Detached Eddy Simulation of Transition in Turbomachinery: Linear Compressor Cascade

2021 ◽  
pp. 1-10
Author(s):  
Zifei Yin ◽  
Paul Durbin
Keyword(s):  
Boundary Layer ◽  
Large Scale ◽  
Separated Flow ◽  
Adaptive Model ◽  
Detached Eddy Simulation ◽  
Compressor Cascade ◽  
Linear Compressor ◽  
Eddy Simulation ◽  
Delayed Detached Eddy Simulation ◽  
Linear Compressor Cascade

Abstract The adaptive, l2-omega delayed detached eddy simulation model was selected to simulate the flow in the V103 linear compressor cascade. The Reynolds number based on axial chord length is 138,500. Varies inflow turbulent intensities from 0% to 10% were tested to evaluate the performance of the adaptive model. The adaptive model is capable of capturing the laminar boundary layer and the large scale perturbations inside it. The instability of large scale disturbances signals the switch to a hybrid simulation of turbulent boundary layer -- the transition front is thus predicted. In the case of separation-induced transition, the adaptive model, which uses eddy simulation in separated flow, can predict the separation bubble size accurately. Generally, the adaptive, delayed detached eddy simulation model can simulate the transitional separated flow in a linear compressor cascade, with a correct response to varying turbulent intensities.

Numerical Investigation of Intermittent Corner Separation in a Linear Compressor Cascade

2016 ◽  
Author(s):  
Wei Ma ◽  
Feng Gao ◽  
Xavier Ottavy ◽  
Lipeng Lu ◽  
A. J. Wang
Keyword(s):  
Flow Field ◽  
Large Scale ◽  
Leading Edge ◽  
Suction Side ◽  
Detached Eddy Simulation ◽  
Compressor Cascade ◽  
Linear Compressor ◽  
Corner Separation ◽  
Eddy Simulation ◽  
Linear Compressor Cascade

Recently bimodal phenomenon in corner separation has been found by Ma et al. (Experiments in Fluids, 2013, doi:10.1007/s00348-013-1546-y). Through detailed and accurate experimental results of the velocity flow field in a linear compressor cascade, they discovered two aperiodic modes exist in the corner separation of the compressor cascade. This phenomenon reflects the flow in corner separation is high intermittent, and large-scale coherent structures corresponding to two modes exist in the flow field of corner separation. However the generation mechanism of the bimodal phenomenon in corner separation is still unclear and thus needs to be studied further. In order to obtain instantaneous flow field with different unsteadiness and thus to analyse the mechanisms of bimodal phenomenon in corner separation, in this paper detached-eddy simulation (DES) is used to simulate the flow field in the linear compressor cascade where bimodal phenomenon has been found in previous experiment. DES in this paper successfully captures the bimodal phenomenon in the linear compressor cascade found in experiment, including the locations of bimodal points and the development of bimodal points along a line that normal to the blade suction side. We infer that the bimodal phenomenon in the corner separation is induced by the strong interaction between the following two facts. The first is the unsteady upstream flow nearby the leading edge whose angle and magnitude fluctuate simultaneously and significantly. The second is the high unsteady separation in the corner region.

Adaptive Detached Eddy Simulation of End-Wall Flow in a Linear Compressor Cascade

2020 ◽  
Author(s):  
Zifei Yin
Keyword(s):  
Pressure Coefficient ◽  
Detached Eddy Simulation ◽  
Compressor Cascade ◽  
Local Flow ◽  
Linear Compressor ◽  
Eddy Simulation ◽  
Wall Flow ◽  
Linear Compressor Cascade ◽  
End Wall ◽  
Des Model

Abstract Delayed detached eddy simulations and wall-modeled eddy simulations using the adaptive DES model were performed to simulate corner separation in the Ecole Centrale de Lyon linear compressor cascade. The adaptive DES model directly uses length scale to define eddy viscosity, which makes it nature to compute the model constant CDES dynamically. The dynamic procedure adapts viscosity to local flow and grid. Delayed detached eddy simulations, with and without the dynamic procedure, were performed to demonstrate the benefit of adapting viscosity to local flow. Recycling method was adopted to generate inflow unsteady turbulent boundary layer for wall-modeled eddy simulations. The wall-modeled eddy simulation showed improvement over delayed-DES, in terms of static pressure coefficient around the blade and total pressure loss at downstream locations.

Assessment of DES Models for Separated Flow From a Hump in a Turbulent Boundary Layer

2009 ◽  
Vol 131 (11) ◽  
Author(s):  
Daniel C. Lyons ◽  
Leonard J. Peltier ◽  
Frank J. Zajaczkowski ◽  
Eric G. Paterson
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Mean Field ◽  
Separated Flow ◽  
Separation Point ◽  
Navier Stokes ◽  
Detached Eddy Simulation ◽  
Flow Solver ◽  
Eddy Simulation ◽  
Delayed Detached Eddy Simulation

Separated flow past a hump in a turbulent boundary layer is studied numerically using detached-eddy simulation (DES), zonal detached-eddy simulation (ZDES), delayed detached-eddy simulation (DDES), and Reynolds-averaged Navier–Stokes (RANS) modeling. The geometry is smooth so the separation point is a function of the flow solution. Comparisons to experimental data show that RANS with the Spalart–Allmaras turbulence model predicts the mean-field statistics well. The ZDES and DDES methods perform better than the DES formulation and are comparable to RANS in most statistics. Analyses motivate that modeled-stress depletion near the separation point contributes to differences observed in the DES variants. The order of accuracy of the flow solver ACUSOLVE is also documented.

Hybrid RANS/LES Simulation of Corner Stall in a Linear Compressor Cascade

2018 ◽  
Vol 140 (8) ◽  
Author(s):  
Guoping Xia ◽  
Gorazd Medic ◽  
Thomas J. Praisner
Keyword(s):  
Axial Flow ◽  
Leading Edge ◽  
Horseshoe Vortex ◽  
Special Treatment ◽  
Detached Eddy Simulation ◽  
Compressor Cascade ◽  
Data Set ◽  
Linear Compressor ◽  
Eddy Simulation ◽  
Linear Compressor Cascade

Current design-cycle Reynolds-averaged Navier–Stokes (RANS) based computational fluid dynamics (CFD) methods have the tendency to over-predict corner-stall events for axial-flow compressors operating at off-design conditions. This shortcoming has been demonstrated even in simple single-row cascade configurations. Here we report on the application of hybrid RANS/large eddy simulation (LES), or detached eddy simulation (DES), for simulating the corner-stall data from the linear compressor cascade work conducted at Ecole Centrale de Lyon. This benchmark data set provides detailed loss information while also revealing a bimodal behavior of the separation which, not surprisingly, is also not well modeled by RANS. The hybrid RANS/LES results presented here predict bimodal behavior similar to the data only when special treatment is adopted to resolve the leading-edge endwall region where the horseshoe vortex (HV) forms. The (HV) is shown to be unstable, which produces the bimodal instability. The DES simulation without special treatment or refinement in the HV region fails to predict the bimodal instability, and thus the bimodal behavior of the separation. This, in turn, causes a gross over-prediction in the scale of the corner-stall. The HV region is found to be unstable with rolling of the tertiary vortex (TV) over the secondary vortex and merging with the primary HV. With these flow dynamics realized in the DES simulations, the corner stall characteristics are found to be in better agreement with the experimental data, as compared to RANS and standard DES approaches.

Assessment of DES Models for Separated Flow From a Hump in a Turbulent Boundary Layer

2007 ◽  
Author(s):  
Daniel C. Lyons ◽  
Leonard J. Peltier ◽  
Frank J. Zajaczkowski ◽  
Eric G. Paterson
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Mean Field ◽  
Turbulence Models ◽  
Separated Flow ◽  
Navier Stokes ◽  
Detached Eddy Simulation ◽  
Eddy Simulation ◽  
Delayed Detached Eddy Simulation ◽  
Rans Modeling

Turbulent flow past the Glauert-Goldschmied body, a flow-control hump in a turbulent boundary layer, is studied numerically using detached-eddy simulation (DES), zonal detached-eddy simulation (ZDES), delayed detached-eddy simulation (DDES), and Reynolds-Averaged Navier-Stokes (RANS) modeling. The geometry is smooth so the downstream separation point is not set by facets of the geometry but is a function of the pressure gradient, a challenging condition for turbulence models. Comparisons to experimental data show that RANS with the Spalart-Allmaras turbulence model predicts the mean-field statistics well. The ZDES and DDES methods perform better than the DES formulation and are comparable to RANS in most statistics. An analysis of model behavior indicates that modeled stress depletion in the detached shear layer shortly after separation leads to loss of accuracy in the DES variants.

scholarly journals Large-eddy simulation of 3-D corner separation in a linear compressor cascade

2015 ◽  
Vol 27 (8) ◽  
pp. 085105 ◽  
Author(s):  
Feng Gao ◽  
Wei Ma ◽  
Gherardo Zambonini ◽  
Jérôme Boudet ◽  
Xavier Ottavy ◽  
...  
Keyword(s):  
Large Eddy Simulation ◽  
Compressor Cascade ◽  
Linear Compressor ◽  
Corner Separation ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Linear Compressor Cascade

Simulation of Dynamic Stall on an Elastic Rotor in High-Speed Turn Flight

2020 ◽  
Vol 65 (2) ◽  
pp. 1-12
Author(s):  
Johannes Letzgus ◽  
Manuel Keßler ◽  
Ewald Krämer
Keyword(s):  
High Speed ◽  
Separated Flow ◽  
Flight Test ◽  
Dynamic Stall ◽  
Minor Role ◽  
Detached Eddy Simulation ◽  
Rotor Aerodynamics ◽  
Eddy Simulation ◽  
Delayed Detached Eddy Simulation ◽  
A Minor

A highly loaded, high-speed turn flight of Airbus Helicopters' Bluecopter demonstrator helicopter is simulated to investigate dynamic stall using a loose computational fluid dynamics/structural dynamics (CFD/CSD) coupling of the flow solver FLOWer and the rotorcraft comprehensive code CAMRAD II. The rotor aerodynamics is computed using a high-fidelity delayed detached-eddy simulation (DDES). A three-degree-of-freedom trim of an isolated rotor is performed, yielding main-rotor control angles that agree well with the flight-test measurements. The flow field in this flight condition is found to be highly unsteady and complex, featuring massively separated flow, blade–vortex interaction, multiple dynamic-stall events, and shock-induced separation. The computed pitch-link loads are compared to flight-test measurements. This shows that all CFD/CSD cases underpredict the amplitudes of the flight test and yield phase shifts. However, overall trends agree reasonably. Also, varying the computational setup reveals that the shear stress transport–DDES turbulence model performs better than Spalart–Allmaras–DDES, that the consideration of the rotor hub and fuselage improves the agreement with flight-test data, and that the elastic twist plays only a minor role in the dynamic-stall events.

Sign in / Sign up

Export Citation Format

Share Document