scholarly journals The High Luminosity LHC interaction region magnets towards series production

2021 ◽  
Author(s):  
Ezio Todesco ◽  
Hugo Bajas ◽  
Marta Bajko ◽  
Amalia Ballarino ◽  
Susana Izquierdo Bermudez ◽  
...  
Keyword(s):  
Interaction Region ◽  
Series Production ◽  
High Luminosity

scholarly journals High luminosity interaction region design for collisions inside high field detector solenoid

2012 ◽  
Vol 7 (03) ◽  
pp. T03002-T03002 ◽  
Author(s):  
C Milardi ◽  
M A Preger ◽  
P Raimondi ◽  
F Sgamma
Keyword(s):  
High Field ◽  
Interaction Region ◽  
High Luminosity

Superconducting quadrupole magnet R&D in the interaction region of CEPC

2021 ◽  
pp. 2142007
Author(s):  
Chuang Shen ◽  
Yingshun Zhu ◽  
Xiangchen Yang ◽  
Ran Liang ◽  
Fusan Chen
Keyword(s):  
Magnetic Field ◽  
Interaction Region ◽  
High Luminosity ◽  
Design Study ◽  
Interaction Point ◽  
High Gradient ◽  
Quadrupole Magnet ◽  
Electron Positron ◽  
Magnetic Length ◽  
Design And Manufacture

To obtain high luminosity, compact high gradient quadrupole magnets QD0 and QF1 are required on both sides of the interaction points of the proposed Circular Electron Positron Collider (CEPC). QD0 is a double aperture superconducting quadrupole closest to the interaction point with a crossing angle between two aperture centerlines of 33 mrad. Magnetic field crosstalk between two apertures of QD0 is negligible using iron yoke, and the 3D coil end is optimized by ROXIE. In the design study, both NbTi conductor and HTS conductor are taken into account. The first step of the R&D is to design and manufacture a QD0 short model magnet with a magnetic length of 0.5 m. In this paper, the R&D status of QD0 short model magnet is described, and the design study of quadrupole magnet including NbTi technology and HTS Bi-2212 technology is presented.

The high luminosity interaction region for a ring–ring Large Hadron Electron Collider

2013 ◽  
Vol 40 (12) ◽  
pp. 125004 ◽  
Author(s):  
R B Appleby ◽  
L Thompson ◽  
B Holzer ◽  
M Fitterer ◽  
N Bernard ◽  
...  
Keyword(s):  
Interaction Region ◽  
High Luminosity

Accelerator physics design in the interaction region for CEPC double ring scheme

2019 ◽  
Vol 34 (13n14) ◽  
pp. 1940002 ◽  
Author(s):  
Sha Bai ◽  
Chenghui Yu ◽  
Yiwei Wang ◽  
Yingshun Zhu ◽  
Jie Gao
Keyword(s):  
Radiation Power ◽  
Critical Energy ◽  
Small Region ◽  
Research Area ◽  
Interaction Region ◽  
Design Parameters ◽  
Accelerator Physics ◽  
High Luminosity ◽  
Double Ring ◽  
Electron Positron

With the discovery of the Higgs boson at around 125 GeV, a circular Higgs factory design with high luminosity [Formula: see text] is becoming more popular in the accelerator world. The CEPC project in China is one of them. Machine Detector Interface (MDI) is the key research area in electron–positron colliders, especially in CEPC; it is one of the criteria to measure the accelerator and detector design performance. Because of the limited space available in the designed tunnel, many equipment including magnets, beam diagnostic instruments, masks, vacuum pumps, and components of the detector must coexist in a very small region. In this paper, some important MDI issues will be reported for the Interaction Region (IR) design, e.g. the final doublet quadrupoles physics design parameters, beam-stay-clear region and beam pipe, synchrotron radiation power and critical energy are also calculated.

Analysis of Geometry and Field Quality Along the Series Production of the 11 T Dipole for the High Luminosity LHC

2021 ◽  
Vol 31 (5) ◽  
pp. 1-6
Author(s):  
Dariusz Pulikowski ◽  
Arnaud Devred ◽  
Lucio Fiscarelli ◽  
Susana Izquierdo Bermudez ◽  
Jose Luis Rudeiros Fernandez ◽  
...  
Keyword(s):  
Series Production ◽  
High Luminosity ◽  
Field Quality

Introduction: the tv series production system in Germany

IKON ◽  
2014 ◽  
pp. 27-28
Author(s):  
Paolo Braga ◽  
Erica Negri ◽  
Michele Zatta
Keyword(s):  
Production System ◽  
Series Production

AM-Serienproduktion für die Automobilindustrie/AM series production for the automotive industry

2020 ◽  
Vol 110 (11-12) ◽  
pp. 752-757
Author(s):  
Lukas Weiser ◽  
Marco Batschkowski ◽  
Niclas Eschner ◽  
Benjamin Häfner ◽  
Ingo Neubauer ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Automotive Industry ◽  
Series Production ◽  
Production Scale ◽  
Additive Fertigung ◽  
Small Series ◽  
Start Up ◽  
3D Printed ◽  
Component Quality

Die additive Fertigung schafft neue Gestaltungsfreiheiten. Im Rahmen des Prototypenbaus und der Kleinserienproduktion kann das Verfahren des selektiven Laserschmelzens genutzt werden. Die Verwendung in der Serienproduktion ist bisher aufgrund unzureichender Bauteilqualität, langen Anlaufzeiten sowie mangelnder Automatisierung nicht im wirtschaftlichen Rahmen möglich. Das Projekt „ReAddi“ möchte eine erste prototypische Serienfertigung entwickeln, mit der additiv gefertigte Bauteile für die Automobilindustrie wirtschaftlich produziert werden können. Additive manufacturing (AM) offers new freedom of design. The selective laser-powderbed fusion (L-PBF) process can be used for prototyping and small series production. So far, it has not been economical to use it on a production scale due to insufficient component quality, long start-up times and a lack of automation. The project ReAddi aims to develop a first prototype series production to cost-effectively manufacture 3D-printed components for the automotive industry.

Sign in / Sign up

Export Citation Format

Share Document