The effect of stemless humeral component fixation feature design on bone stress and strain response: a finite element analysis

In order to solve the cracking and poor reliability problems of motor box of Horizontal Roadheader, the static structural FEA (Finite Element Analysis) of cutting arm & motor box of the EBH160 Horizontal Roadheader was conducted, and the stress and strain contours of FEA were obtained. By comparing the calculated results, the safety factor of cutting arm & motor box was 1.36, which provides a reference for the optimal design of cutting arm & motor box.

Download Full-text

Finite Element Analysis of Stress-Strain Response at the Tool Pin During Friction Stir Process

Procedia Computer Science ◽

10.1016/j.procs.2015.12.330 ◽

2015 ◽

Vol 76 ◽

pp. 522-527

Author(s):

M. Shamil Jaffarullah ◽

Nur’Amirah Busu ◽

Cheng Yee Low ◽

J.B. Saedon ◽

Armansyah ◽

...

Keyword(s):

Finite Element Analysis ◽

Finite Element ◽

Strain Response ◽

Stress Strain ◽

Element Analysis ◽

Friction Stir Process ◽

Friction Stir ◽

Tool Pin

Download Full-text

Finite Element Analysis of Drilling Frame on Down-the-Hole Drill Based on Mechanical Mechanics and Mechanical Properties

Advanced Materials Research ◽

10.4028/www.scientific.net/amr.908.282 ◽

2014 ◽

Vol 908 ◽

pp. 282-286

Author(s):

Wan Rong Wu ◽

Lin Chen

Keyword(s):

Finite Element Analysis ◽

Finite Element ◽

Working Condition ◽

Slenderness Ratio ◽

Stress And Strain ◽

Limit States ◽

Element Analysis ◽

Practical Engineering ◽

Structure Strength ◽

Strength And Stiffness

Drilling frame on TD165CH Down-The-Hole Drill that has large slenderness ratio and be longer than 10m is one component of Down-The-Hole drill which is mainly subjected to load.In the process of drilling, drilling frame is not only subjected to loads which are like tensile, compression and torsion and so on, and be under the influence of impacting and vibration of impactor,the situation of force is complicated.By analysing of working condition of Down-The-Hole drill,there get all kinds of limit states of typical working conditions, and then using Ansys doing finite element analysis, there get distribution of the stress and strain of drilling frame and the result of modal analysis to check whether drilling frame meets the requirements of strength and stiffness or not,and whether it is possible to resonate with the impactor or not.By analysis,Structure strength and stiffness of drilling Frame on TD165CH Down-The-Hole drill meet the requirements of practical engineering, and drilling Frame does not resonate with the impactor.

Download Full-text

Bone stress when miniplates are used for orthodontic anchorage: Finite element analysis

American Journal of Orthodontics and Dentofacial Orthopedics ◽

10.1016/j.ajodo.2012.04.019 ◽

2012 ◽

Vol 142 (4) ◽

pp. 466-472 ◽

Cited By ~ 6

Author(s):

Yen-Wen Huang ◽

Chih-Han Chang ◽

Tung-Yiu Wong ◽

Jia-Kuang Liu

Keyword(s):

Finite Element Analysis ◽

Finite Element ◽

Orthodontic Anchorage ◽

Element Analysis ◽

Bone Stress

Download Full-text

Finite Element Analysis on Rack and Pinion of Roadheader

Advanced Materials Research ◽

10.4028/www.scientific.net/amr.791-793.718 ◽

2013 ◽

Vol 791-793 ◽

pp. 718-721

Author(s):

Man Man Xu ◽

Yu Li ◽

Sai Nan Xie ◽

Qing Hua Chen

Keyword(s):

Finite Element Analysis ◽

Finite Element ◽

Spur Gear ◽

Stress And Strain ◽

Analysis Method ◽

Element Analysis ◽

The Road ◽

The Finite Element Analysis ◽

Gear Rack ◽

Stress And Strain Distribution

To analyse the road-header rack and pinion by using the finite element analysis software COSMOS/WORKS. Compared to the traditional analytic calculation and numerical analysis method, it is more intuitively get 28 ° pressure angle spur gear rack meshing stress and strain distribution, which can rack and pinion improvements designed to provide scientific reference.

Download Full-text