Microstructure and Fracture Toughness of Nitrided D2 Steels Using Potential-Controlled Nitriding

Potential-controlled nitriding is an effective technique for enhancing the life of steel molds and dies by improving their surface hardness and toughness against fatigue damage. In this study, the effect of the nitriding potential on the microstructure and fracture toughness of nitrided AISI D2 steels was investigated. The nitrided layers were characterized by microhardness measurements, optical microscopy, and scanning electron microscopy, and their phases were identified by X-ray and electron backscatter diffraction. As the nitriding potential increased to 2.0 atm−1/2, an increase in the surface hardness and fracture toughness was observed with the growth of the compound layer. However, both the surface hardness and the fracture toughness decreased at the higher nitriding potential of 5.0 atm−1/2 owing to the increased porosity in the compound layers, which mainly consist of the ε (Fe2–3N) phase. Additionally, by observing crack growth behavior, the fracture toughness was analyzed considering the material characteristics of the diffusion and compound layers. The fracture toughness was influenced by the location of the initial Palmqvist cracks due to the localized plastic deformation of the diffusion layer and increased crack length due to the porous compound layer.

Experimental evaluation and modelling of the boronizing kinetics of AISI H13 hot work tool steel

In the study for this contribution, the AISI H13 hot work steel was pack-boronized between 2 and 6 h of exposure time within the temperature range of 800 – 1000 °C. The boriding agent was composed of a powder mixture containing (in weight percent): 90 % of boron carbide (B4C) and 10 % of sodium tetrafluoroborate (NaBF4). The SEM observations showed a less pronounced jagged interface between the boronized layer and the transient zone. A double phase boride layer (FeB and Fe2B) was identified over the surface of AISI H13 steel with the presence of metallic borides inside this compound layer. The mean diffusion coefficient (MDC) method was applied to analyze the growth of iron borides (FeB and Fe2B) as compact layers over the surfaces of AISI H13 steel. The boron activation energies in the two iron borides were also assessed from the present kinetic approach by assuming the Arrhenius relationships. Afterwards, the kinetic model was checked experimentally by considering two extra boriding conditions (925 °C for 1 and 3 h). Finally, the predicted layer thicknesses are in accordance with experimental measurements.

Influence of Oxygen Admixture on Plasma Nitrocarburizing Process and Monitoring of an Active Screen Plasma Treatment

The effect of a controlled oxygen admixture to a plasma nitrocarburizing process using active screen technology and an active screen made of carbon was investigated to control the carburizing potential within the plasma-assisted process. Laser absorption spectroscopy was used to determine the resulting process gas composition at different levels of oxygen admixture using O2 and CO2, respectively, as well as the long-term trends of the concentration of major reaction products over the duration of a material treatment of ARMCO® iron. The short-term studies of the resulting process gas composition, as a function of oxygen addition to the process feed gases N2 and H2, showed that a stepwise increase in oxygen addition led to the formation of oxygen-containing species, such as CO, CO2, and H2O, and to a significant decrease in the concentrations of hydrocarbons and HCN. Despite increased oxygen concentration within the process gas, no oxygen enrichment was observed in the compound layer of ARMCO® iron; however, the diffusion depth of nitrogen and carbon increased significantly. Increasing the local nitrogen concentration changed the stoichiometry of the ε-Fe3(N,C)1+x phase in the compound layer and opens up additional degrees of freedom for improved process control.

Interaction of N with White-solidified Cast Iron Model Alloys: The Effect of Mn and Cu on the Formation of Fe and Si Nitrides

Surface remelting and subsequent nitriding improves the surface properties of cast irons. Upon remelting, a white-solidified surface layer forms, which contains coarse Si-free eutectic cementite (θ) and Si-enriched ferrite, pearlite or martensite in the intercarbidic regions between the eutectic θ. Nitriding produces a compound layer at the surface, which is composed of ε and γ’-iron (carbo)nitrides and enhances the corrosion resistance. Nitriding of white-solidified Fe-C-Si alloys, being model materials for remelted low-alloy ferritic cast irons, has shown that Si dissolved in α-Fe notably affects the formation of ε and γ’ in intercarbidic regions while Si simultaneously precipitates as amorphous nitride, X. Under process conditions only allowing for the formation of γ’ in pure Fe, Si dissolved in α-Fe promotes the formation of ε over the formation γ’, whereas Si-free eutectic θ transforms into nitride following the sequence θ → ε → γ’. The present work studies the nitriding of white-solidified Fe-3.5wt.%C-3wt.%-M alloys with additions of M = 1 wt.% Mn, 1 wt.% Cu or 1 wt.% Mn + 1 wt.% Cu, serving as model materials for remelted pearlitic cast irons. The presence of Mn and/or Cu causes notable deviations from the nitriding behavior known from Fe-C-Si alloys. Mn accelerates the precipitation of X in intercarbidic regions and obstructs the transformation of ε formed from Si-free θ into γ’. Cu promotes the formation of γ’ in Si-rich intercarbidic regions, surpassing the ε-promoting effect of Si.

Carbonitriding of Forging Dies

Forging dies have to resist high mechanical and thermal loads. Therefore, they are usually nitrided. Former investigations showed that the abrasive wear at the critical parts of the dies is much higher than the nitriding hardness depth. Carbonitriding offers the possibility to increase the hardness depth in shorter treatment times because of the higher treatment temperature. The (carbo-)nitrided surface region obtains a better hardness at elevated temperatures and a better wear resistance than the untreated steel. In order to create a wear- and corrosion-resistant compound layer at the surface, a nitriding process step can be conducted after carbonitriding. The present work deals with developing a carbonitriding treatment for forging dies and investigations on the wear resistance of the created surface zones in model wear tests and tool life time experiments under industrial conditions. The aim of this work was to produce heat- and wear-resistant precipitation layers in hot working tool steels in economical treatment durations.

Optimization of FSP Process Parameters on AA5052 Employing the S/N Ratio and ANOVA Method

AA5052 bead-on-plate processing has been achieved by the friction stir processing (FSP) technique to examine the manipulation of process parameters. It also improved the base metal surfaces to analyze the microstructure. The tool spinning speed, traverse speed, and axial load were preferred to investigate the effect of friction stir bead-on-plate processing on the tensile strength qualities and microhardness in AA5052. An optical microscope was used to dissect the fabricated processed zones of the microstructure. By using the design of the experiment, the orthogonal array of the L9 Taguchi method was used to construct the processing experiments. The analysis of variance and the signal-to-noise ratio methods were employed to identify the optimum unification of process parameters and the significant benefaction of a specific parameter on the responses. The outcomes showed that the tool spinning speed was the principal factor affecting the characteristics of tensile strength and microhardness, succeeded by the traverse speed and axial load. The intermetallic compound layer had formed during the processing under specified conditions. This examination revealed that the optimum parameters could intensify the mechanical behaviour of AA5052.

Nitriding and Ferritic Nitrocarburizing of Quenched and Tempered Steels

A physics-based software model is being developed to predict the nitriding and ferritic nitrocarburizing (FNC) performance of quenched and tempered steels with tempered martensitic microstructure. The microstructure of the nitrided and FNC steels is comprised of a white compound layer of nitrides (ε and γ’) and carbides below the surface with a hardened diffusion zone (i.e., case) that is rich in nitrogen and carbon. The composition of the compound layer is predicted using computational thermodynamics to develop alloy specific nitriding potential KN and carburizing potential KC phase diagrams. The thickness of the compound layer is predicted using parabolic kinetics. The diffusion in the tempered martensite case is modeled using diffusion with a reaction. Diffusion paths are also developed on these potential diagrams. These model predictions are compared with experimental results.