Terrestrial material input to the northwest shelf of Australia through the Pliocene‐Pleistocene period and its implications on continental climates

Author(s):  
Yuxin He ◽  
Huanye Wang
2011 ◽  
Vol 347-353 ◽  
pp. 2961-2966
Author(s):  
Dian Ming Geng ◽  
Jia Xiang Liu

In order to study the development of regional recycling economy, the material inputs and outputs of the eco-economic system in Shandong Province during the period from 1996 to 2009 were systematically analyzed by the material flow analysis(MFA). The results show that, (1)excluding water, material inputs and outputs rose persistently, but both were lower than the rate of GDP growth. (2)Water supply had a turning point in 2003, from 25.239 billion tons down to 21.934 billion tons, followed by the total annual water supply has been maintained at 220 million tons. At the same time the amount of wastewater emissions is increasing, especially domestic wastewater emissions had faster growth and that increased pressure on the regional water environment;(3) Steady increase in material input intensity, material output intensity presented a first increased and then decreased trend, that showed since Shandong Province proposed the strategic planning to develop circular economy, the development of regional circular economy have improved the material utilization efficiency and made a material reduction in output in the case of material input growth achieved. The rapid increase of material input and output efficiency further illustrated the efficiency of resource comprehensive utilization and waste output have been significantly improved.


1975 ◽  
Vol 8 (1) ◽  
pp. 1-23 ◽  
Author(s):  
N. Stephens ◽  
J. R. Creighton ◽  
M. A. Hannon

2013 ◽  
Vol 747 ◽  
pp. 571-574 ◽  
Author(s):  
Zulkifli Mohamad Ariff ◽  
T.H. Khang

The possibility of using Cadmould software to simulate the filling behaviour of a natural rubber compound during an injection moulding process was investigated. For the simulation process, the determination of required material input data involving the rheological and cure kinetics data of the designed rubber compound were conducted. It was discovered that the acquired data were able to function as reliable material input data as they were comparable with related data available in the Cadmould software materials database. Verification of the simulated filling profiles by experimental short shots specimens showed that the Cadmould Rubber Package was able to predict the realistic filling behaviour of the formulated natural rubber compound inside the mould cavity when the measured material data were utilized. Whereas, the usage of available material database from the software failed to model the mould filling progression of the intended natural rubber compound.


2008 ◽  
Vol 87 (4) ◽  
pp. 359-361 ◽  
Author(s):  
T. van der Hammen ◽  
B. van Geel

AbstractDuring the warm Bølling-Allerød interstadial, tree species migrated from their refugia in southern Europe northwards into the area within the present temperate climatic zone. It is evident from high levels of charcoal in fossil records in this region that, especially during the later part of the Bølling-Allerød interstadial, many fires occurred. The start of the Younger Dryas was characterised by rapid and intense cooling and rising water tables, with catastrophic effects on the vegetation. Thermophilous pine trees could not survive the cold Younger Dryas climate. Dead wood provided an abundant source of fuel for intense, large-scale fires seen in many records as a concentration of charcoal particles in so-called ’Usselo-soils’ dated to ca 10,95014C BP. A similar trend in increased charcoal indicating increased burning is seen at many sites across North America at this time and it has been suggested by Firestone et al. (2007) that this was caused by an explosion of extra-terrestrial material over northern North America, causing the Younger Dryas climate cooling and Megafaunal extinction. We argue that there is no need to invoke an extraterrestrial cause to explain the charcoal in the fossilized soils. The volume of forest trees that died as a result of the cold Younger Dryas climate would easily have supplied sufficient fuel for intense, large-scale fires and can be used to account for the concentration of charcoal particles. As soils were no longer covered by dense vegetation, much erosion occurred during the Younger Dryas and therefore, at many places, Usselo soils, rich in charcoal, were preserved under aeolian sand dunes.


2000 ◽  
Vol 10 (1) ◽  
pp. 7-34 ◽  
Author(s):  
Colin Renfrew

The issue of ‘knowability’ in relation to the origins and distribution of the language families of the world is addressed, and recent advances in historical linguistics and molecular genetics reviewed. While the much-debated problem of the validity of the concept of the language ‘macrofamily’ cannot yet be resolved, it is argued that a time depth for the origins of language families greater than the conventional received figure of c. 6000 years may in some cases be appropriate, allowing the possibility of a correlation between language dispersals and demographic processes following the end of the Pleistocene period. The effects of these processes may still be visible in the linguistic ‘spread zones’, here seen as often the result of farming dispersals, contrasting with the linguistic ‘mosaic zones’ whose early origins may sometimes go back to initial colonization episodes during the late Pleistocene period. If further work in historical linguistics as well as in archaeology and molecular genetics upholds these correlations a ‘new synthesis’, whose outlines may already be discerned, is likely to emerge. This would have important consequences for prehistoric archaeology, and would be of interest also to historical linguists and molecular geneticists. If, however, the proposed recognition of such patterning proves illusory the prospects for ‘knowability’ appear to be less favourable.


Author(s):  
Kateryna Kamchatna-Stepanova

The construction of an information model of the processes of gear processing of hardened large-modular chevron gears is one of the stages of control of the technological structure and parameters of the automation of the design of the technological process. Taking into account the principles of information classification, the automated gear processing process is considered as a control object, consisting of a number of technological objects: initial material (input of the control object); environment (process conditions); gear wheel (output of the control object, quantitative and qualitative characteristics of the surface layer) The construction of an information model of the processes of gear processing of hardened large-modular chevron gears is one of the stages of control of the technological structure and parameters of the automation of the design of the technological process.


Sign in / Sign up

Export Citation Format

Share Document