Pressure Drop Characteristics of Flow Boiling in Narrow Rectangular Channel

2013 ◽  
Author(s):  
Shu-ping Lv ◽  
Liang-ming Pan ◽  
De-qi Chen
Keyword(s):  
Pressure Drop ◽  
Two Phase Flow ◽  
Flow Boiling ◽  
Rectangular Channel ◽  
Working Fluid ◽  
Phase Flow ◽  
Two Phase ◽  
Experimental Conditions ◽  
Subcooled Flow Boiling ◽  
Flow Pressure

Pressure drop is the earliest and the most extensive issue in the research of two phase flow. Due to the influence of various factors on two phase flow pressure drop, there is no accurate and general correlation on this issue yet. In this paper, pressure drop characteristics of flow boiling were studied in a single vertical narrow rectangular channel with cross-section of 47 mm by 1.8 mm using water as working fluid. Subcooled flow boiling was experimentally investigated. The experimental conditions included inlet subcooling (2°C∼18°C), mass flow rate (222.3∼457.4 kg.m2s−1) and heat flux (113.6∼270.5 kW/m2). The influence of these parameters on the characteristics of flow boiling pressure drop has been investigated. The experimental results show that the conventional correlations failed to predict the two-phase flow pressure drop in this narrow rectangular channel. According to experiment results, a modified Chisholm correlation was proposed, and the new correlation gave more accurate predictions of the pressure drop.

INVESTIGATION ON VOID FRACTION FOR TWO-PHASE FLOW PRESSURE DROP OF EVAPORATIVE R-290 IN HORIZONTAL TUBE

2016 ◽  
Vol 78 (8-4) ◽  
Author(s):  
Agus Sunjarianto Pamitran ◽  
Sentot Novianto ◽  
Normah Mohd-Ghazali ◽  
Nasruddin Nasruddin ◽  
Raldi Koestoer
Keyword(s):  
Pressure Drop ◽  
Void Fraction ◽  
Two Phase Flow ◽  
Flow Boiling ◽  
Homogeneous Model ◽  
Saturation Temperature ◽  
Horizontal Tube ◽  
Phase Flow ◽  
Two Phase ◽  
Experimental Conditions

Two-phase flow boiling pressure drop experiment was conducted to observe its characteristics and to develop a new correlation of void fraction based on the separated model. Investigation is completed on the natural refrigerant R-290 (propane) in a horizontal circular tube with a 7.6 mm inner diameter under experimental conditions of 3.7 to 9.6 °C saturation temperature, 10 to 25 kW/m2 heat flux, and 185 to 445 kg/m2s mass flux. The present experimental data was used to obtain the calculated void fraction which then was compared to the predicted void fraction with 31 existing correlations. A new void fraction correlation for predicting two-phase flow boiling pressure drop, as a function of Reynolds numbers, was proposed. The measured pressure drop was compared to the predicted pressure drop with some existing pressure drop models that use the newly developed void fraction model. The homogeneous model of void fraction showed the best prediction with 2% deviation

scholarly journals Experimental Investigation and Prediction on Pressure Drop during Flow Boiling in Horizontal Microchannels

Micromachines ◽  
2021 ◽  
Vol 12 (5) ◽  
pp. 510
Author(s):  
Yan Huang ◽  
Bifen Shu ◽  
Shengnan Zhou ◽  
Qi Shi
Keyword(s):  
Pressure Drop ◽  
Flow Model ◽  
Two Phase Flow ◽  
Flow Boiling ◽  
Separated Flow ◽  
Heat Fluxes ◽  
Phase Flow ◽  
Vapor Quality ◽  
Two Phase ◽  
Gas Flux

In this paper, two-phase pressure drop data were obtained for boiling in horizontal rectangular microchannels with a hydraulic diameter of 0.55 mm for R-134a over mass velocities from 790 to 1122, heat fluxes from 0 to 31.08 kW/m2 and vapor qualities from 0 to 0.25. The experimental results show that the Chisholm parameter in the separated flow model relies heavily on the vapor quality, especially in the low vapor quality region (from 0 to 0.1), where the two-phase flow pattern is mainly bubbly and slug flow. Then, the measured pressure drop data are compared with those from six separated flow models. Based on the comparison result, the superficial gas flux is introduced in this paper to consider the comprehensive influence of mass velocity and vapor quality on two-phase flow pressure drop, and a new equation for the Chisholm parameter in the separated flow model is proposed as a function of the superficial gas flux . The mean absolute error (MAE ) of the new flow correlation is 16.82%, which is significantly lower than the other correlations. Moreover, the applicability of the new expression has been verified by the experimental data in other literatures.

Evaluation Analysis of Prediction Methods for Two-Phase Flow Pressure Drop in Mini-Channels

2008 ◽  
Author(s):  
Licheng Sun ◽  
Kaichiro Mishima
Keyword(s):  
Pressure Drop ◽  
Two Phase Flow ◽  
Phase Flow ◽  
Two Phase ◽  
Turbulent Region ◽  
Frictional Pressure Drop ◽  
New Correlation ◽  
Mini Channels ◽  
Flow Pressure ◽  
Better Than

2092 data of two-phase flow pressure drop were collected from 18 published papers of which the working fluids include R123, R134a, R22, R236ea, R245fa, R404a, R407C, R410a, R507, CO2, water and air. The hydraulic diameter ranges from 0.506 to 12mm; Relo from 10 to 37000, and Rego from 3 to 4×105. 11 correlations and models for calculating the two-phase frictional pressure drop were evaluated based upon these data. The results show that the accuracy of the Lockhart-Martinelli method, Mishima and Hibiki correlation, Zhang and Mishima correlation and Lee and Mudawar correalion in the laminar region is very close to each other, while the Muller-Steinhagen and Heck correlation is the best among the evaluated correlations in the turbulent region. A modified Chisholm correlation was proposed, which is better than all of the evaluated correlations in the turbulent region and its mean relative error is about 29%. For refrigerants only, the new correlation and Muller-Steinhagen and Heck correlation are very close to each other and give better agreement than the other evaluated correlations.

Sign in / Sign up

Export Citation Format

Share Document