New insight into the membrane fouling of anaerobic membrane bioreactors treating sewage: Physicochemical and biological characterization of cake and gel layers

2021 ◽  
Vol 632 ◽  
pp. 119383
Author(s):  
Zhen Lei ◽  
Jun Wang ◽  
Luwei Leng ◽  
Shuming Yang ◽  
Mawuli Dzakpasu ◽  
...  
Keyword(s):  
Membrane Fouling ◽  
Membrane Bioreactors ◽  
Biological Characterization ◽  
Anaerobic Membrane Bioreactors ◽  
Insight Into

A review on membrane fouling control in anaerobic membrane bioreactors by adding performance enhancers

2021 ◽  
Vol 40 ◽  
pp. 101867
Author(s):  
Weonjung Sohn ◽  
Wenshan Guo ◽  
Huu Hao Ngo ◽  
Lijuan Deng ◽  
Dongle Cheng ◽  
...  
Keyword(s):  
Membrane Fouling ◽  
Membrane Bioreactors ◽  
Fouling Control ◽  
Anaerobic Membrane Bioreactors ◽  
Performance Enhancers

scholarly journals Long-Term Investigation into the Membrane Fouling Behavior in Anaerobic Membrane Bioreactors for Municipal Wastewater Treatment Operated at Two Different Temperatures

Membranes ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 231
Author(s):  
Yi Ding ◽  
Zhansheng Guo ◽  
Zhenlin Liang ◽  
Xuguang Hou ◽  
Zhipeng Li ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Membrane Fouling ◽  
Municipal Wastewater ◽  
Membrane Bioreactors ◽  
Municipal Wastewater Treatment ◽  
Sludge Flocs ◽  
Microbial Product ◽  
Anaerobic Membrane Bioreactors ◽  
Sludge Particle

In this study, the characteristics of activated sludge flocs were investigated and their effects on the evolution of membrane fouling were considered in the anaerobic membrane bioreactors (AnMBR), which were operated at 25 and 35 °C for municipal wastewater treatment. It was found that the membrane fouling rate of the AnMBR at 25 °C was more severe than that at 35 °C. The membrane fouling trends were not consistent with the change in the concentration of soluble microbial product (SMP). The larger amount of SMP in the AnMBR at 35 °C did not induce more severe membrane fouling than that in the AnMBR at 25 °C. However, the polysaccharide and protein concentration of extracellular polymeric substance (EPS) was higher in the AnMBR at 25 °C in comparison with that in the AnMBR at 35 °C, and the protein/polysaccharide ratio of the EPS in the AnMBR at 25 °C was higher in contrast to that in the AnMBR at 35 °C. Meanwhile, the fouling tendencies measured for the AnMBRs could be related to the characteristics of loosely bound EPS and tightly bound EPS. The analysis of the activated sludge flocs characteristics indicated that a smaller sludge particle size and more fine flocs were observed at the AnMBR with 25 °C. Therefore, the membrane fouling potential in the AnMBR could be explained by the characteristics of activated sludge flocs.

Feasibility of submerged anaerobic membrane bioreactor (SAMBR) for treatment of low-strength wastewater

2008 ◽  
Vol 58 (10) ◽  
pp. 1925-1931 ◽  
Author(s):  
Z. Huang ◽  
S. L. Ong ◽  
H. Y. Ng
Keyword(s):  
Membrane Fouling ◽  
Membrane Bioreactors ◽  
Organic Loading Rate ◽  
Effluent Quality ◽  
Significant Difference ◽  
Anaerobic Membrane Bioreactors ◽  
High Purification ◽  
Low Strength ◽  
Set Up ◽  
Internal Pore

Two 6-L submerged anaerobic membrane bioreactors (SAMBR) with SRT of 30 and 60 d (denoted as R30 and R60, respectively) were set up and operated for five months, with a mixture of glucose as substrate. Feasibility of SAMBR was studied for treatment of low-strength wastewater. First two months were identified as acclimation stage. A COD removal efficiency was achieved stably at around 99% and biogas productions were maintained at 0.023 and 0.028 L CH4/gMLVSS∙d for R30 and R60, respectively. Even though R60 contained higher MLVSS concentration, no significant difference of treatment performances between both reactors was found due to the low organic loading rate and high purification function of membrane. In the investigation of membrane fouling, less irreversible fouling was observed for R30 compared to R60. High non-flocculent concentration of R60 would be responsible for membrane internal pore blocking and deteriorated effluent quality.

Fouling cake layer in a submerged anaerobic membrane bioreactor treating saline wastewaters: curse or a blessing?

2011 ◽  
Vol 63 (12) ◽  
pp. 2902-2908 ◽  
Author(s):  
I. Vyrides ◽  
D. C. Stuckey
Keyword(s):  
Membrane Fouling ◽  
Membrane Bioreactor ◽  
Large Fraction ◽  
Membrane Bioreactors ◽  
Extracellular Polysaccharides ◽  
Cake Layer ◽  
Anaerobic Membrane Bioreactors ◽  
Suspended Biomass ◽  
Microbial Products

The treatment of inhibitory (saline) wastewaters is known to produce considerable amounts of soluble microbial products (SMPs), and this has been implicated in membrane fouling; the fate of these SMPs was of considerable interest in this work. This study also investigated the contribution of SMPs to membrane fouling of the; (a) cake layer/biofilm layer, (b) the compounds below the biofilm/cake layer and strongly attached to the surface of the membrane, (c) the compounds in the inner pores of the membrane, and (d) the membrane. It was found that the cake/biofilm layer was the main reason for fouling of the membrane. Interestingly, the bacteria attached to the cake/biofilm layer showed higher biodegradation rates compared with the bacteria in suspension. Moreover, the bacteria attached to the cake layer showed higher amounts of attached extracellular polysaccharides (EPS) compared with the bacteria in suspension, possibly due to accumulation of the released EPS from suspended biomass in the cake/biofilm layer. Molecular weight (MW) analysis of the effluent and reactor bulk showed that the cake layer can retain a large fraction of the SMPs in the reactor and prevent them from being released into the effluent. Hence, while cake layers lead to lower fluxes in submerged anaerobic membrane bioreactors (SAMBRs), and hence higher costs, they can improve the quality of the reactor effluent.

Characterization of dissolved compounds in submerged anaerobic membrane bioreactors (SAMBRs)

2006 ◽  
Vol 81 (12) ◽  
pp. 1894-1904 ◽  
Author(s):  
Sérgio F Aquino ◽  
Alan Y Hu ◽  
Aurangzeb Akram ◽  
David C Stuckey
Keyword(s):  
Membrane Bioreactors ◽  
Anaerobic Membrane Bioreactors

Approaches to membrane fouling control in anaerobic membrane bioreactors

2000 ◽  
Vol 41 (10-11) ◽  
pp. 363-371 ◽  
Author(s):  
K-H. Choo ◽  
I-J. Kang ◽  
S-H. Yoon ◽  
H. Park ◽  
J-H. Kim ◽  
...  
Keyword(s):  
Membrane Fouling ◽  
Ceramic Membrane ◽  
Substantial Improvement ◽  
Membrane Bioreactors ◽  
Polymer Chains ◽  
Polymeric Membrane ◽  
Hydrophilic Modification ◽  
Grafted Polymer ◽  
Fouling Control ◽  
Anaerobic Membrane Bioreactors

Various fouling control methods were investigated for polymeric and ceramic microfiltration membranes in the anaerobic membrane bioreactors where inorganic precipitates and/or fine colloids have been recently known as the most significant foulants: (i) Substantial improvement of flux was achieved by backfeeding of acidic wastewater through the membrane module. The backfeeding mode formed an acidic environment around the membrane pores and thus suppressed struvite formation. (ii) Struvite precipitation was also mitigated when an additional combined dialysis/zeolite unit was attached to the bioreactor. With this combined unit the flux improvement for the ceramic membrane, where struvite had a severer fouling effect, was achieved more significantly than that for the polymeric membrane. (iii) To control the deposition of organics and fine colloids onto the polymeric membrane, powdered activated carbon (PAC) was added into the bioreactor, which gave rise to the reduction of specific cake resistances of biosolids through the sorption and/or coagulation of dissolved and colloidal matter. (iv) The hydrophilic modification of polypropylene (PP) membranes by graft polymerization reduced membrane fouling. Its effectiveness was most substantial at 70% of the degree of grafting, indicating that there was an optimal degree of grafting. This is possibly due to the steric hindrance of grafted polymer chains and the increase in the hydrophilicity of the grafted PP membrane.

Sign in / Sign up

Export Citation Format

Share Document