scholarly journals Prediction of flow noise around a cylinder based on Large-Eddy Simulation and acoustic analogy method

2019 ◽  
Vol 283 ◽  
pp. 08003
Author(s):  
Qikai Qin ◽  
Dejiang Shang ◽  
Yongwei Liu ◽  
Tianyu Wang
Keyword(s):  
Flow Field ◽  
Large Eddy Simulation ◽  
Transient Flow ◽  
Turbulent Model ◽  
Acoustic Analogy ◽  
Flow Around A Cylinder ◽  
Flow Noise ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Field Noise

In this article, a hybrid method combining large eddy simulation with acoustic analogy is presented to predict three-dimensional far field noise induced by flow around a cylinder. Firstly, the governing equation including RANS equations with shear-stress transport (SST) k-ω turbulent model is numerically solved for steady flow field by using Ansys Fluent. Transient flow field is numerically solved by LES. Then, the flow field simulation results are used to compute the flow-induced noise with the FW-H integral equation method and BEM method based on Lighthill acoustic analogy equation in Actran. Before using for flow around a cylinder, accuracy of flow turbulent model in predicting turbulent flow around a cylinder is tested by comparing with available experimental data. According on the simulation result, the characteristic of the acoustic field, noise at some special points in frequency domain, the noise radiation directivity are studied. Analysis of noise distribution and frequency spectrum curves shows that dipole source takes the dominant place in the noise around a cylinder under the conditions of this article. The flow noise around a cylinder is mainly concentrated in the low frequency range.

scholarly journals Large eddy simulation of airfoil self-noise using OpenFOAM

2018 ◽  
Vol 90 (1) ◽  
pp. 126-133 ◽  
Author(s):  
Hasan Kamliya Jawahar ◽  
Yujing Lin ◽  
Mark Savill
Keyword(s):  
Experimental Data ◽  
Wind Tunnel ◽  
Large Eddy Simulation ◽  
Acoustic Analogy ◽  
Content Type ◽  
Installation Effects ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Field Noise ◽  
Airfoil Self Noise

Purpose The purpose of this paper is to investigate airfoil self-noise generation and propagation by using a hybrid method based on the large-eddy simulation (LES) approach and Curle’s acoustic analogy as implemented in OpenFOAM. Design/methodology/approach Large-eddy simulation of near-field flow over a NACA6512-63 airfoil at zero angle of attack with a boundary layer trip at Rec = 1.9 × 105 has been carried out using the OpenFOAM® computational fluid dynamics (CFD) code. Calculated flow results are compared with published experimental data. The LES includes the wind tunnel installation effects by using appropriate inflow boundary conditions obtained from a RANS κ – ω SST model computation of the whole wind tunnel domain. Far-field noise prediction was achieved by an integral method based on Curle’s acoustic analogy. The predicted sound pressure levels are validated against the experimental data at various frequency ranges. Findings The numerical results presented in this paper show that the flow features around a NACA6512-63 airfoil have been correctly captured in OpenFOAM LES calculations. The mean surface pressure distributions and the local pressure peaks for the step trip setup agree very well with the experimental measurements. Aeroacoustic prediction using Curle’s analogy shows an overall agreement with the experimental data. The sound pressure level-frequency spectral analysis produces very similar data at low to medium frequency, whereas the experimentally observed levels are slightly over predicted at a higher frequency range. Practical implications This study has achieved and evaluated an alternative aeroacoustic simulation method based on the combination of LES with a simple Smagorinsky SGS model and Curle’s analogy, as implemented in the OpenFOAM CFD code. The unsteady velocity/pressure source data produced can be used for any simpler analytically based far-field noise prediction scheme. Originality/value A complete integration of the LES and Curle’s acoustic analogy for aeroacoustic simulations has been achieved in OpenFOAM. The capability and accuracy of the hybrid method are fully evaluated for high-camber airfoil self-noise predictions. Wind tunnel installation effects have been incorporated properly into the LES.

Wake-Airfoil Interaction as Broadband Noise Source: A Large-Eddy Simulation Study

2005 ◽  
Vol 4 (1-2) ◽  
pp. 93-115 ◽  
Author(s):  
Jérôme Boudet ◽  
Nathalie Grosjean ◽  
Marc C. Jacob
Keyword(s):  
Large Eddy Simulation ◽  
Particle Image ◽  
Broadband Noise ◽  
Far Field ◽  
Acoustic Analogy ◽  
Eddy Simulation ◽  
Naca0012 Airfoil ◽  
Image Velocimetry ◽  
Large Eddy ◽  
Proper Orthogonal

A large-eddy simulation is carried out on a rod-airfoil configuration and compared to an accompanying experiment as well as to a RANS computation. A NACA0012 airfoil (chord c = 0.1 m) is located one chord downstream of a circular rod (diameter d = c/10, Red = 48 000). The computed interaction of the resulting sub-critical vortex street with the airfoil is assessed using averaged quantities, aerodynamic spectra and proper orthogonal decomposition (POD) of the instantaneous flow fields. Snapshots of the flow field are compared to particle image velocimetry (PIV) data. The acoustic far field is predicted using the Ffowcs Williams & Hawkings acoustic analogy, and compared to the experimental far field spectra. The large-eddy simulation is shown to accurately represent the deterministic pattern of the vortex shedding that is described by POD modes 1 & 2 and the resulting tonal noise also compares favourably to measurements. Furthermore higher order POD modes that are found in the PIV data are well predicted by the computation. The broadband content of the aerodynamic and the acoustic fields is consequently well predicted over a large range of frequencies ([0 kHz; 10 kHz]).

Large Eddy Simulation of Flow and Heat Transfer Mechanism in Matrix Cooling Channel

2017 ◽  
Author(s):  
Yigang Luan ◽  
Lianfeng Yang ◽  
Bo Wan ◽  
Tao Sun
Keyword(s):  
Heat Transfer ◽  
Flow Field ◽  
Large Eddy Simulation ◽  
Gas Turbine ◽  
Transfer Mechanism ◽  
Heat Transfer Mechanism ◽  
Longitudinal Vortices ◽  
Eddy Simulation ◽  
Flow And Heat Transfer ◽  
Large Eddy

Gas turbine engines have been widely used in modern industry especially in the aviation, marine and energy fields. The efficiency of gas turbines directly affects the economy and emissions. It’s acknowledged that the higher turbine inlet temperatures contribute to the overall gas turbine engine efficiency. Since the components are subject to the heat load, the internal cooling technology of turbine blades is of vital importance to ensure the safe and normal operation. This paper is focused on exploring the flow and heat transfer mechanism in matrix cooling channels. In order to analyze the internal flow field characteristics of this cooling configuration at a Reynolds number of 30000 accurately, large eddy simulation method is carried out. Methods of vortex identification and field synergy are employed to study its flow field. Cross-sectional views of velocity in three subchannels at different positions have been presented. The results show that the airflow is strongly disturbed by the bending part. It’s concluded that due to the bending structure, the airflow becomes complex and disordered. When the airflow goes from the inlet to the turning, some small-sized and discontinuous vortices are formed. Behind the bending structure, the size of the vortices becomes big and the vortices fill the subchannels. Because of the structure of latticework, the airflow is affected by each other. Airflow in one subchannel can exert a shear force on another airflow in the opposite subchannel. It’s the force whose direction is the same as the vortex that enhances the longitudinal vortices. And the longitudinal vortices contribute to the energy exchange of the internal airflow and the heat transfer between airflow and walls. Besides, a comparison of the CFD results and the experimental data is made to prove that the numerical simulation methods are reasonable and acceptable.

scholarly journals Investigation of the velocity field downstream of a benchmark vent using numerical simulation and hot-wire anemometry

2019 ◽  
Vol 213 ◽  
pp. 02076
Author(s):  
Jan Sip ◽  
Frantisek Lizal ◽  
Jakub Elcner ◽  
Jan Pokorny ◽  
Miroslav Jicha
Keyword(s):  
Fluid Dynamics ◽  
Numerical Simulation ◽  
Velocity Field ◽  
Flow Field ◽  
Large Eddy Simulation ◽  
Turbulence Models ◽  
Hot Wire ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Precise Prediction

The velocity field in the area behind the automotive vent was measured by hot-wire anenemometry in detail and intensity of turbulence was calculated. Numerical simulation of the same flow field was performed using Computational fluid dynamics in commecial software STAR-CCM+. Several turbulence models were tested and compared with Large Eddy Simulation. The influence of turbulence model on the results of air flow from the vent was investigated. The comparison of simulations and experimental results showed that most precise prediction of flow field was provided by Spalart-Allmaras model. Large eddy simulation did not provide results in quality that would compensate for the increased computing cost.

Sign in / Sign up

Export Citation Format

Share Document