lead and the depth of dressing cut were increased, which caused a change in the grinding wheel surface condition. Furthermore, the influence of the difference in dressing conditions using the prismatic dresser on the ground surface roughness and grinding resistance can be quantitatively evaluated by using the dressing resistance.

ELID Mirror Surface Grinding for Concave Molds by Conductive Elastic Wheel Containing Carbon Black

Elastic grinding wheels have previously been adopted for the development of the mirror surface finishing method for concave spheres. In this study, new conductive elastic grinding wheels, to which electrolytic in-process dressing (ELID) can be applied, are developed; the aim of the study is to address the challenge of maintaining a constant removal rate for rubber bond wheels. When ELID grinding is performed using a non-diene (isobutane isoprene rubber, IIR)-based wheel, a larger removal amount is achieved, and a higher-quality surface is also achieved compared to a diene (acrylonitrile-butadiene rubber, NBR)-based wheel. In addition, to investigate the effect of grinding wheel bond hardness on the removal amount and ground shape accuracy, grinding wheels with various levels of hardness are prepared by controlling the amount of carbon black contained in them, and grinding experiments are conducted. Thus, a larger removal amount is achieved using a harder grinding wheel, but the roughness of the ground surfaces deteriorates. Therefore, in practice, it is necessary to select an appropriate grinding wheel that can achieve both productivity and surface quality. Finally, to obtain a high-quality mirror finish on a concave spherical surface, ELID grinding is performed on the workpieces as is done for spherical lens molds. Thus, high-quality mirror surfaces with roughness Ra < 10 nm were generated. When the work pieces are ground using a grinding wheel of the same radius, excessive removal occurs at the edge of the concave spherical profile, decreasing the form accuracy. Numerical simulation demonstrates that chamfering of the grinding wheel is effective for improving the shape accuracy. The results of this study are expected to contribute to automation and cost reduction in the mirror-finishing process for concave molds.

Polishing Performance of a Recycled Grinding Wheel Using Grinding Wheel Scraps for the Wet Polishing of Stainless-Steel Sheets

The surfaces of large austenitic stainless-steel sheets, which have side lengths of at least 1 m a sheet thickness of at least 6 mm, used for food tanks and sliding plates in seismic isolation devices, must be finished to a mirror surface. Polishing is performed to improve the surface quality of such sheets and dry machining is typically applied. The problems associated with dry machining are the exhaust heat of machining and treatment of chips. A transition to wet machining is required to solve these problems. In our laboratory, we have developed a wet polishing machine and researched the selection of grinding wheels to develop wet polishing technology for large stainless-steel sheets. In this study, to reduce tool cost and reuse resources, we attempted to manufacture a recycled grinding wheel using snippets of grinding wheel scraps. A polyvinyl alcohol (PVA) aqueous solution was used as the bonding agent for the recycled grinding wheel to reduce environmental load. To overcome the ease of dissolution of PVA in water, we attempted to improve the water resistance of the PVA aqueous solution by incorporating an organic titanium compound. This is one of our efforts to contribute to sustainable development goals. The results are summarized below. (1) A recycled grinding wheel was fabricated by kneading crushed pieces of grinding wheel scrap with a bonding agent. (2) The maintenance of the shape of the recycled grinding wheel was controlled by the concentration of the bonding agent. (3) The recycled grinding wheel with a PVA bonding agent was vulnerable to water. In contrast, the recycled grinding wheel to which the organic titanium compound was added exhibited improved water resistance. (4) The polishing of stainless-steel sheets using the plain PVA recycled wheel was relatively ineffective, but polishing using the recycled wheel with the titanium additive was comparable to polishing with a new grinding wheel.