Kinematic effects of number of legs in 6-DOF UPS parallel mechanisms

Robotica ◽  
2017 ◽  
Vol 35 (12) ◽  
pp. 2257-2277 ◽  
Author(s):  
Mohammad H. Abedinnasab ◽  
Farzam Farahmand ◽  
Bahram Tarvirdizadeh ◽  
Hassan Zohoor ◽  
Jaime Gallardo-Alvarado
Keyword(s):  
Parallel Manipulators ◽  
Optimum Number ◽  
Parallel Mechanisms ◽  
Performance Indices ◽  
Singular Configurations ◽  
Redundantly Actuated ◽  
Forward Kinematic Problem ◽  
Kinematic Measures ◽  
Forward Kinematic ◽  
Legged Mechanism

SUMMARYIn this paper, we study the kinematic effects of number of legs in 6-DOF UPS parallel manipulators. A group of 3-, 4-, and 6-legged mechanisms are evaluated in terms of the kinematic performance indices, workspace, singular configurations, and forward kinematic solutions. Results show that the optimum number of legs varies due to priorities in kinematic measures in different applications. The non-symmetric Wide-Open mechanism enjoys the largest workspace, while the well-known Gough–Stewart (3–3) platform retains the highest dexterity. Especially, the redundantly actuated 4-legged mechanism has several important advantages over its non-redundant counterparts and different architectures of Gough–Stewart platform. It has dramatically less singular configurations, a higher manipulability, and at the same time less sensitivity. It is also shown that the forward kinematic problem has 40, 16, and 1 solution(s), respectively for the 6-, 3-, and the 4-legged mechanisms. Superior capabilities of the 4-legged mechanism make it a perfect candidate to be used in more challenging 6-DOF applications in assembly, manufacturing, biomedical, and space technologies.

scholarly journals Type Synthesis of Kinematically Redundant 3T1R Parallel Manipulators

2013 ◽  
Author(s):  
Xianwen Kong ◽  
Damien Chablat ◽  
Stéphane Caro ◽  
Jingjun Yu ◽  
Clément Gosselin
Keyword(s):  
Degrees Of Freedom ◽  
Parallel Manipulators ◽  
Parallel Mechanisms ◽  
Type Synthesis ◽  
Singular Configurations ◽  
Revolute Joints ◽  
Solid Foundation ◽  
Moving Platform ◽  
Forward Kinematic ◽  
Open Issues

A kinematically redundant parallel manipulator (PM) is a PM whose degrees-of-freedom (DOF) are greater than the DOF of the moving platform. It has been revealed in the literature that a kinematically redundant PM has fewer Type II kinematic singular configurations (also called forward kinematic singular configurations, static singular configurations or parallel singular configurations) and/or constraint singular configurations than its non-redundant counterparts. However, kinematically redundant PMs have not been fully explored, and the type synthesis of kinematically redundant PMs is one of the open issues. This paper deals with the type synthesis of kinematically redundant 3T1R PMs (also called SCARA PMs or Schoenflies motion generators), in which the moving platform has four DOF with respect to the base. At first, the virtual-chain approach to the type synthesis of kinematically redundant parallel mechanisms is recalled. Using this approach, kinematically redundant 3T1R PMs are constructed using several compositional units with very few mathematical derivations. The type synthesis of 5-DOF 3T1R PMs composed of only revolute joints is then dealt with systematically. This work provides a solid foundation for further research on kinematically redundant 3T1R PMs.

Gröbner basis and resultant method for the forward displacement of 3-DoF planar parallel manipulators in seven-dimensional kinematic space

Robotica ◽  
2015 ◽  
Vol 34 (11) ◽  
pp. 2610-2628 ◽  
Author(s):  
Davood Naderi ◽  
Mehdi Tale-Masouleh ◽  
Payam Varshovi-Jaghargh
Keyword(s):  
Euclidean Space ◽  
Gröbner Basis ◽  
Three Dimensional ◽  
Parallel Manipulators ◽  
Parallel Robots ◽  
Dimensional Euclidean Space ◽  
Grobner Basis ◽  
Kinematic Space ◽  
Forward Kinematic Problem ◽  
Forward Kinematic

SUMMARYIn this paper, the forward kinematic analysis of 3-degree-of-freedom planar parallel robots with identical limb structures is presented. The proposed algorithm is based on Study's kinematic mapping (E. Study, “von den Bewegungen und Umlegungen,” Math. Ann.39, 441–565 (1891)), resultant method, and the Gröbner basis in seven-dimensional kinematic space. The obtained solution in seven-dimensional kinematic space of the forward kinematic problem is mapped into three-dimensional Euclidean space. An alternative solution of the forward kinematic problem is obtained using resultant method in three-dimensional Euclidean space, and the result is compared with the obtained mapping result from seven-dimensional kinematic space. Both approaches lead to the same maximum number of solutions: 2, 6, 6, 6, 2, 2, 2, 6, 2, and 2 for the forward kinematic problem of planar parallel robots; 3-RPR, 3-RPR, 3-RRR, 3-RRR, 3-RRP, 3-RPP, 3-RPP, 3-PRR, 3-PRR, and 3-PRP, respectively.

A General Methodology for the Forward Kinematic Problem of Symmetrical Parallel Mechanisms and Application to 5-PRUR Parallel Mechanisms (3T2R)

2010 ◽  
Author(s):  
Mehdi Tale Masouleh ◽  
Manfred Husty ◽  
Cle´ment Gosselin
Keyword(s):  
Dimensional Space ◽  
Large Set ◽  
Parallel Mechanisms ◽  
General Methodology ◽  
Higher Dimensional ◽  
Kinematic Mapping ◽  
Rigid Body Displacement ◽  
Forward Kinematic Problem ◽  
Dimensional Projective Space ◽  
Forward Kinematic

In this paper, a general methodology is introduced in order to formulate the FKP of symmetrical parallel mechanisms in a 7-dimensional projective space by the means of the so-called Study’s parameters. The main objective is to consider rigid-body displacement, and consequently the FKP, based on algebraic geometry, rather than rely on classical recipes, such as Euler angles, to assist in problem-solving. The state of the art presented in this paper is general and can be extended to other types of symmetrical mechanisms. In this paper, we limit the concept of kinematic mapping to topologically symmetrical mechanisms, i.e., mechanisms with limbs having identical kinematic arrangement. Exploring the FKP in a higher dimensional space is more challenging since it requires the use of a larger number of coordinates. There are, however, advantages in adopting a large set of coordinates, since this approach leads to expressions with lower degree that do not involve trigonometric functions.

New Resolution Scheme of the Forward Kinematics of Parallel Manipulators Using Extra Sensors

1996 ◽  
Vol 118 (2) ◽  
pp. 214-219 ◽  
Author(s):  
Kilryong Han ◽  
Wankyun Chung ◽  
Y. Youm
Keyword(s):  
Closed Form ◽  
Real Time ◽  
Parallel Manipulators ◽  
Stewart Platform ◽  
Forward Kinematics ◽  
Numerical Examples ◽  
Resolution Scheme ◽  
Real Time Applications ◽  
Forward Kinematic Problem ◽  
Forward Kinematic

This paper presents a new closed-form resolution scheme of the forward kinematics of parallel manipulators based on two concepts, local structurization and mechanism partition. This scheme is applied to 6-DOF Stewart platform manipulators and the effectiveness of this scheme is verified through numerical examples. It is shown that one extra sensor is sufficient for both 3-3 SPM and 6-3 SPM to exactly resolve the forward kinematic problem (FKP) in closed form and two sensors for 6-6 SPM. In previous research, at least three extra sensors were needed for closed-form resolution of the FKP for 6-6 SPM. Consequently, the new resolution scheme is efficient to implement and easy for real-time applications for the control of parallel manipulators.

The Realization of Desired Stiffness of Parallel Mechanism by Adding Redundantly-Actuated Limbs

2017 ◽  
Author(s):  
Shunzhou Huang ◽  
Jue Yu ◽  
Hao Wang ◽  
Yong Zhao ◽  
Xinmin Lai
Keyword(s):  
Parallel Mechanism ◽  
Parallel Manipulators ◽  
Stewart Platform ◽  
Industrial Applications ◽  
Parallel Mechanisms ◽  
Normal Stiffness ◽  
Stiffness Properties ◽  
Mirror Milling ◽  
Redundantly Actuated ◽  
Mapping Models

Stiffness performance is of importance for the use of parallel manipulators in the industrial applications. For this consideration, this paper proposes to realize the desired stiffness properties of parallel mechanism by adding redundantly-actuated limbs. Based on the stiffness mapping models of both the full-DOF and limited-DOF parallel mechanisms, the stiffness variation rules when redundant limbs is introduced into the mechanism are discussed. Moreover, an algorithm for designing the types and configurations of redundant limbs is studied. Two cases are investigated to validate the presented approach. One is about the stiffness decoupling of the Stewart platform, the other is focused on the enhancement of normal stiffness of a Tricept supporting mechanism used in a mirror milling machine designed by us. The result shows that the stiffness performance of Stewart platform can be decoupled when adding six redundantly-actuated limbs that are symmetric with the original active limbs. Besides, the normal stiffness of Tricept mechanism can be enhanced significantly by transforming the passive UP chain to be a redundant actuated chain.

Forward kinematic problem of 5-RPUR parallel mechanisms (3T2R) with identical limb structures

2011 ◽  
Vol 46 (7) ◽  
pp. 945-959 ◽  
Author(s):  
Mehdi Tale Masouleh ◽  
Clément Gosselin ◽  
Manfred Husty ◽  
Dominic R. Walter
Keyword(s):  
Parallel Mechanisms ◽  
Forward Kinematic Problem ◽  
Forward Kinematic

Wrench capabilities of planar parallel manipulators. Part II: Redundancy and wrench workspace analysis

Robotica ◽  
2008 ◽  
Vol 26 (6) ◽  
pp. 803-815 ◽  
Author(s):  
Flavio Firmani ◽  
Alp Zibil ◽  
Scott B. Nokleby ◽  
Ron P. Podhorodeski
Keyword(s):  
Parallel Manipulators ◽  
Mobile Platform ◽  
Operational Cost ◽  
Performance Indices ◽  
Workspace Analysis ◽  
Redundantly Actuated ◽  
Comparison Of The Results ◽  
Actuated Joints ◽  
Planar Parallel Manipulators

SUMMARYThis part of the paper investigates the wrench capabilities of redundantly actuated planar parallel manipulators (PPMs). The wrench capabilities of PPMs are determined by mapping a hypercube from the torque space into a polytope in the wrench space. For redundant PPMs, one actuator output capability constrains the wrench space with a smaller polytope that is contained inside the overall polytope. Performance indices are derived from six study cases. These indices are employed to analyze the wrench workspace for constant orientation of the mobile platform of the non-redundant 3-RRR PPM, and actuation redundant 4-RRR and 3-RRR PPMs, where the underline indicates the actuated joints. A comparison of the results shows that both of the redundantly-actuated PPMs give better wrench capabilities than the non-redundant PPM. However, it is shown that scaled for the operational cost (wrench capabilities divided by total actuation output) the non-redundant 3-RRR PPM provides the highest maximum reachable force, the 3-RRR PPM produces the highest isotropic force, and the 4-RRR yields the highest reachable moment.

A New Approach for Singularity Analysis and Closeness Measurement to Singularities of Parallel Manipulators

2012 ◽  
Vol 4 (4) ◽  
Author(s):  
Xin-Jun Liu ◽  
Chao Wu ◽  
Jinsong Wang
Keyword(s):  
Parallel Manipulator ◽  
Parallel Manipulators ◽  
Singularity Analysis ◽  
Challenging Problem ◽  
Performance Indices ◽  
New Approach ◽  
Singular Configurations ◽  
Different Types ◽  
Force Transmissibility ◽  
Singular Configuration

Singularity analysis is one of the most important issues in the field of parallel manipulators. An approach for singularity analysis should be able to not only identify all possible singularities but also explain their physical meanings. Since a parallel manipulator is always out of control at a singularity and its neighborhood, it should work far from singular configurations. However, how to measure the closeness between a pose and a singular configuration is still a challenging problem. This paper presents a new approach for singularity analysis of parallel manipulators by taking into account motion/force transmissibility. Several performance indices are introduced to measure the closeness to singularities. By using these indices, a uniform “metric” can be found to represent the closeness to singularities for different types of nonredundant parallel manipulators.

Sign in / Sign up

Export Citation Format

Share Document