Independent particle size and shape estimation from polarization fluctuation spectroscopy

2004 ◽  
Vol 15 (5) ◽  
pp. 771-776 ◽  
Author(s):  
J G Walker ◽  
P C Y Chang ◽  
K I Hopcraft ◽  
E Mozaffari
2022 ◽  
Author(s):  
Charles Nelson Helms ◽  
Stephen Joseph Munchak ◽  
Ali Tokay ◽  
Claire Pettersen

Abstract. Measurements of snowflake particle size and shape are important for studying the snow microphysics. While a number of instruments exist that are designed to measure these important parameters, this study focuses on the measurement techniques of three digital video disdrometers: the Precipitation Imaging Package (PIP), the Multi-Angle Snowflake Camera (MASC) and the Two-Dimensional Video Disdrometer (2DVD). To gain a better understanding of the relative strengths and weaknesses of these instruments and to provide a foundation upon which comparisons can be made between studies using data from different instruments, we perform a comparative analysis of the measurement algorithms employed by each of the three instruments by applying the algorithms to snowflake images captured by PIP during the ICEP-POP 2018 field campaign. Our analysis primarily focuses on the measurements of area, equivalent diameter, and aspect ratio. Our findings indicate that area and equi-area diameter measurements using the 2DVD camera setup should be the most accurate, followed by MASC, which is slightly more accurate than PIP. In terms of the precision of the area and equi-area diameter measurements, however, MASC is considerably more precise than PIP or 2DVD, which provide similar precision once the effects of the PIP image compression algorithm are taken into account. Both PIP and MASC use shape-fitting algorithms to measure aspect ratio. While our analysis of the MASC aspect ratio suggests the measurements are reliable, our findings indicate that both the ellipse and rectangle aspect ratios produced by PIP under-performed considerably due to the shortcomings of the PIP shape-fitting techniques. That said, we also demonstrate that reliable measurements of aspect ratio can be retrieved from PIP by reprocessing the PIP images using either the MASC shape-fitting technique or a tensor-based ellipse-fitting technique. Because of differences in instrument design, 2DVD produces measurements of particle horizontal and vertical extent rather than length and width. Furthermore, the 2DVD measurements of particle horizontal extent can be contaminated by horizontal particle motion. Our findings indicate that, although the correction technique used to remove the horizontal motion contamination performs remarkably well with snowflakes despite being designed for use with rain drops, the 2DVD measurements of particle horizontal extent are potentially unreliable.


2014 ◽  
Vol 71 (2) ◽  
Author(s):  
Hussain, S. ◽  
M.K Abdul Hamid ◽  
A.R Mat Lazim ◽  
A.R. Abu Bakar

Brake wear particles resulting from friction between the brake pad and disc are common in brake system. In this work brake wear particles were analyzed based on the size and shape to investigate the effects of speed and load applied to the generation of brake wear particles. Scanning electron microscopy (SEM) with energy-dispersive X-ray spectroscopy (EDX) was used to identify the size, shape and element compositions of these particles. Two types of brake pads were studied which are non-asbestos organic and semi metallic brake pads. Results showed that the size and shape of the particles generatedvary significantly depending on the applied brake load, and less significantly on brake disc speed. The wear particle becomes bigger with increasing applied brake pressure. The wear particle size varies from 300 nm to 600 µm, and contained elements such as carbon, oxygen, magnesium, aluminum, sulfur and iron.


2017 ◽  
Vol 2017 ◽  
pp. 1-9 ◽  
Author(s):  
Zhaolin Lu ◽  
Xiaojuan Hu ◽  
Yao Lu

Particle morphology, including size and shape, is an important factor that significantly influences the physical and chemical properties of biomass material. Based on image processing technology, a method was developed to process sample images, measure particle dimensions, and analyse the particle size and shape distributions of knife-milled wheat straw, which had been preclassified into five nominal size groups using mechanical sieving approach. Considering the great variation of particle size from micrometer to millimeter, the powders greater than 250 μm were photographed by a flatbed scanner without zoom function, and the others were photographed using a scanning electron microscopy (SEM) with high-image resolution. Actual imaging tests confirmed the excellent effect of backscattered electron (BSE) imaging mode of SEM. Particle aggregation is an important factor that affects the recognition accuracy of the image processing method. In sample preparation, the singulated arrangement and ultrasonic dispersion methods were used to separate powders into particles that were larger and smaller than the nominal size of 250 μm. In addition, an image segmentation algorithm based on particle geometrical information was proposed to recognise the finer clustered powders. Experimental results demonstrated that the improved image processing method was suitable to analyse the particle size and shape distributions of ground biomass materials and solve the size inconsistencies in sieving analysis.


Author(s):  
A. Hizal ◽  
B. Sadasivam ◽  
D. Arola

A preliminary study was conducted to evaluate the parametric dependence of the residual stress distributions in bone that result from an abrasive air-jet surface treatment. Specifically, the influence of particle size and shape used in the treatment on the residual stress, propensity of embedding particles and material removal were studied. Rectangular beams of cortical bone were prepared from bovine femurs and treated with aluminum oxide and glass particles with different treatment angles. Residual stresses within the bone were quantified in terms of the radius of curvature of the bone specimens measured before and after the treatments, as well as a function of time to quantify decay in the stress. The sub-surface distribution was also examined using the layer removal technique. Results showed that the particle size and shape could be used to control the amount of material removal and the magnitude of residual stress within the treated surfaces. An increase in size of the glass particles resulted in an increase in the residual stress and a decrease in material removed during the treatment. The magnitude of residual stress ranged from 22 MPa to nearly 44 MPa through modulation of the particle qualities (size and shape). A microscopic examination of the treated surfaces suggests that the residual stresses resulted primarily from near-surface deformation.


Sign in / Sign up

Export Citation Format

Share Document