A note on induced stress changes in hydrocarbon and geothermal reservoirs

1998 ◽  
Vol 289 (1-3) ◽  
pp. 117-128 ◽  
Author(s):  
Paul Segall ◽  
Shaun D. Fitzgerald
2000 ◽  
Vol 88 (1) ◽  
pp. 59-64 ◽  
Author(s):  
M. L. Brongersma ◽  
E. Snoeks ◽  
T. van Dillen ◽  
A. Polman

2010 ◽  
Vol 22 (1) ◽  
pp. 23-28 ◽  
Author(s):  
Vallo Tilgar ◽  
Kadri Moks ◽  
Pauli Saag

2020 ◽  
Vol 39 (12) ◽  
pp. 893-900
Author(s):  
Inga Berre ◽  
Ivar Stefansson ◽  
Eirik Keilegavlen

Hydraulic stimulation of geothermal reservoirs in low-permeability basement and crystalline igneous rock can enhance permeability by reactivation and shear dilation of existing fractures. The process is characterized by interaction between fluid flow, deformation, and the fractured structure of the formation. The flow is highly affected by the fracture network, which in turn is deformed because of hydromechanical stress changes caused by the fluid injection. This process-structure interaction is decisive for the outcome of hydraulic stimulation, and, in analysis of governing mechanisms, physics-based modeling has potential to complement field and experimental data. Here, we show how recently developed simulation technology is a valuable tool to understand governing mechanisms of hydromechanical coupled processes and the reactivation and deformation of faults. The methodology fully couples flow in faults and matrix with poroelastic matrix deformation and a contact mechanics model for the faults, including dilation because of slip. Key elements are high aspect ratios of faults and strong nonlinearities in highly coupled governing equations. Example simulations using our open-source software illustrate direct and indirect hydraulic fault reactivation and corresponding permeability enhancement. We investigate the effect of the fault and matrix permeability and the Biot coefficient. A higher matrix permeability leads to more leakage from a permeable fault and thus suppresses reactivation and slip of the fault compared to the case with a lower matrix permeability. If a fault is a barrier to flow, increase of pressure because of the fluid injection results in stabilization of the fault; the situation is opposite if the fault is highly permeable compared to the matrix. For the given setup, lowering the Biot coefficient results in more slip than the base case. While conceptually simple, the examples illustrate the strong hydromechanical couplings and the prospects of physics-based numerical models in investigating the dynamics.


2006 ◽  
Vol 46 (1) ◽  
pp. 89
Author(s):  
M.K. Rahman

The performance of hydraulic fracturing technology has not been so promising for some Australian tight-gas reservoirs. The existence of reverse faulting stress regimes (i.e. the vertical stress is the minimum one) in these reservoirs is found to be one reason among many others. Previous studies have established that the vertical hydraulic fracture initiated from a vertical well in a reverse faulting stress regime severely turns and twists to become horizontal while fracturing fluid is injected for further propagation of the fracture. This severely turned and twisted fracture impedes the fluid and proppant (engineered sand grains) injection and thus the fracturing job results in a short and constricted fracture. This is considered to be one of the major reasons for premature screen-outs that occur at extremely high-pressure on many occasions in the field, and the subsequent disappointingly low production rates. The aim of this paper is to present the results of an investigation with a model-scale gas reservoir to avoid this problem by carrying out the fracture treatments in a number of stages with production intervals. The basic mechanism that would allow the growth of a long, planar, productive fracture in such a manner is the production-induced stress change around the fracture tip. A simplified propped fracture configuration is modelled in a hypothetical small-scale reservoir with idealistic material properties. Production is simulated in time by varying different parameters and the production-induced stress changes are characterised by coupled fluid flow and deformation analysis. It is found from parametric results that the non-uniform reservoir pressure depletion induces a suitable stress state at the fracture tip for further planar propagation. The duration of production to induce the suitable stress state is found to be dependent on a number of parameters. The paper also highlights the implications and limitations of the concept for hydraulic fracturing in the mentioned reservoir conditions, and discussed further research directions.


1993 ◽  
Vol 83 (2) ◽  
pp. 436-449
Author(s):  
C. Allin Cornell ◽  
Shen-Chyun Wu ◽  
Steven R. Winterstein ◽  
James H. Dieterich ◽  
Robert W. Simpson

Abstract This paper presents a phenomenological stochastic model for earthquake recurrence processes involving physical interaction among fault segments. Slip on one segment may reduce (or increase) the time to the next event on another segment or possibly induce an immediate slip on that segment as well. The gross behavior of this model is first observed through simulations; temporal and spatial disorder are observed even when the stochastic aspects are minimized. To estimate the strength of these interactions, we derive factors from the output of three-dimensional elastic dislocation analyses, relating induced stress changes to temporal changes in next-event dates. In a final section, we derive approximate analytical expressions and numerical results for future probabilistic earthquake risk and site hazard, conditional on the elapsed times since events on all relevant fault segments and on the number of events since that may have caused stress changes (interactions).


Author(s):  
F. Dürr ◽  
H. G. Limberger ◽  
R. P. Salathé ◽  
F. Cochet ◽  
A. A. Rybaltovsky ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document