The Design of Microcomputer Automatic Strip Material Cutter

2012 ◽  
Author(s):  
Hai-bo Lin
Keyword(s):  
Strip Material

Selection of Turbine Seal Strip Material by MCDM Approach

2021 ◽  
pp. 331-338
Author(s):  
Shwetank Avikal ◽  
Akhilesh Sharma ◽  
Anup Kumar Mishra ◽  
Rohit Singh ◽  
Amit Kumar Singh ◽  
...  
Keyword(s):  
Strip Material ◽  
Selection Of

Lamb waves for inspection of commercially rolled hot strip material

1976 ◽  
Vol 9 (1) ◽  
pp. 13-15 ◽  
Author(s):  
D.F. Ball ◽  
D. Shewring
Keyword(s):  
Lamb Waves ◽  
Strip Material ◽  
Hot Strip

scholarly journals Research on the PLC-based Full-automatic Punching Machine for Transformer Insulating Strip Material

2016 ◽  
Author(s):  
Lijun Xu ◽  
Youlian Duan ◽  
Jiwei Wang ◽  
Xiaojing Hou
Keyword(s):  
Strip Material

An Experimental Study of a Plasto-Hydrodynamic Strip Drawing Process

1989 ◽  
Vol 203 (1) ◽  
pp. 57-65 ◽  
Author(s):  
A H Memon ◽  
G R Symmons ◽  
R Crampton ◽  
M S J Hashmi
Keyword(s):  
Critical Shear Stress ◽  
Polymer Melt ◽  
Hydrodynamic Pressure ◽  
Drawing Process ◽  
Copper Strip ◽  
Melt Temperature ◽  
Strip Material ◽  
Strip Drawing ◽  
Converging Flow ◽  
Reduction In Area

Experimental results are presented for a new dieless strip drawing process in which conventional wedge-shaped dies have been replaced by a reduction unit having a stepped rectangular cavity. The smallest cavity dimensions are larger than those of the incoming strip, thus eliminating the problem of die friction and consequential tool wear. In this novel process, the strip is passed through a chamber filled with polymer melt and then pulled through the reduction unit. The strip material is deformed due to the combined effects of shear drag and the hydrodynamic pressure generated by the converging flow of the polymer melt. Experiments were carried out in which the process parameters such as the unit geometry, speed and polymer melt temperature and hence viscosity were varied and the hydrodynamic pressure, reduction in strip size and drawing load were measured. Initial experiments were carried out by using copper strip and low-density polyethylene at two different melt temperatures. Results from experiments showed that a reduction in area of strip of more than 10 per cent could be achieved in a single pass. The Newtonian analysis presented by the authors in reference (9) is modified to incorporate the critical shear stress limit of the polymer melt and the non-linear strain-hardening property of the strip material.

Effect of the cold-rolling parameters and the yield strength of the strip material on the friction stresses in a deformation zone

2009 ◽  
Vol 2009 (5) ◽  
pp. 400-405
Author(s):  
E. A. Garber ◽  
I. V. Yagudin ◽  
V. V. Ermilov ◽  
A. I. Traino
Keyword(s):  
Yield Strength ◽  
Cold Rolling ◽  
Deformation Zone ◽  
Strip Material

Bendability of Strip Material: A Key Issue for Connector Applications

Copper ◽  
2007 ◽  
pp. 211-216
Author(s):  
Isabell Buresch ◽  
Uwe Hofmann ◽  
Stefan Theobald
Keyword(s):  
Strip Material

scholarly journals Ultrasonic examination of JBK-75 strip material

1982 ◽  
Author(s):  
K. V. Cook ◽  
R. A. Cunningham, Jr. ◽  
J. C. Lewis ◽  
R. W. McClung
Keyword(s):  
Ultrasonic Examination ◽  
Strip Material
Sign in / Sign up

Export Citation Format

Share Document