scholarly journals Determination of Pool Boiling Critical Heat Flux Enhancement in Nanofluids

2007 ◽  
Author(s):  
Bao H. Truong
Keyword(s):  
Heat Flux ◽  
Critical Heat Flux ◽  
Pool Boiling ◽  
Nucleate Boiling ◽  
Porous Coating ◽  
Transfer Coefficients ◽  
Two Phase ◽  
Sem Images ◽  
Heat Transfer Coefficients ◽  
Nucleate Boiling Heat Transfer

Nanofluids are engineered colloids composed of nano-size particles dispersed in common fluids such as water or refrigerants. Using an electrically controlled wire heater, pool boiling Critical Heat Flux (CHF) of Alumina and Silica water-based nanofluids of concentration less than or equal to 0.1 percent by volume were measured. Silica nanofluids showed a CHF enhancement up to 68% and there seems to be a monotonic relationship between the nanoparticle concentration and the magnitude of enhancement. Alumina nanofluids had a CHF enhancement up to 56% but the peak occurred at the intermediate concentration. The boiling curves in nanofluid were found to shift to the left of that of water and correspond to higher nucleate boiling heat transfer coefficients in the two-phase flow regime. Scanning Electron Microscopy (SEM) images show a porous coating layer of nanoparticles on wires subjected to nanofluid CHF tests. These coating layers change the morphology of the heater’s surface, and are responsible for the CHF enhancement. The thickness of the coating was estimated using SEM and was found ranging from 3.0 to 6.0 micrometers for Alumina, and 3.0 to 15.0 micrometers for Silica.

Boiling Heat Transfer and Critical Heat Flux Enhancement of Upward- and Downward-Facing Heater in Nanofluids

2013 ◽  
Vol 135 (7) ◽  
Author(s):  
Muhamad Zuhairi Sulaiman ◽  
Masahiro Takamura ◽  
Kazuki Nakahashi ◽  
Tomio Okawa
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Critical Heat Flux ◽  
Boiling Heat Transfer ◽  
Pool Boiling ◽  
Nucleate Boiling ◽  
Flux Enhancement ◽  
Optimum Configuration ◽  
Wall Superheat ◽  
Nucleate Boiling Heat Transfer

Boiling heat transfer (BHT) and critical heat flux (CHF) performance were experimentally studied for saturated pool boiling of water-based nanofluids. In present experimental works, copper heaters of 20 mm diameter with titanium-oxide (TiO2) nanocoated surface were produced in pool boiling of nanofluid. Experiments were performed in both upward and downward facing nanofluid coated heater surface. TiO2 nanoparticle was used with concentration ranging from 0.004 until 0.4 kg/m3 and boiling time of tb = 1, 3, 10, 20, 40, and 60 mins. Distilled water was used to observed BHT and CHF performance of different nanofluids boiling time and concentration configurations. Nucleate boiling heat transfer observed to deteriorate in upward facing heater, however; in contrast effect of enhancement for downward. Maximum enhancements of CHF for upward- and downward-facing heater are 2.1 and 1.9 times, respectively. Reduction of mean contact angle demonstrate enhancement on the critical heat flux for both upward-facing and downward-facing heater configuration. However, nucleate boiling heat transfer shows inconsistency in similar concentration with sequence of boiling time. For both downward- and upward-facing nanocoated heater's BHT and CHF, the optimum configuration denotes by C = 400 kg/m3 with tb = 1 min which shows the best increment of boiling curve trend with lowest wall superheat ΔT = 25 K and critical heat flux enhancement of 2.02 times.

Forced Convective Boiling of Refrigerant HCFC123 in a Mini-Tube

2010 ◽  
Author(s):  
Koichi Araga ◽  
Keisuke Okamoto ◽  
Keiji Murata
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Mass Flux ◽  
Pool Boiling ◽  
Constant Heat Flux ◽  
Transfer Coefficients ◽  
Two Phase ◽  
Convective Boiling ◽  
Frictional Pressure Drop ◽  
Heat Transfer Coefficients

This paper presents an experimental investigation of the forced convective boiling of refrigerant HCFC123 in a mini-tube. The inner diameters of the test tubes, D, were 0.51 mm and 0.30 mm. First, two-phase frictional pressure drops were measured under adiabatic conditions and compared with the correlations for conventional tubes. The frictional pressure drop data were lower than the correlation for conventional tubes. However, the data were qualitatively in accord with those for conventional tubes and were correlated in the form φL2−1/Xtt. Next, heat transfer coefficients were measured under the conditions of constant heat flux and compared with those for conventional tubes and for pool boiling. The heat transfer characteristics for mini-tubes were different from those for conventional tubes and quite complicated. The heat transfer coefficients for D = 0.51 mm increased with heat flux but were almost independent of mass flux. Although the heat transfer coefficients were higher than those for a conventional tube with D = 10.3 mm and for pool boiling in the low quality region, they decreased gradually with increasing quality. The heat transfer coefficients for D = 0.30 mm were higher than those for D = 0.51 mm and were almost independent of both mass flux and heat flux.

scholarly journals Pool Boiling Performance of Multilayer Micromeshes for Commercial High-Power Cooling

Micromachines ◽  
2021 ◽  
Vol 12 (8) ◽  
pp. 980
Author(s):  
Kairui Tang ◽  
Jingjing Bai ◽  
Siyu Chen ◽  
Shiwei Zhang ◽  
Jie Li ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Critical Heat Flux ◽  
High Power ◽  
Rapid Development ◽  
Nucleate Boiling ◽  
Electronic Cooling ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Commercial Applications

With the rapid development of electronics, thermal management has become one of the most crucial issues. Intense research has focused on surface modifications used to enhance heat transfer. In this study, multilayer copper micromeshes (MCMs) are developed for commercial compact electronic cooling. Boiling heat transfer performance, including critical heat flux (CHF), heat transfer coefficients (HTCs), and the onset of nucleate boiling (ONB), are investigated. The effect of micromesh layers on the boiling performance is studied, and the bubbling characteristics are analyzed. In the study, MCM-5 shows the highest critical heat flux (CHF) of 207.5 W/cm2 and an HTC of 16.5 W(cm2·K) because of its abundant micropores serving as nucleate sites, and outstanding capillary wicking capability. In addition, MCMs are compared with other surface structures in the literature and perform with high competitiveness and potential in commercial applications for high-power cooling.

Nucleate Boiling and Critical Heat Flux From Protruded Chip Arrays During Flow Boiling

1993 ◽  
Vol 115 (1) ◽  
pp. 78-88 ◽  
Author(s):  
C. O. Gersey ◽  
I. Mudawar
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Critical Heat Flux ◽  
Single Phase ◽  
Liquid Velocity ◽  
Flow Boiling ◽  
Nucleate Boiling ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Subcooled Flow

The effects of chip protrusion on the forced-convection boiling and critical heat flux (CHF) of a dielectric coolant (FC-72) were investigated. The multi-chip module used in the present study featured a linear array of nine, 10 mm x 10 mm, simulated microelectronic chips which protruded 1 mm into a 20-mm wide side of a rectangular flow channel. Experiments were performed in vertical up flow with 5-mm and 2-mm channel gap thicknesses. For each configuration, the velocity and subcooling of the liquid were varied from 13 to 400 cm/s and 3 to 36° C, respectively. The nucleate boiling regime was not affected by changes in velocity and subcooling, and critical heat flux generally increased with increases in either velocity or subcooling. Higher single-phase heat transfer coefficients and higher CHF values were measured for the protruded chips compared to similar flush-mounted chips. However, adjusting the data for the increased surface area and the increased liquid velocity above the chip caused by the protruding chips yielded a closer agreement between the protruded and flush-mounted results. Even with the velocity and area adjustments, the most upstream protruded chip had higher single-phase heat transfer coefficients and CHF values for high velocity and/or highly-subcooled flow as compared the downstream protruded chips. The results show that, except for the most upstream chip, the performances of protruded chips are very similar to those of flush-mounted chips.

Pool Boiling of Benzene, Diphenyl, and Benzene-Diphenyl Mixtures Under Pressure

1963 ◽  
Vol 85 (3) ◽  
pp. 215-220 ◽  
Author(s):  
D. A. Huber ◽  
J. C. Hoehne
Keyword(s):  
Heat Flux ◽  
Critical Heat Flux ◽  
Pool Boiling ◽  
Physical Property ◽  
Horizontal Tube ◽  
Nucleate Boiling ◽  
Volatile Components ◽  
Pure Fluids ◽  
Nucleate Boiling Heat Transfer ◽  
Physical Property Data

Experimental measurements are presented for the nucleate boiling of benzene, diphenyl, and benzene-diphenyl mixtures on a 3/8-in. od horizontal tube. The data were obtained in a pool boiling apparatus at pressures ranging from 13.5 to 488.5 psia. For the pure fluids, the nucleate boiling heat-transfer data were best correlated by the Rohsenow [12], Gilmour [8], and Levy [10] equations. Critical heat flux data reported for these fluids are correlated with those in the literature. The critical heat flux values for the pure fluids were best correlated by the Bernath relationship [1]; however, none of the literature expressions adequately predicted the large increases in critical heat flux that were obtained when small percentages of benzene were added to diphenyl. Similar increases in critical heat flux, when small amounts of volatile components are added, have been noted before, but no generalized correlations have been advanced. Some of the discrepancy may be due to inadequate knowledge of physical property data for the mixtures and failure to account for the mass transfer which occurs in bubble growth of multicomponent mixtures.

Boiling Heat Transfer and Critical Heat Flux Enhancement of Upward- and Downward-Facing Heater in Nanofluids

2012 ◽  
Author(s):  
Muhamad Zuhairi Sulaiman ◽  
Masahiro Takamura ◽  
Kazuki Nakahashi ◽  
Tomio Okawa
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Critical Heat Flux ◽  
Boiling Heat Transfer ◽  
Pool Boiling ◽  
Nucleate Boiling ◽  
Flux Enhancement ◽  
Optimum Configuration ◽  
Wall Superheat ◽  
Nucleate Boiling Heat Transfer

Boiling heat transfer (BHT) and critical heat flux (CHF) performance were experimentally studied for saturated pool boiling of water-based nanofluids. In present experimental works, copper heaters of 20 mm diameter with titanium-oxide (TiO2) nanocoated surface were produced in pool boiling of nanofluid. Experiments were performed in both upward and downward facing nanofluid coated heater surface. TiO2 nanoparticle was used with concentration ranging from 0.004 until 0.4 kg/m3 and boiling time of tb = 1, 3, 10, 20, 40 and 60 minutes. Distilled water was used to observed BHT and CHF performance of different nanofluids boiling time and concentration configurations. Nucleate boiling heat transfer observed to deteriorate in upward facing heater, however, in contrast effect of enhancement for downward. Maximum CHF for upward- and downward-facing heater are 2.1 and 1.9, respectively. Reduction of mean contact angle demonstrate enhancement on the critical heat flux for both upward-facing and downward-facing heater configuration. However, nucleate boiling heat transfer shows inconsistency in similar concentration with sequence of boiling time. For both downward- and upward-facing nanocoated heater’s BHT and CHF, the optimum configuration denotes by C = 400 kg/m3 with tb = 1 minute which shows the best increment of boiling curve trend with lowest wall superheat ΔT = 25 K and critical heat flux enhancement of 2.02 times.

Nucleate boiling heat transfer coefficients of halogenated refrigerants up to critical heat fluxes

2009 ◽  
Vol 223 (6) ◽  
pp. 1415-1424 ◽  
Author(s):  
K-J Park ◽  
D Jung ◽  
S E Shim
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Boiling Heat Transfer ◽  
Pool Boiling ◽  
Nucleate Boiling ◽  
Heat Fluxes ◽  
Nucleate Pool Boiling ◽  
Transfer Coefficients ◽  
Average Deviation ◽  
Heat Transfer Coefficients

In this work, nucleate pool boiling heat transfer coefficients (HTCs) of five refrigerants of differing vapour pressures are measured on a horizontal, smooth copper surface of 9.53×9.53 mm. The tested refrigerants are R123, R152a, R134a, R22, and R32 and HTCs are taken from 10 kW/m2 to the critical heat flux (CHF) of each refrigerant. Wall and fluid temperatures are measured directly by thermocouples located underneath the test surface and in the liquid pool, respectively. Test results show that nucleate pool boiling HTCs of halogenated refrigerants increase as the heat flux and vapour pressure increase. This typical trend is maintained even at high heat fluxes above 200 kW/m2. Zuber's prediction equation for CHF is quite accurate showing a maximum deviation of 21 per cent for all refrigerants tested. For all refrigerants, Stephan and Abdelsalam's well-known correlation underpredicted nucleate boiling HTC data up to the CHF with an average deviation of 21.3 per cent, while Cooper's correlation overpredicted the data with an average deviation of 14.2 per cent. On the other hand, Gorenflo's and Jung et al.'s correlations showed 5.8 and 6.4 per cent deviations, respectively, in the entire nucleate boiling range up to the CHF.

Sign in / Sign up

Export Citation Format

Share Document