A Recursive Algorithm for the Forward Kinematic Analysis of Robotic Systems Using Euler Angles

Forward kinematics is one of the main research fields in robotics, where the goal is to obtain the position of a robot’s end-effector from its joint parameters. This work presents a method for achieving this using a recursive algorithm that builds a 3D computational model from the configuration of a robotic system. The orientation of the robot’s links is determined from the joint angles using Euler Angles and rotation matrices. Kinematic links are modeled sequentially, the properties of each link are defined by its geometry, the geometry of its predecessor in the kinematic chain, and the configuration of the joint between them. This makes this method ideal for tackling serial kinematic chains. The proposed method is advantageous due to its theoretical increase in computational efficiency, ease of implementation, and simple interpretation of the geometric operations. This method is tested and validated by modeling a human-inspired robotic mobile manipulator (CHARMIE) in Python.

Optimization of DH Parameters of 6R Robotic Manipulator Using JAYA Approach

Manipulation of robots is carried out by the operators through a sequence of commands. However, the accuracy of the manipulation is still hindered due to parameter uncertainty. This results in less accurate robotic operations and hence affects the job performance. Due to measurement errors and sensor faults, the operation of robots malfunctions. Generally, errors are reduced with the use of high precision sensors and correcting hardware faults. However, corrections can also be made on a software platform to handle the correction process. Presently, the Denavit–Hartenberg (DH) parameters of a robotic manipulator are optimized for forward kinematics problems. The optimization is carried out using the JAYA approach. The 6R MTAB Aristo XT robot is selected as a case study for the experimental validation of the proposed approach. Experimental results reveal that the optimization of DH parameters improves accuracy for forward kinematic estimation problems. The proposed JAYA approach can further be extended to other robotic manipulators for parameter optimization problems.

Forward Kinematic and Jacobian Matrix for the Prosthetic Human Finger Actuated by Links

The most important function of a prosthetic hand is their ability to perform tasks in a manner similar to a natural hand, so it is necessary to perform kinematic analysis to determine the performance and the ability of the prosthetic human finger design to work normally and smoothly when it's drive by two sets of links that embedded in its structure and pulled by a servomotor, so the Denvit-Hartenberg method was used to analyse the forward kinematics for the prosthetic finger joints to deduction the trajectory of the fingertip and the velocity of the joints was computed by using the Jacobian matrix. The prosthetic finger was modelled by the Solidwork - 2018 program and the results of kinematics were verified using MATLAB. The analyses that were conducted on the design showed that the designed prosthetic finger has the ability to perform movements and meets the functional requirements for which it is designed.

Kinematic analysis of an augmented 3-RPSP tripod mechanism with six degrees of freedom for bone reduction surgery

Robotic-assisted bone reduction surgery consists in using robots to reconnect patients’ bone fragments prior to fracture healing. The goal of this study is to propose a novel augmented 3-RPSP tripod mechanism with six degree of freedom for longitudinal bone reduction surgery. Its inverse kinematic model is studied and its forward kinematic model is solved by establishing the constraint equations, applying Sylvester’s dialytic method and finding the solutions of the resulting polynomial equation. The velocity model is calculated and its Jacobian matrix is used to identify its singular configurations. In comparison to the Stewart–Gough platform that is a typical mechanism used in this application, the proposed mechanism offers larger reachable workspace which is an important aspect in the femoral shaft bone reduction. A Physiguide and Msc Adams software are used to carry out a simulation of a real femur fracture reduction using the proposed mechanism to validate its suitability. A robotic prototype has been designed and manufactured in order to test its capability of performing diaphyseal femur reduction surgery.

Constraint Equations for a Planar Parallel Platform

<p>The aim of this thesis is to apply the Grünwald–Blaschke kinematic mapping to standard types of parallel general planar three-legged platforms in order to obtain the univariate polynomials which provide the solution of the forward kinematic problem. We rely on the method of Gröbner basis to reach these univariate polynomials. The Gröbner basis is determined from the constraint equations of the three legs of the platforms. The degrees of these polynomials are examined geometrically based on Bezout’s Theorem. The principle conclusion is that the univariate polynomials for the symmetric platforms under circular constraints are of degree six, which describe the maximum number of real solutions. The univariate polynomials for the symmetric platforms under linear constraints are of degree two, that describe the maximum number of real solutions.</p>

Constraint Equations for a Planar Parallel Platform

<p>The aim of this thesis is to apply the Grünwald–Blaschke kinematic mapping to standard types of parallel general planar three-legged platforms in order to obtain the univariate polynomials which provide the solution of the forward kinematic problem. We rely on the method of Gröbner basis to reach these univariate polynomials. The Gröbner basis is determined from the constraint equations of the three legs of the platforms. The degrees of these polynomials are examined geometrically based on Bezout’s Theorem. The principle conclusion is that the univariate polynomials for the symmetric platforms under circular constraints are of degree six, which describe the maximum number of real solutions. The univariate polynomials for the symmetric platforms under linear constraints are of degree two, that describe the maximum number of real solutions.</p>

Six DOF Robotic Arm Prototype Modelling By Matlab

The study in this paper allows us to control the manipulator and achieve any desired position and orientation. The Forward Kinematics was done using Denavait Hartenberg (DH) parameters, also the forward kinematics equations and homogenous transformation matrix was validated using MATLAB Toolbox. The modeling was carried out using the Peter Corke robotics toolbox. Finally, the forward kinematic study and the robot arm’s movement equations were compared with practical measurements to make sure it fulfilled the desired purpose and that it could point to the desired coordinates with a precision of ±0.5 cm.

Development of a revolute-type kinematic model for human upper limb using a matrix approach

A mathematical model is proposed for a revolute joint mechanism with an n-degree of freedom (DOF). The matrix approach is used for finding the relation between two consecutive links to determine desired link parameters such as position, velocity and acceleration using the forward kinematic approach. The matrix approach was confirmed for a proposed 10 DOF revolute type (R-type) human upper limb model with servo motors at each joint. Two DOFs are considered each at shoulder, elbow and wrist joint, followed by four DOF for the fingers. Two DOFs were considered for metacarpophalangeal (mcp) and one DOF each for proximal interphalangeal (pip) and distal interphalangeal (dip) joints. MATLAB script function was used to evaluate the mathematical model for determining kinematic parameters for all the proposed human upper limb model joints. The simplified method for kinematic analysis proposed in this paper will further simplify the dynamic modeling of any mechanism for determining joint torques and hence, easy to design control system for joint movements.

Kinematic modeling and solution of rigid-flexible and variable-diameter underwater continuous manipulator with load

This paper presents a method to solve the kinematics of a rigid-flexible and variable-diameter continuous manipulator. The multi-segment underwater manipulator is driven by McKibben water hydraulic artificial muscle (WHAM). Considering the effect of elasticity and friction, we optimized the static mathematical model of WHAM. The kinematic model of the manipulator with load is established based on the hypothesis of piecewise constant curvature (PCC). We developed an optimization algorithm to calculate the length of the WHAMs according to the principle of minimum strain energy and obtain the configuration space parameters of the kinematic model. Based on the infinitesimal method, the homogeneous transformation matrices of the variable-diameter bending sections are computed, and the terminal position and attitude are obtained. In this paper, we studied the working space of the manipulator by quantitative analysis of the impact factors including pressure and load. A deep neural network (DNN) with six hidden layers is designed to solve inverse kinematics. The forward kinematic results are used to train and test the DNN, and the correlation coefficient between the output and target samples reaches 0.945. We carried out an underwater experiment and verified the effectiveness of the kinematic modeling and solution method.

KINEMATICS ANALYSIS AND IMPLEMENTATION OF THREE DEGREES OF FREEDOM ROBOTIC ARM BY USING MATLAB

The kinematics modeling of the robot arm plays an important role in robot control. This paper presents the kinematic model of a three-degree of freedom articulated robot arm, which is designed for picking and placing an application with hand gripper, where a robot has been manufactured for that purpose. The forward kinematic model has been presented in order to determine the end effector’s poses using the Denavit-Hartenberg (DH) convention. For inverse kinematics, an algebraic solution based on trigonometric formulas mixed with geometric method was adopted for a 3 DOF modular manipulator taking into account the existence of a shoulder offset. MATLAB software was used as a tool to simulate and implement the motional characteristics of the robot arm, by creating a 3D visual software package under designing a Graphical User Interface "GUI" with a support simulation from robotic Toolbox (Rtb 10.3). Finally, an electronic interfacing circuit between the GUI program and the robot arm was developed using Arduino microcontroller to control the robot motion. The presented work can be applicable for learning the reality interface design methodology of the other kinds of robot manipulators and achieve a suitable solution for the motional characteristics