scholarly journals Pulsed Laser-Induced Effects in the Material Properties of Tungsten Thin Films

2007 ◽  
Vol 59 ◽  
pp. 436-439
Author(s):  
R Evans ◽  
S Camacho-López ◽  
M A Camacho-López ◽  
C Sánchez-Pérez ◽  
A Esparza-García
Keyword(s):  
Thin Films ◽  
Material Properties ◽  
Pulsed Laser

Polypyrrole thin films for gas sensors prepared by Matrix-Assisted Pulsed Laser Evaporation technology: Effect of deposition parameters on material properties

2009 ◽  
Vol 517 (6) ◽  
pp. 2083-2087 ◽  
Author(s):  
Dušan Kopecký ◽  
Martin Vrňata ◽  
Filip Vysloužil ◽  
Vladimír Myslík ◽  
Přemysl Fitl ◽  
...  
Keyword(s):  
Thin Films ◽  
Gas Sensors ◽  
Material Properties ◽  
Pulsed Laser ◽  
Laser Evaporation ◽  
Deposition Parameters

Observations on the growth of YBa2Cu3O7-δ thin films on MgO by pulsed-laser ablation

1991 ◽  
Vol 49 ◽  
pp. 1068-1069
Author(s):  
M. Grant Norton ◽  
C. Barry Carter
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Laser Ablation ◽  
Substrate Surface ◽  
Pulsed Laser ◽  
Pulsed Laser Ablation ◽  
Thin Film Deposition ◽  
Film Deposition ◽  
Laser Ablation Process ◽  
Deposition Parameters

Pulsed-laser ablation has been widely used to produce high-quality thin films of YBa2Cu3O7-δ on a range of substrate materials. The nonequilibrium nature of the process allows congruent deposition of oxides with complex stoichiometrics. In the high power density regime produced by the UV excimer lasers the ablated species includes a mixture of neutral atoms, molecules and ions. All these species play an important role in thin-film deposition. However, changes in the deposition parameters have been shown to affect the microstructure of thin YBa2Cu3O7-δ films. The formation of metastable configurations is possible because at the low substrate temperatures used, only shortrange rearrangement on the substrate surface can occur. The parameters associated directly with the laser ablation process, those determining the nature of the process, e g. thermal or nonthermal volatilization, have been classified as ‘primary parameters'. Other parameters may also affect the microstructure of the thin film. In this paper, the effects of these ‘secondary parameters' on the microstructure of YBa2Cu3O7-δ films will be discussed. Examples of 'secondary parameters' include the substrate temperature and the oxygen partial pressure during deposition.

TEM sample preparation of wear-tested room-temperature pulsed-laser-deposited thin films of MoS2 by ultramicrotomy

1993 ◽  
Vol 51 ◽  
pp. 1118-1119
Author(s):  
Pamela F. Lloyd ◽  
Scott D. Walck
Keyword(s):  
Thin Films ◽  
Sample Preparation ◽  
Room Temperature ◽  
High Vacuum ◽  
Pulsed Laser ◽  
Ultra High Vacuum ◽  
Wear Testing ◽  
Preparation Technique ◽  
Cross Sectional ◽  
Aerospace Applications

Pulsed laser deposition (PLD) is a novel technique for the deposition of tribological thin films. MoS2 is the archetypical solid lubricant material for aerospace applications. It provides a low coefficient of friction from cryogenic temperatures to about 350°C and can be used in ultra high vacuum environments. The TEM is ideally suited for studying the microstructural and tribo-chemical changes that occur during wear. The normal cross sectional TEM sample preparation method does not work well because the material’s lubricity causes the sandwich to separate. Walck et al. deposited MoS2 through a mesh mask which gave suitable results for as-deposited films, but the discontinuous nature of the film is unsuitable for wear-testing. To investigate wear-tested, room temperature (RT) PLD MoS2 films, the sample preparation technique of Heuer and Howitt was adapted.Two 300 run thick films were deposited on single crystal NaCl substrates. One was wear-tested on a ball-on-disk tribometer using a 30 gm load at 150 rpm for one minute, and subsequently coated with a heavy layer of evaporated gold.

Pulsed laser deposition of PbMg1/3Nb2/3O3 thin films and PbMg1/3Nb2/3O3/PbTiO3 multilayers

2001 ◽  
Vol 11 (PR11) ◽  
pp. Pr11-65-Pr11-69
Author(s):  
N. Lemée ◽  
H. Bouyanfif ◽  
J. L. Dellis ◽  
M. El Marssi ◽  
M. G. Karkut ◽  
...  
Keyword(s):  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Pulsed Laser ◽  
Laser Deposition

SrBi2Nb2O9 ferroelectric thin films deposited by pulsed laser deposition on textured and epitaxied platinum electrodes

2001 ◽  
Vol 11 (PR11) ◽  
pp. Pr11-133-Pr11-137
Author(s):  
J. R. Duclère ◽  
M. Guilloux-Viry ◽  
A. Perrin ◽  
A. Dauscher ◽  
S. Weber ◽  
...  
Keyword(s):  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Pulsed Laser ◽  
Ferroelectric Thin Films ◽  
Laser Deposition ◽  
Platinum Electrodes
Sign in / Sign up

Export Citation Format

Share Document