yield strength
Recently Published Documents


TOTAL DOCUMENTS

3427
(FIVE YEARS 803)

H-INDEX

67
(FIVE YEARS 10)

2022 ◽  
Vol 6 (1) ◽  
Author(s):  
Michael R. Fellinger ◽  
Louis G. Hector ◽  
Dallas R. Trinkle

Author(s):  
Bo Pu ◽  
Ping Song ◽  
Wen-bin Li ◽  
Wen-jin Yao ◽  
Xiao-ming Wang

Abstract This paper presents a study on plastic deformation behavior of Cu–50Ta alloy at temperatures of 286–473 K and strain-rate of 0.01–6200 s−1. The effects of temperature, strain-rate, and strain on the yield strength, flow stress, and strain-rate sensitivity coefficient were determined. A phenomenological model was established to predict variation of the strain-rate sensitivity coefficient for Cu–50Ta alloy under dynamic compression. A Johnson–Cook constitutive model was established to predict the equivalent stress–equivalent plastic strain relationship under extreme deformation (high temperature and strain-rate). The results showed that the plastic deformation behavior of Cu–50Ta alloy was affected by temperature, strain-rate, and strain. The material exhibited obvious strain-rate strengthening and thermal softening. As the strain-rate increased, the yield strength logarithmically increased. At a temperature of 286 K, the strain-rate increased from 0.01 s−1 to 6200 s−1, and the yield strength increased from 543.75 MPa to 881.13 MPa. In addition, the yield strength linearly decreased as the deformation temperature increased. Under conditions of dynamic deformation, the variation of strain-rate sensitivity coefficient could be expressed as a function of strain-rate and strain. The phenomenological model accurately described the variation of the strain-rate sensitivity coefficient of Cu–50Ta under dynamic deformation conditions. The Johnson–Cook constitutive parameters, calibrated by experimental data, described the plastic deformation behavior of the alloy under high-velocity impact.


Author(s):  
Swaminathan Ganesan ◽  
Sampath Vedamanickam

In this study, the influence of upper cycle temperature (maximum temperature in a cycle) and the magnitude of applied stress on the functional properties of an SMA during partial thermomechanical cycling has been studied. A near-equiatomic NiTi SMA was chosen and tested under different upper cycle temperatures (between martensite finish (Mf) and austenite finish (Af) temperatures) and stress level (below and above the yield strength of the martensite). The upper cycle temperature was varied by controlling the magnitude of the current supply. The results show that a raise in the upper cycle temperature causes the permanent strain to increase and also lowers the stability. However, decreasing the stress imposed to a value lower than the yield strength of the martensite improves cyclic stability. The upper cycle temperature was found to influence the crack nucleation, whereas the applied stress level the crack propagation during partial thermomechanical cycling of SMAs. Therefore, decreasing the upper cycle temperature as well as the magnitude of stress applied to lower than the yield stress of martensite have been found to be suitable strategies for increasing the lifespan of SMA-based actuators during partial thermomechanical cycling.


Author(s):  
D N Ingle ◽  
M E Porter

Abstract Since their appearance in the fossil record 34 Mya, modern cetaceans (dolphins, whales, and porpoises) have radiated into diverse habitats circumglobally, developing vast phenotypic variations among species. Traits such as skeletal morphology and ecologically-linked behaviors denote swimming activity; trade-offs in flexibility and rigidity along the vertebral column determine patterns of caudal oscillation. Here, we categorized 10 species of cetaceans (Families Delphinidae and Kogiidae; N = 21 animals) into functional groups based on vertebral centra morphology, swimming speeds, diving behavior, and inferred swimming patterns. We quantified trabecular bone mechanical properties (yield strength, apparent stiffness, and resilience) among functional groups and regions of the vertebral column (thoracic, lumbar, and caudal). We extracted 6 mm3 samples from vertebral bodies and tested them in compression in three orientations (rostrocaudal, dorsoventral, and mediolateral) at 2 mm min−1. Overall, bone from the pre-fluke/fluke boundary had the greatest yield strength and resilience, indicating that the greatest forces are translated to the tail during caudal oscillatory swimming. Group 1, composed of five shallow-diving delphinid species, had the greatest vertebral trabecular bone yield strength, apparent stiffness, and resilience of all functional groups. Conversely, Group 3, composed of two deep-diving kogiid species, had the least strong, stiff, and resilient bone, while Group 2 (three deep-diving delphinid species) exhibited intermediate values. These data suggest that species that incorporate prolonged glides during deep descents in the water column actively swim less, and place relatively smaller loads on their vertebral columns, compared with species that execute shallower dives. We found that cetacean vertebral trabecular bone properties differed from the properties of terrestrial mammals; for every given bone strength, cetacean bone was less stiff by comparison. This relative lack of material rigidity within vertebral bone may be attributed to the non-weight bearing locomotor modes of fully aquatic mammals.


2022 ◽  
Vol 60 (1) ◽  
pp. 83-93
Author(s):  
Young-We Kim ◽  
Yong-Hee Jo ◽  
Yun-Soo Lee ◽  
Hyoung-Wook Kim ◽  
Je-In Lee

The effects of dissolution of the η′ phase by solution treatment on the mechanical properties of A7075-T6 alloy were investigated. Immediately after solution treatment of the T6 sheet at 450 oC or higher, elongation significantly increased and dissolution of the η′ phase occurred. η′ is the main hardening phase. After natural-aging, GPI, which is coherent with the aluminum matrix, was formed and strength increased. When bake hardening after natural-aging was performed, the yield strength slightly increased due to partial dissolution of the GPI and re-precipitation of the η′ phase. In contrast, after solution treatment at 400 oC, there was less elongation increase due to the precipitation of the coarse η phase at grain boundaries and low dissolution of the η′ phase. In addition, when bake hardening after natural-aging was performed, the yield strength decreased due to insufficient GPI, which is the nucleation site of the η′ phase. To promote reprecipitation of the η′ phase, the solution treatment temperature was set to a level that would increase solubility. As a result, the yield strength was significantly increased through re-precipitation of a large number of fine and uniform η′ phase. In addition, to increase the effect of dissolution, a pre-aging treatment was introduced and the bake hardenability can be improved after dissolution.


Gels ◽  
2022 ◽  
Vol 8 (1) ◽  
pp. 39
Author(s):  
Varuzhan Sarkisyan ◽  
Roman Sobolev ◽  
Yuliya Frolova ◽  
Irina Vorobiova ◽  
Alla Kochetkova

Beeswax and beeswax hydrocarbon-based oleogels were studied to evaluate the quantitative relationship between their yield strength and crystal size distribution. With this aim, oleogels were prepared using four different cooling regimes to obtain different crystal size distributions. The microstructure was evaluated by polarized light microscopy. The yield strength is measured by the cone penetration test. Oleogels were characterized by average grain size, microstructure entropy, grain boundary energy per unit volume, and microstructure temperature. We have provided the theoretical basis for interpreting the microstructure and evaluating the microstructure-based hardening of oleogels. It is shown that the microstructure entropy might be used to predict the yield strength of oleogels by the Hall-Petch relationship.


Author(s):  
Luosheng Ma ◽  
Lili Ma ◽  
Peipeng Jin ◽  
Xinya Feng ◽  
Lei Jia

Abstract In this study, ZK60 Mg alloys were prepared via hot-press sintering under a constant pressure of 30 MPa as well as Ar atmosphere. The sintering temperature was determined to be in the range of 450–600 °C with an interval of 50 °C. The effect of sintering temperature on the microstructures and mechanical properties of the alloys was investigated. All the four sintered alloys mainly exhibited an α-Mg-phase structure and equiaxed grain microstructure. However, a specific amount of melt, enriched in Zn element, formed when the sintering temperature reached 500 °C. Thus, only the alloy sintered at 450 °C maintained the nominal composition of the alloy powder, and exhibited the favorable yield strength and hardness, which was 135.1 MPa and 57 HV, respectively. The alloys sintered at 550 °C and 600 °C exhibited a reduced yield strength and hardness due to the loss of Zn element.


Buildings ◽  
2022 ◽  
Vol 12 (1) ◽  
pp. 41
Author(s):  
Moo-Won Hur ◽  
Yonghun Lee ◽  
Min-Jun Jeon ◽  
Sang-Hyun Lee

In this study, the Kagome truss damper, a metallic wire structures, was introduced and its mechanical properties were investigated through theoretical analyses and experimental tests. The yield strength of the Kagome damper is dependent on the geometric shape and diameter of the metallic wire. The Kagome damper has higher resistance to plastic buckling as well as lower anisotropy. Cyclic shear loading tests were conducted to investigate the energy dissipation capacity and stiffness/strength degradation by repeated loadings. The hysteretic properties obtained from the tests suggest that a modification of the ideal truss model with a hinged connection could be used to predict the yield strength and stiffness of the damper. For seismic retrofitting of a low-rise RC moment frame system, a wall-type Kagome damping system (WKDS) was proposed. The effectiveness of the proposed system was verified by conducting cyclic loading tests using a RC frame with/without the WKDS (story drift ratio limit 1.0%). The test results indicated that both the strength and stiffness of the RC frame increased to the target level and that its energy dissipation capacity was significantly enhanced. Nonlinear static and dynamic analyses were carried out to validate that the existing building structure can be effectively retrofitted using the proposed WKDS.


Materials ◽  
2022 ◽  
Vol 15 (1) ◽  
pp. 355
Author(s):  
Ao Fu ◽  
Yuankui Cao ◽  
Yuxi Liu ◽  
Shenghang Xu

A series of novel lightweight TaNbVTi-based refractory high entropy alloys (RHEA) were fabricated through ball-milling and spark plasma sintering (SPS). The reinforced phase of TiO precipitates were in-situ formed due to the introduction of Al2O3 ceramic particles. The RHEA with 15% Al2O3 exhibits a high compressive yield strength (1837 MPa) and a low density (7.75 g/cm3) with an adequate ductility retention. The yield strength and density are 32% higher and 15% lower, respectively, compared to the RHEA without Al2O3 addition. The specific yield strength (237 MPa cm3/g) of the RHEAs is much higher than that of other reported RHEAs, and is mainly ascribed to the introduction of high volume fraction of Al2O3 additives, resulting in solid solution strengthening and precipitation strengthening. Meanwhile, the ductile matrix is responsible for the good compressive plasticity.


Sign in / Sign up

Export Citation Format

Share Document