Electromagnetic Interference Measurements of Fluorescent Lamps Operated with Solid-State Ballasts

1982 ◽  
Vol IA-18 (6) ◽  
pp. 647-652 ◽  
Author(s):  
Allan A. Arthur ◽  
Rudolph R. Verderber ◽  
Francis Rubinstein ◽  
Oliver C. Morse
Keyword(s):  
Solid State ◽  
Electromagnetic Interference ◽  
Fluorescent Lamps ◽  
Interference Measurements

Preparation and Luminescence Property of LaMgAl11O19

2012 ◽  
Vol 519 ◽  
pp. 224-227 ◽  
Author(s):  
Xin Min ◽  
Ming Hao Fang ◽  
Yan Gai Liu ◽  
Zhao Hui Huang
Keyword(s):  
Solid State ◽  
Luminescence Property ◽  
Broad Band ◽  
Emission Spectra ◽  
Synthesis Temperature ◽  
Solid State Lasers ◽  
Broad Band Emission ◽  
Band Emission ◽  
Air Atmosphere ◽  
Fluorescent Lamps

Lanthanum magnesium hexaaluminate (LaMgAl11O19, LMA) has attracted much interest as its widely used in solid state lasers, TV phosphors and fluorescent lamps. In this paper, LaMgAl11O19 ceramic was pressureless sintered at 1650 °C for 10 h in air atmosphere using LaMgAl11O19 powders prepared by solid-state reaction at 1500 °C for 4 h. The result indicated that the synthesis temperature of LaMgAl11O19 powders was about 1500 °C. The LMA ceramic sample was dense and had a microstructure of platelet-like gains. The excitation spectrum shows two wide bands with the peaks at about 254 nm and 265 nm by monitoring the strongest 362 nm emission, and the emission spectra is consisted of a broad band emission with their peaks near 362 nm with a half-width about 5 nm exciting with 265 nm wavelength.

Electromagnetic Interference Measurements at 900 MHZ on 230-KV and 500-KV Transmission Lines

1986 ◽  
Vol 1 (2) ◽  
pp. 140-149 ◽  
Author(s):  
V. L. Chartier ◽  
R. Sheridan ◽  
J. N. DiPlacido ◽  
M. O. Loftness
Keyword(s):  
Transmission Lines ◽  
Electromagnetic Interference ◽  
Interference Measurements

scholarly journals The light color quality of LED operating at winter temperatures

2019 ◽  
Vol 11 (4) ◽  
pp. 112 ◽  
Author(s):  
Przemysław Tabaka ◽  
Pawel Rozga
Keyword(s):  
Solid State ◽  
Operating Temperature ◽  
Solid State Lighting ◽  
Light Sources ◽  
Led Light ◽  
Fluorescent Lamps ◽  
Color Rendering ◽  
Incandescent Lamps ◽  
Colour Rendering

The paper presents the results of calculations of colorimetric parameters of LED sources operating at a temperature range from -25oC to 25oC. The chromaticity coordinates and color rendition quality parameters were calculated on the basis of registered spectral distributions of radiation. For individual LED chromaticity shift is illustrated at CIE 1931 x,y diagram with 3 step and 7 step MacAdam ellipses. Full Text: PDF ReferencesJ. P. Freyssinier, D. Frering, J. Taylor, N. Narendran, and P. Rizzo, Reducing lighting energy use in retail display windows. Sixth International Conference on Solid State Lighting, Proceedings of SPIE 6337, 63371L (2006). CrossRef Aman, M. M., et al., 2013. Analysis of the performance of domestic lighting lamps, Energy Policy, CrossRef E. Elijošiute, J. Balciukevičiute, G. Denafas, Life cycle assessment of; compact fluorescent and incandescent lamps: Comparative analysis. Environ Res. Eng. Manag. 61 (3), pp. 65-72, (2012), CrossRef D. Czyzewski, LED substitutes of conventional incandescent lamps Przeglad Elektrotechniczny R. 88, No. 11 (2012), CrossRef P. Tabaka, P. Rozga, Assessment of methods of marking LED sources with the power of equivalent light bulb, ulletin of the Polish Academy of Sciences. Technical Sciences, Vol. 65, No. 6, (2017) CrossRef I. Fryc, P. Jakubowski, K. Kołacz, Analysis of optical radiation parameters of compact discharge HID lamps and LED COB modules used for illuminating shop windows, Przeglad Elektrotechniczny,R. 93, No 11, (2017); pp. 186-189, CrossRef T. Kawabata, Y. Ohno; Optical measurements of OLED panels for lighting applications, pp 1176-1186 Jun 2013, Journal of Modern Optics, Vol. 60, 2013 Issue 14 CrossRef W. Żagan, Conditions necessary to replacing the conventional lamps by energy-saving lamps, Przeglad Elektrotechniczny R. 85, No. 5, pp. 100-104, (2009). DirectLink P. Tabaka; Influence of Ambient Temperature on Colour Properties of Low-Pressure Fluorescent Lamps, Light & Engineering, Vol. 23; No. 2; (2015). DirectLink W. R. Ryckaert, et al., Linear LED tubes versus fluorescent lamps: An evaluation. Energy Build. 49, pp. 429-436. CrossRef M. Zalesinska, J. Zablocka, K. Wandachowicz, Evaluation of Selected Parameters of Non-Directional Household Lamps, Conference: 2018 VII. Lighting Conference of the Visegrad Countries (Lumen V4), CrossRef I. Fryc; Measurement techniques of optical LEDs properties performed with compliance conformity with CIE 127:2007 standard, Przeglad Elektrotechniczny R. 85, No. 11, pp. 317-319, (2009) DirectLink IESNA, IES Approved Method: Measuring Lumen Maintenance of LED Light Sources. IES LM-80-08', IES Subcommittee on Solid-State Lighting of the IES Testing Procedures Committee (2018). DirectLink D. B. Judd, Estimation of chromaticity differences and nearest color temperature on the standard 1931 ICI colorimetric coordinate system. J. Opt. Soc. America 26 (11), 421, (1936) CrossRef CIE 177:2007 Colour Rendering of White LED Light Sources DirectLink CIE 13.3-1995 Method of Measuring and Specifying Colour. DirectLink CIE 224:2017 Colour Fidelity Index for accurate scientific use DirectLink CIE 15:2004 Colorimetry. DirectLink D. Mozysrska, M. Wyrwas, I. Fryc, The determination of the LEDs colorimetric parameters, in the range of their operating temperature, Przeglad Elektrotechniczny, R. 93, No. 4a, pp. 232-234, (2012). DirectLink J. Kowalska, Analysis of parameters describing the quality of the color rendering of light sources according to the IES TM-30-15 and the CIE 013.3-1995, Przeglad Elektrotechniczny, R. 93, No. 6; pp. 50-54, (2017) CrossRef J. Kowalska, I. Fryc, Colour rendition quality of typical fluorescent lamps determined by CIE Colour Fidelity Index and Colour Rendering Index, Przeglad Elektrotechniczny, R. 95, No. 7; (2019), pp. 94-97 CrossRef J. Kowalska, Ambiguity and limitations in determining the quality of the color rendering of light sources by index Ra (CIE CRI), Przeglad Elektrotechniczny, R. 93 No. 5, pp. 74-78, (2017) CrossRef I. Fryc, J. Fryc, A. Wasowski, Considerations about determining color rendering of light sources, Przeglad Elektrotechniczny, R. 92 No. 2, pp. 218-223, (2016) CrossRef I. Fryc, LED's spectral power distribution under different condition of operating temperature and driving current, Przeglad Elektrotechniczny, R. 86, No. 10, pp. 187-189, (2010). DirectLink A. David, P. Fini, K. Houser et al., Development of the IES method for evaluating the color rendition of light sources, Optics Express; Vol. 23; Issue 12, pp. 15888-15906, (2015). CrossRef K. Houser, M. Mossman, K. Smet et al, Tutorial, Color Rendering and Its Applications in Lighting, LEUKOS; Vol. 12, Issue 1-2; pp. 7-26; (2016). CrossRef

scholarly journals Shedding Light on the Anthropogenic Europium Cycle in the EU–28. Marking Product Turnover and Energy Progress in the Lighting Sector

Resources ◽  
2018 ◽  
Vol 7 (3) ◽  
pp. 59 ◽  
Author(s):  
Luca Ciacci ◽  
Ivano Vassura ◽  
Fabrizio Passarini
Keyword(s):  
Solid State ◽  
Energy Use ◽  
Sustainable Use ◽  
Environmental Benefits ◽  
Recycling Industry ◽  
Fluorescent Lamps ◽  
Lighting Systems ◽  
Phase Out ◽  
The Eu ◽  
State Technology

Phase-out strategies for incandescent bulbs in favor of advanced energy-efficiency lighting systems such as fluorescent lamps and solid-state technology have considerably reduced the energy use for lighting, but have also resulted in dependence on many critical materials like rare earth elements and shifted the attention to sustainable use and recovery of resources. In this work, a dynamic material flow model was developed to analyze the socio-economic metabolism of europium in the EU–28. The analysis shows that europium marked product turnover and progress in lighting efficiency, with this element being employed both in traditional and novel lighting technology to provide luminescence. The results also demonstrate that the current anthropogenic reserve could constitute an attractive source of secondary europium with substantial potentials for environmental benefits. However, nonexistent recycling and market forces hinder strategies for material circularity. In particular, the transition from fluorescent lamps to solid-state technology is quickly decreasing the demand for europium. This trend adds further constraints to the creation of a sustainable recycling industry for europium, with primary sources that might remain the preferable route to supply phosphors to future lighting systems.

Sign in / Sign up

Export Citation Format

Share Document