Entrance, Viscous Dissipation and Temperature Dependent Viscosity Effects in Microchannel Flows With Convective Boundary Conditions

2006 ◽  
Author(s):  
C. Nonino ◽  
S. Del Giudice ◽  
S. Savino
Keyword(s):  
Boundary Conditions ◽  
Viscous Dissipation ◽  
Circular Cross Section ◽  
Laminar Flows ◽  
Projection Algorithm ◽  
Convective Boundary Conditions ◽  
Temperature Dependent ◽  
Temperature Dependent Viscosity ◽  
Convective Boundary ◽  
Dependent Viscosity

The effects of viscous dissipation and temperature dependent viscosity in simultaneously developing laminar flows of liquids in straight microchannels of circular cross-section are studied with reference to convective boundary conditions. Viscosity is assumed to vary linearly with temperature, in order to allow a parametric investigation, while the other fluid properties are held constant. A finite element procedure, based on a projection algorithm, is employed for the step-by-step solution of the parabolized momentum and energy equations. Axial distributions of the local overall Nusselt number and of the apparent Fanning friction factor are presented with reference to both heating and cooling conditions for three different values of the Biot number. Examples of temperature profiles at different axial locations are also shown.

Temperature-Dependent Viscosity and Viscous Dissipation Effects in Simultaneously Developing Flows in Microchannels With Convective Boundary Conditions

2006 ◽  
Vol 129 (9) ◽  
pp. 1187-1194 ◽  
Author(s):  
C. Nonino ◽  
S. Del Giudice ◽  
S. Savino
Keyword(s):  
Boundary Conditions ◽  
Viscous Dissipation ◽  
Laminar Flows ◽  
Projection Algorithm ◽  
Convective Boundary Conditions ◽  
Temperature Dependent ◽  
Temperature Dependent Viscosity ◽  
Convective Boundary ◽  
Radial Temperature ◽  
Dependent Viscosity

The effects of viscous dissipation and temperature dependent viscosity in simultaneously developing laminar flows of liquids in straight microchannels are studied with reference to convective boundary conditions. Two different geometries, namely the circular tube and the parallel plate channel, are considered. Viscosity is assumed to vary with temperature according to an exponential relation, while the other fluid properties are held constant. A finite element procedure, based on a projection algorithm, is employed for the step-by-step solution of the parabolized momentum and energy equations. Axial distributions of the local overall Nusselt number and of the apparent Fanning friction factor are presented with reference to both heating and cooling conditions for two different values of the Biot number. Examples of radial temperature profiles at different axial locations and of axial distributions of centerline velocity and temperature are also shown.

Effects of Temperature-Dependent Viscosity Variations and Boundary Conditions on Fully Developed Laminar Forced Convection in a Semicircular Duct

1998 ◽  
Vol 120 (3) ◽  
pp. 600-605 ◽  
Author(s):  
T. M. Harms ◽  
M. A. Jog ◽  
R. M. Manglik
Keyword(s):  
Boundary Conditions ◽  
Power Law ◽  
Numerical Solutions ◽  
Strong Dependence ◽  
Laminar Flows ◽  
Temperature Fields ◽  
Traditional Values ◽  
Temperature Dependent ◽  
Temperature Dependent Viscosity ◽  
Dependent Viscosity

Fully developed laminar flows in a semicircular duct with temperature-dependent viscosity variations in the flow cross section are analyzed, where the viscosity-temperature behavior is described by the Arrhenius model. Both the T and H1 boundary conditions are considered, as they represent the most fundamental heating/cooling conditions encountered in practical compact heat exchanger applications. Numerical solutions for the flow velocity and the temperature fields have been obtained by finite difference technique. The friction factor and Nusselt number results display a strong dependence on the viscosity ratio (μw/μb), and this is correlated using the classical power-law relationship. However, results indicate that the power-law exponents are significantly different from traditional values for circular tube. They are found to be functions of the flow geometry, boundary condition, and direction of heat transfer (heating or cooling).

Entrance, Viscous Dissipation and Temperature Dependent Viscosity Effects on the Laminar Forced Convection in Straight Microchannels With Uniform Wall Heat Flux

2008 ◽  
Author(s):  
C. Nonino ◽  
S. Savino ◽  
S. Del Giudice
Keyword(s):  
Heat Flux ◽  
Forced Convection ◽  
Viscous Dissipation ◽  
Laminar Flows ◽  
Uniform Heat Flux ◽  
Temperature Dependent ◽  
Temperature Dependent Viscosity ◽  
Wide Range ◽  
Dependent Viscosity ◽  
Laminar Forced Convection

A parametric investigation is carried out on the effects of viscous dissipation and temperature dependent viscosity in simultaneously developing laminar flows of liquids in straight microchannels of constant cross-sections. Reference is made to fluid heating conditions with a uniform heat flux imposed on the walls of the microchannels. Three different cross-sectional geometries are considered, chosen among those usually adopted for microchannels (rectangular, trapezoidal and hexagonal). Viscosity is assumed to vary with temperature according to an exponential relation, while the other fluid properties are held constant. A finite element procedure is employed for the solution of the parabolized momentum and energy equations. Due to the high value of the ratio between the total length and the hydraulic diameter in microchannels, such an approach is very advantageous with respect to the one based on the steady-state solution of the elliptic form of the governing equations in a three-dimensional domain corresponding to the whole duct. Computed axial distributions of the local Nusselt number and of the apparent Fanning friction factor are presented. Numerical results confirm that, in the laminar forced convection in the entrance region of straight microchannels, the effects of viscous dissipation and temperature dependent viscosity cannot be neglected in a wide range of operative conditions.

Analysis of the Effects of Joule Heating and Viscous Dissipation on Combined Pressure-Driven and Electrokinetic Flows in a Two-Parallel Plate Channel with Unequal Constant Temperatures

2018 ◽  
Vol 233 (4) ◽  
pp. 871-879 ◽  
Author(s):  
Harshad Sanjay Gaikwad ◽  
Pranab Kumar Mondal ◽  
Dipankar Narayan Basu ◽  
Nares Chimres ◽  
Somchai Wongwises
Keyword(s):  
Viscous Dissipation ◽  
Entropy Generation ◽  
Joule Heating ◽  
Generation Rate ◽  
Entropy Generation Rate ◽  
Local Entropy ◽  
Temperature Dependent ◽  
Temperature Dependent Viscosity ◽  
Dependent Viscosity ◽  
Local Entropy Generation

In this article, we perform an entropy generation analysis for the micro channel heat sink applications where the flow of fluid is actuated by combined influences of applied pressure gradient and electric field under electrical double layer phenomenon. The upper and lower walls of the channels are kept at different constant temperatures. The temperature-dependent viscosity of the fluid is considered and hence the momentum equation and energy equations are coupled in this study. Also, a hydrodynamic slip condition is employed on the viscous dissipation. For complete analysis of the entropy generation, we use a perturbation approach with lubrication approximation. In this study, we discuss the results depicting variations in the velocity and temperature distributions and their effect on local entropy generation rate and Bejan number in the system. It can be summarized from this analysis that the enhanced velocity gradients in the flow field due to combined effect of temperature-dependent viscosity and Joule heating and viscous dissipative effects, leads to an enhancement in the local entropy generation rate in the system.

A numerical study of solidification and viscous dissipation effects on polymer melt flow in plane channels

2013 ◽  
Vol 33 (2) ◽  
pp. 95-110
Author(s):  
Mustafa Tutar ◽  
Ali Karakus
Keyword(s):  
Shear Rate ◽  
Phase Change ◽  
Viscous Dissipation ◽  
Polymer Melt ◽  
Viscous Heating ◽  
Transient Phase ◽  
Melt Flow ◽  
Temperature Dependent ◽  
Temperature Dependent Viscosity ◽  
Dependent Viscosity

Abstract The combined effects of solidification and viscous dissipation on the hydrodynamic and thermal behavior of polymer melt flow during the injection process in a straight plane channel of constant cross section are numerically studied by considering the shear-rate and temperature-dependent viscosity and transient-phase change behavior. A numerical finite volume method, in conjunction with a modified form of the Cross constitutive equation to account for shear rate, temperature-dependent viscosity changes and a slightly modified form of the method proposed by Voller and Prakash to account for solidification of the liquid phase, is used and a validation with an analytical solution is presented for viscous heating effects. The hydrodynamic and solidified layers growth under the influence of a transient phase-change process and viscous dissipation, are analyzed for a commercial polymer melt flow, polypropylene (PP) for different parametric conditions namely, inflow velocity, polymer injection (inflow) temperature, the channel wall temperature, and the channel height. The results demonstrate that the proposed numerical formulations, including conjugate effects of viscous heating and transient-solidification on the present thermal transport process, can provide an accurate and realistic representation of polymer melt flow behavior during the injection molding process in plane channels with less simplifying assumptions.

Sign in / Sign up

Export Citation Format

Share Document