On the Applicability of Acoustoelasticity for Residual Stress Determination

1981 ◽  
Vol 48 (4) ◽  
pp. 791-795 ◽  
Author(s):  
G. C. Johnson
Keyword(s):  
Residual Stress ◽  
Plastic Deformation ◽  
Stress State ◽  
Aluminum Alloys ◽  
Nondestructive Evaluation ◽  
Theoretical Development ◽  
Stress Determination ◽  
Acoustic Response ◽  
Residual Stress Determination ◽  
Residual Stress State

Acoustoelasticity has recently been used for the nondestructive evaluation of residual stresses. In making such measurements the assumption has been made that the plastic flow leading to the residual stress state did not change the acoustic response of the material. This paper examines the extent to which that assumption holds for three aluminum alloys. The acoustoelastic theory is summarized and results are presented for tests of specimens under uniaxial tension which are subjected to plastic deformation followed by complete unloading. It is shown that the assumption made does not hold for all materials and that further theoretical development is required for general quantitative residual stress determination.

scholarly journals Influence of Steel Grain Size on Residual Stress in Grinding Processing

2010 ◽  
Vol 638-642 ◽  
pp. 2389-2394 ◽  
Author(s):  
Masahide Gotoh ◽  
Katsuhiro Seki ◽  
M. Shozu ◽  
Hajime Hirose ◽  
Toshihiko Sasaki
Keyword(s):  
Mechanical Properties ◽  
Residual Stress ◽  
Grain Size ◽  
Stress State ◽  
Mechanical Grinding ◽  
Fine Grained ◽  
Residual Stress State ◽  
Analysis Methods ◽  
Average Grain Size ◽  
Fine Grained Steels

The fine-grained rolling steels NFG600 and the conventional usual rolling steels SM490 were processed by sand paper polishing and mechanical grinding to compare the residual stress generated after processing. The average grain size of NFG600 and SM490 is 3 μm and 15μm respectively. Therefore improvement of mechanical properties for such fine-grained steels is expected, it is important to understand the residual stress state of new fine-grained materials with processing. In this study, multi axial stresses of two kinds of specimens after polishing and grinding were measured by three kinds of analysis methods including cos-ψ method. As a result, as for σ33, the stress of NFG was compression, though that of SM490 was tension.

About Residual Stress State of Castings: The Case of HPDC Parts and Possible Advantages through Semi-Solid Processes

2022 ◽  
Vol 327 ◽  
pp. 272-278
Author(s):  
Elisa Fracchia ◽  
Federico Simone Gobber ◽  
Claudio Mus ◽  
Yuji Kobayashi ◽  
Mario Rosso
Keyword(s):  
Residual Stress ◽  
Stress State ◽  
Residual Stresses ◽  
Casting Process ◽  
Ray Method ◽  
Premature Failure ◽  
Thin Walls ◽  
Residual Stress State ◽  
Semi Solid ◽  
Pressure Die Casting

Nowadays, one of the most crucial focus in the aluminium-foundry sector is the production of high-quality castings. Mainly, High-Pressure Die Casting (HPDC) is broadly adopted, since by this process is possible to realize aluminium castings with thin walls and high specific mechanical properties. On the other hand, this casting process may cause tensile states into the castings, namely residual stresses. Residual stresses may strongly affect the life of the product causing premature failure of the casting. Various methods can assess these tensile states, but the non-destructive X-Ray method is the most commonly adopted. Namely, in this work, the residual stress analysis has been performed through Sinto-Pulstec μ-X360s. Detailed measurements have been done on powertrain components realized in aluminium alloy EN AC 46000 through HPDC processes to understand and prevent dangerous residual stress state into the aluminium castings. Furthermore, a comparison with stresses induced by Rheocasting processes is underway. In fact, it is well known that Semi-Solid metal forming combines the advantages of casting and forging, solving safety and environmental problems and possibly even the residual stress state can be positively affected.

Sign in / Sign up

Export Citation Format

Share Document