Effect of shot peening on rolling contact fatigue and lubricant film thickness within mixed lubricated non-conformal rolling/sliding contacts

2011 ◽  
Vol 44 (12) ◽  
pp. 1726-1735 ◽  
Author(s):  
M. Vrbka ◽  
I. Křupka ◽  
P. Svoboda ◽  
P. Šperka ◽  
T. Návrat ◽  
...  
Keyword(s):  
Film Thickness ◽  
Shot Peening ◽  
Rolling Contact Fatigue ◽  
Contact Fatigue ◽  
Lubricant Film ◽  
Rolling Contact ◽  
Lubricant Film Thickness ◽  
Sliding Contacts

Pressure Distribution Within EHD Point Contacts Based on Measured Film Thickness

Tribology ◽  
2006 ◽  
Author(s):  
Radek Poliscuk ◽  
Michal Vaverka ◽  
Martin Vrbka ◽  
Ivan Krupka ◽  
Martin Hartl
Keyword(s):  
Film Thickness ◽  
Numerical Solution ◽  
Pressure Distribution ◽  
Elastic Deformation ◽  
Contact Fatigue ◽  
Lubricant Film ◽  
Rolling Contact ◽  
Lubricant Film Thickness ◽  
Machine Elements ◽  
Lubricated Contact

Surface topography significantly influences the behavior of lubricated contacts between highly loaded machine elements. Most oil- or grease- lubricated machine elements such as gears, rolling bearings, cams and traction drives operate in mixed lubrication conditions and the lubricant film thickness is directly related to the main practical performance parameters such as function, wear, contact fatigue and scuffing. For determination wear and especially contact fatigue, the values and distribution of the pressure in rolling contact are required. The theoretical studies usually involve the numerical solution of pressure and film thickness in the contact, using some physical mathematical model built around the Reynolds equation to describe the flow and the theory of elastic deformation of semi-infinite bodies. Such calculations can be extremely time consuming, especially when lubricant films are very thin and/or contact load very high. This study is aimed at obtaining pressure distribution within lubricated contact from measured film thickness. Lubricant film thickness distribution within the whole concentrated contact is evaluated from chromatic interferograms by thin film colorimetric interferometry. Consequently, an elastic deformation is separated from the film thickness, geometry and mutual approach of the surfaces. Calculation of the pressure distribution is based on inverse elasticity theory. EHD lubricated contact with smooth surfaces of solids was first investigated. Calculated pressure, distributions were compared with data obtained from full numerical solution to check the accuracy. The approach was also applied to surfaces with dents and their influence on distribution of pressure in lubricant film.

Optimized Mapping of Pressure in Lubricated Point Contacts Based on Measured Film Thickness

2007 ◽  
Author(s):  
Radek Polisˇcˇuk ◽  
Michal Vaverka ◽  
Martin Vrbka ◽  
Ivan Krˇupka ◽  
Martin Hartl
Keyword(s):  
Film Thickness ◽  
Numerical Solution ◽  
Point Contact ◽  
Contact Fatigue ◽  
Lubricant Film ◽  
Rolling Contact ◽  
Experimental Film ◽  
Lubricated Contacts ◽  
Practical Performance ◽  
Traction Drives

The surface topography plays significant role in lifetime of highly loaded machine parts with lubricated contacts. Many elements like gears, rolling bearings, cams and traction drives operate in mixed lubrication conditions, where the lubricant film behavior closely implies the main practical performance parameters such as friction wear, contact fatigue and scuffing. For prediction of wear and especially contact fatigue, the values and distribution of the pressure in rolling contact are often required. The usual theoretical approach based on numerical solution of physical-mathematical models built around the Reynolds equation can be extremely time consuming, especially when lubricant films are very thin, and contact load and required resolution very high. This study presents a further refined approach to our previously published experimental method, based on on inverse elasticity theory and fast convolution transformation between the lubricant film thickness map and the pressure distribution within the point contact. The experimental film thickness maps of EHD lubricated contacts with smooth and dented surfaces were processed using colorimetric interferometry and validated using numerical solution, in order to calibrate numerical parameters and to find limits of the new approach.

scholarly journals Rolling Contact Fatigue Life of Case−Hardened Steel Treated by Shot Peenings with Shot Diameters of 0.05 mm and 0.30 mm

2011 ◽  
Vol 86 ◽  
pp. 645-648 ◽  
Author(s):  
Lei Wang ◽  
Guang Liang Liu ◽  
Masanori Seki ◽  
Masahiro Fujii ◽  
Qian Li
Keyword(s):  
Surface Roughness ◽  
Fatigue Life ◽  
Shot Peening ◽  
Fine Particle ◽  
Rolling Contact Fatigue ◽  
Contact Fatigue ◽  
Surface Hardness ◽  
Hardened Steel ◽  
Rolling Contact ◽  
Contact Fatigue Life

In order to investigate the influence of different shot peenings on the rolling contact fatigue life of case−hardened steel, the thrust type rolling contact fatigue test was performed with a ball−on−disk contact tester. In this study, the case−hardened steel disks were treated by the fine particle peening with a shot diameter of 0.05 mm and the normal shot peening with a shot diameter of 0.30 mm. The surface hardness and the surface compressive residual stress of the test disks were increased by these peenings. On the other hand, the surface roughness of the test disks was increased by the normal shot peening, and was decreased by the fine particle peening. The rolling contact fatigue test showed that the rolling contact fatigue life of the test disks was improved by the fine particle peening, and was not improved by the normal shot peening. The rolling contact fatigue life of the test disks became longer as their surface roughness became smaller. Therefore, it follows from this that the fine particle peening, which can provide the increase in surface hardness and the decrease in surface roughness, is good for the increase in the rolling contact fatigue life of case−hardened steel.

scholarly journals Rolling Contact Fatigue Life of Steel Rollers Treated by Cavitation Peening and Shot Peening

2012 ◽  
Vol 6 (6) ◽  
pp. 478-486 ◽  
Author(s):  
Masanori SEKI ◽  
Hitoshi SOYAMA ◽  
Yuji KOBAYASHI ◽  
Daisuke GOWA ◽  
Masahiro FUJII
Keyword(s):  
Fatigue Life ◽  
Shot Peening ◽  
Rolling Contact Fatigue ◽  
Contact Fatigue ◽  
Rolling Contact ◽  
Contact Fatigue Life

An Approach for the Gear Rolling Contact Fatigue Acceleration

2016 ◽  
Vol 138 (3) ◽  
Author(s):  
Sheng Li ◽  
Jeremy J. Wagner
Keyword(s):  
Film Thickness ◽  
Crack Formation ◽  
Crack Nucleation ◽  
Rotational Velocity ◽  
Rolling Contact Fatigue ◽  
Contact Fatigue ◽  
Rolling Contact ◽  
Time Period ◽  
Gear Contact ◽  
Gear Rolling

This study proposes an approach for the acceleration of the experimental gear rolling contact fatigue (RCF) crack formation. By increasing the rotational velocity of a gear pair, the RCF experimental time period is reduced. However, the film thickness is increased to improve the fatigue performance, to counteract which it is proposed to raise the lubricant temperature to reduce the film thickness. A physics-based gear contact fatigue model is used to quantify and offset the effects of the rotational velocity and the lubricant temperature on the crack nucleation.

Sign in / Sign up

Export Citation Format

Share Document