Technical Paper Response: Determination of Manufacturing Cycle Time in Multi‐stage Production Systems

1989 ◽  
Vol 9 (3) ◽  
pp. 60-63 ◽  
Author(s):  
S.K. Goyal ◽  
S. Singhal
2006 ◽  
Vol 145 (1) ◽  
pp. 51-68 ◽  
Author(s):  
Boaz Golany ◽  
Steven T. Hackman ◽  
Ury Passy

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Jagan Mohan Reddy K. ◽  
Neelakanteswara Rao A. ◽  
Krishnanand Lanka ◽  
PRC Gopal

Purpose Pull production systems have received much attention in the supply chain management environment. The number of Kanbans is a key decision variable in the pull production system as it affects the finished goods inventory (FGI) and backorders of the system. The purpose of this study is to compare the performance of the fixed and dynamic Kanban systems in terms of operational metrics (FGI and backorders) under the demand uncertainty. Design/methodology/approach In this paper, the system dynamics (SD) approach was used to model the performance of fixed and dynamic Kanban based production systems. SD approach has enabled the feedback mechanism and is an appropriate tool to incorporate the dynamic control during the simulation. Initially, a simple Kanban based production system was developed and then compared the performance of production systems with fixed and dynamic controlled Kanbans at the various demand scenarios. Findings From the present study, it is observed that the dynamic Kanban system has advantages over the fixed Kanban system and also observed that the variation in the backorders with respect to the demand uncertainty under the dynamic Kanban system is negligible. Research limitations/implications In a just-in-time production system, the number of Kanbans is a key decision variable. The number of Kanbans is mainly depended on the demand, cycle time, safety stock factor (SSF) and container size. However, this study considered only demand uncertainty to compare the fixed and dynamic Kanban systems. This paper further recommends researchers to consider other control variables which may influence the number of Kanbans such as cycle time, SSF and container size. Originality/value This study will be useful to decision-makers and production managers in the selection of the Kanban systems in uncertain demand applications.


2016 ◽  
Author(s):  
Abdulaha-Al Baquy ◽  
Jiu-Yu Li ◽  
Chen-Yang Xu ◽  
Khalid Mehmood ◽  
Ren-Kou Xu

Abstract. Soil acidity has become a serious constraint in dry land crop production systems of acidic Ultisols in tropical and subtropical regions of southern China, where winter wheat and canola are cultivated as important rotational crops. Regardless of other common existing concerns in acidic Ultisols of southern China, it needs to be investigated whether soil acidity has any effect on wheat and canola growth. There is little information on the determination of critical soil pH as well as aluminium (Al) concentration for wheat and canola crops. The objective of this study was to determine the critical soil pH and exchangeable aluminium concentration (AlKCl) for wheat and canola production. Two pot cultures with two Ultisols from Hunan and Anhui were conducted for wheat and canola crops in a controlled growth chamber, with a completely randomized design. A soil pH gradient ranging from 3.7 (Hunan) and 3.97 (Anhui) to 6.5, with three replications, was used as a treatment. Aluminium sulfate (Al2(SO4)3) and hydrated lime (Ca(OH)2) were used to obtain the target soil pH levels. Plant height, shoot dry weight, root dry weight, and chlorophyll content (SPAD value) of wheat and canola were adversely affected by soil acidity in both locations. The critical soil pH and AlKCl of the Ultisol from Hunan for wheat were 5.29 and 0.56 cmol kg−1, respectively. At Anhui, the threshold soil pH and AlKCl for wheat were 4.66 and 2.36 cmol kg−1, respectively. On the other hand, the critical soil pH for canola was 5.65 and 4.87 for the Ultisols from Hunan and Anhui, respectively. The critical soil exchangeable Al for canola cannot be determined from the experiment of this study. The results suggested that the critical soil pH and AlKCl varied between different locations for the same variety of crop, due to the different soil types and their other soil chemical properties. The critical soil pH for canola was higher than that for wheat for both Ultisols, thus canola was more sensitive to soil acidity. Therefore, we recommend that liming should be undertaken to increase soil pH if it falls below these critical soil pH levels for wheat and canola production.


2018 ◽  
Vol 67 (4) ◽  
pp. 494-500
Author(s):  
Luiz Alberto Silva Rodrigues Pinto ◽  
Octávio Vioratti Telles Mendonça ◽  
Celeste Queiroz Rossi ◽  
Marcos Gervasio Pereira ◽  
Fabiana Costa Barros

Determination of mineralizable carbon (C) is based on the evolution of C-CO2, reflecting the activity of soil biota in soil organic matter (SOM) decomposition, and can be used as a testing parameter in agroecological production systems. The objective of the present work was to quantify mineralizable C in aggregates of different biogenic and physiogenic formation pathways in agroecological management systems in the city of Seropédica, state of Rio de Janeiro. Five sampling areas were selected: (1) 10-year agroforestry system (AFS), (2) 15-year full sun coffee (C-SUN), (3) 15-year shaded coffee (C-SHA), (4) 10-year phlegm alleles (FLE), and (5) 6-year no-till planting system with corn and eggplant (NT) in Red-Yellow Argissolo in Seropédica-RJ.Morphological patterns were used to identify the formation pathway (biogenic and physiogenic) of aggregates.  In these, fertility, total organic carbon (TOC), and total nitrogen (TN) were evaluated.  The evolution and accumulation of C-CO2were determined in the laboratory after 35 days of incubation. The NT area under agroecological management present higher C-CO2 accumulation between the systems with biogenic aggregates and less accumulation in the physiogenic aggregates. 


2020 ◽  
Vol 110 (05) ◽  
pp. 295-298
Author(s):  
Christian Brecher ◽  
Florian Kneer ◽  
Stephan Neus

Die axiale Steifigkeit von Kugelgewindetrieben ist wesentlich für das Betriebsverhalten von Werkzeugmaschinen. Während der Bearbeitung werden die Prozesskräfte über den Kugelgewindetrieb in die Maschinenstruktur übertragen. Kugelgewindetriebe tragen daher maßgeblich zur Qualität und Produktivität von Werkzeugmaschinen bei. Dieser Beitrag beschreibt eine Methode zur messtechnischen, prüfstandsgebundenen Ermittlung des Last-Verlagerungsverhaltens an Kugelgewindetrieben.   The axial elastic displacement of ball screws are essential for the operating behavior of machine tools. During machining, process forces must be transmitted to the machine structure via the ball screw. Ball screws contribute significantly to the quality and productivity of machine tools. This technical paper describes a methodology for the metrological determination of the load-displacement behavior on ball screws.


Sign in / Sign up

Export Citation Format

Share Document