High Heat Flux Subcooled Flow Boiling of Methanol in Microtubes

2015 ◽  
Author(s):  
Farzad Houshmand ◽  
Hyoungsoon Lee ◽  
Mehdi Asheghi ◽  
Kenneth E. Goodson
Keyword(s):  
Heat Flux ◽  
Pressure Drop ◽  
Flow Boiling ◽  
High Heat ◽  
Heat Fluxes ◽  
Two Phase ◽  
Subcooled Flow Boiling ◽  
Subcooled Flow ◽  
Inner Diameter ◽  
Phase Pressure

As the proper cooling of the electronic devices leads to significant increase in the performance, two-phase heat transfer to dielectric liquids can be of an interest especially for thermal management solutions for high power density devices with extremely high heat fluxes. In this paper, the pressure drop and critical heat flux (CHF) for subcooled flow boiling of methanol at high heat fluxes exceeding 1 kW/cm2 is investigated. Methanol was propelled into microtubes (ID = 265 and 150 μm) at flow rates up to 40 ml/min (mass fluxes approaching 10000 kg/m2-s), boiled in a portion of the microtube by passing DC current through the walls, and the two-phase pressure drop and CHF were measured for a range of operating parameters. The two-phase pressure drop for subcooled flow boiling was found to be significantly lower than the saturated flow boiling case, which can lead to lower pumping powers and more stability in the cooling systems. CHF was found to be increasing almost linearly with Re and inverse of inner diameter (1/ID), while for a given inner diameter, it decreases with increasing heated length.

Analysis of Two-Phase Pressure Drop Fluctuation Characteristics in a Single Mini-Channel

2016 ◽  
Vol 366 ◽  
pp. 151-156
Author(s):  
Bei Chen Zhang ◽  
Qing Lian Li ◽  
Yuan Wang ◽  
Jian Qiang Zhang
Keyword(s):  
Heat Flux ◽  
Pressure Drop ◽  
Mass Flux ◽  
Flow Boiling ◽  
Circular Cross Section ◽  
Low Frequency ◽  
Amplitude Fluctuation ◽  
Heat Fluxes ◽  
Two Phase ◽  
Phase Pressure

Two-phase pressure drop fluctuations during flow boiling in a single mini-channel were experimentally investigated. Degassed water was tested in circular cross section mini-channels with the hydraulic diameter of 1.0 mm at liquid mass fluxes range of 21.19-84.77 kg m-2 s-1 and heat fluxes of 0~155.75 kW m-2. Effects of heat flux and mass flux on pressure drop fluctuations were discussed based on the time and frequency domain analysis of the measured pressure drop. Two types of fluctuations were identified, which are the incipient boiling fluctuation (IBF) and the explosive boiling fluctuation (EBF) respectively. The IBF is a low frequency low amplitude fluctuation, which relates to the bubble dynamics when incipient boiling occurs. It is sensitive to the thermal and flow conditions. With the increase of heat flux and mass flux, the IBF is suppressed. The EBF is a low frequency high amplitude fluctuation, which occurs near the critical heat flux.

On the Operational Parameters Effects on Two-Phase Pressure Drop Characteristics of Reentrant Copper Microchannels

2016 ◽  
Author(s):  
Daxiang Deng ◽  
Qingsong Huang ◽  
Yanlin Xie ◽  
Wei Zhou ◽  
Xiang Huang ◽  
...  
Keyword(s):  
Heat Flux ◽  
Pressure Drop ◽  
Mass Flux ◽  
Heat Sink ◽  
Flow Boiling ◽  
Heat Fluxes ◽  
High Heat Flux ◽  
Two Phase ◽  
Cooling Systems ◽  
Phase Pressure

Two-phase boiling in advanced microchannel heat sinks offers an efficient and attractive solution for heat dissipation of high-heat-flux devices. In this study, a type of reentrant copper microchannels was developed for heat sink cooling systems. It consisted of 14 parallel Ω-shaped reentrant copper microchannels with a hydraulic diameter of 781μm. Two-phase pressure drop characteristics were comprehensively accessed via flow boiling tests. Both deionized water and ethanol tests were conducted at inlet subcooling of 10°C and 40°C, mass fluxes of 125–300kg/m2·s, and a wide range of heat fluxes and vapor qualities. The effects of heat flux, mass flux, inlet subcoolings and coolants on the two-phase pressure drop were systematically explored. The results show that the two-phase pressure drop of reentrant copper microchannels generally increased with increasing heat fluxes and vapor qualities. The role of mass flux and inlet temperatures was dependent on the test coolant. The water tests presented smaller pressure drop than the ethanol ones. These results provide critical experimental information for the development of microchannel heat sink cooling systems, and are of considerable practical relevance.

A theoretical and experimental study on subcooled flow boiling at high heat flux

1994 ◽  
Vol 29 (5) ◽  
pp. 319-327 ◽  
Author(s):  
K. W. Lin ◽  
C. H. Lee ◽  
L. W. Hourng ◽  
J. C. Hsu
Keyword(s):  
Experimental Study ◽  
Heat Flux ◽  
Flow Boiling ◽  
High Heat ◽  
High Heat Flux ◽  
Subcooled Flow Boiling ◽  
Subcooled Flow

E219 High Heat Flux Cooling for Electronic Devices by Subcooled Flow Boiling : Cooing performance of small channel

2001 ◽  
Vol 2001 (0) ◽  
pp. 553-554
Author(s):  
Koichi SUZUKI ◽  
Hiroki SAITO ◽  
Hiroshi KAWAMURA ◽  
Hideo IWASAKI ◽  
Koichiro KAWANO ◽  
...  
Keyword(s):  
Heat Flux ◽  
Flow Boiling ◽  
Electronic Devices ◽  
High Heat ◽  
High Heat Flux ◽  
Subcooled Flow Boiling ◽  
Small Channel ◽  
Subcooled Flow

High heat flux burnout in subcooled flow boiling

1995 ◽  
Vol 4 (3) ◽  
pp. 151-161
Author(s):  
G. P. Celata ◽  
M. Cumo ◽  
A. Mariani
Keyword(s):  
Heat Flux ◽  
Flow Boiling ◽  
High Heat ◽  
High Heat Flux ◽  
Subcooled Flow Boiling ◽  
Subcooled Flow

Subcooled Flow Boiling With Microbubble Emission in a Michrochannel

2009 ◽  
Author(s):  
Koichi Suzuki ◽  
Tomoyuki Nomura ◽  
Chungpyo Hong ◽  
Kazuhisa Yuki
Keyword(s):  
Heat Flux ◽  
Liquid Velocity ◽  
Flow Boiling ◽  
Atmospheric Condition ◽  
High Heat ◽  
Hydraulic Diameter ◽  
Maximum Pressure ◽  
High Heat Flux ◽  
Subcooled Flow Boiling ◽  
Subcooled Flow

Subcooled flow boiling of water has been investigated for the horizontal multi-microchannel of which hydraulic diameter is 150μm for unit channel. Eleven rectangular microchannels are made on a top of copper heating block of 5.25mm × 5.25mm. The outlet of the channel is opened to the atmospheric surroundings and the maximum pressure in the channel is lower than 25mmHg. The boiling test is performed under the nearly atmospheric condition. The experimental results are discussed compared with subcooled boiling of water in a microchannel of 155μm in hydraulic diameter with Platinum film microheater of 2000μm in length and 200μm in width obtained by Ping Cheng and his co-workers. According to the authors’ previous experiments on subcooled flow boiling in mini and conventional channels, the critical heat flux decreases with decreasing of the hydraulic diameter of the channel. The boiling in the microchannel turns to film boiling after reaching CHF without microbubble emission boiling (MEB) regardless of liquid subcooling and liquid velocity even if the boiling condition is the same as MEB in the minichannels. In the high heat flux region, whole of the microchannels is completely covered with large coalescing bubbles. The results are much different from those of experiments with Platinum film microheater, which have 14.41 MW/m2 of heat flux in MEB. It is difficult to introduce liquid–vapor exchange including MEB for the large capacitance heat sink in microchannel boiling.

A Photographic study of subcooled flow boiling burnout at high heat flux and velocity

2007 ◽  
Vol 50 (1-2) ◽  
pp. 283-291 ◽  
Author(s):  
G.P. Celata ◽  
M. Cumo ◽  
D. Gallo ◽  
A. Mariani ◽  
G. Zummo
Keyword(s):  
Heat Flux ◽  
Flow Boiling ◽  
High Heat ◽  
High Heat Flux ◽  
Subcooled Flow Boiling ◽  
Subcooled Flow

scholarly journals Optimal design of subcooled triangular microchannel heat sink exchangers with variable heat loads for high performance cooling

2021 ◽  
Vol 2116 (1) ◽  
pp. 012052
Author(s):  
David Olugbenga Ariyo ◽  
Tunde Bello-Ochende
Keyword(s):  
Heat Sink ◽  
High Performance ◽  
Flow Boiling ◽  
High Heat ◽  
Geometric Optimization ◽  
Heat Fluxes ◽  
Heat Sinks ◽  
Subcooled Flow Boiling ◽  
Subcooled Flow ◽  
Microchannel Heat Sinks

Abstract Deionized water at a temperature of 25 °C was used as the cooling fluid and aluminium as the heat sink material in the geometric optimization and parameter modelling of subcooled flow boiling in horizontal equilateral triangular microchannel heat sinks. The thermal resistances of the microchannels were minimized subject to fixed volume constraints of the heat sinks and microchannels. A computational fluid dynamics (CFD) ANSYS code used for both the simulations and the optimizations was validated by the available experimental data in the literature and the agreement was good. Fixed heat fluxes between 100 and 500 W/cm2 and velocities between 0.1 and 7.0 m/s were used in the study. Despite the relatively high heat fluxes in this study, the base temperatures of the optimal microchannel heat sinks were within the acceptable operating range for modern electronics. The pumping power requirements for the optimal microchannels are low, indicating that they can be used in the cooling of electronic devices.

Single-Side Heated Monoblock, High Heat Flux Removal Using Water Subcooled Flow Boiling

2003 ◽  
Author(s):  
Ronald D. Boyd ◽  
Ali Ekhlassi ◽  
Penrose Cofie ◽  
Richard Martin ◽  
Hongtao Zhang
Keyword(s):  
Heat Flux ◽  
Wall Temperature ◽  
Test Section ◽  
Flow Boiling ◽  
Three Dimensional ◽  
High Heat ◽  
High Heat Flux ◽  
Subcooled Flow Boiling ◽  
Subcooled Flow ◽  
Single Side

Plasma-facing components for fusion reactors and other high heat flux heat sinks are usually subjected to a peripherally non-uniform heat flux. The configuration under study is related to these applications and consists of a single-side heated monoblock cross-section test section with a circular coolant channel bored through the center. The monoblock test section has a heated length of 180.0 mm and has 10.0 mm and 30.0 mm inside diameter and outside square sides, respectively. It was subjected to a constant heat flux on one side only, and the remaining portion of the outside surfaces is not exposed to a heat flux. The inlet channel water temperature was held near at 26.0°C, the exit pressure was maintained at 0.207 MPa, and the mass velocity was 0.59 Mg/m2s. The results consist of three-dimensional monoblock test section wall temperature distributions and a clear display of both critical heat flux and post-critical heat flux for this single-side heated configuration. These results are very encouraging in that they are among the first full set of truly three-dimensional monoblock test section wall temperature measurements for a one-side heated monoblock flow channel which contains the effects of conjugate heat transfer for turbulent, subcooled flow boiling. Comparisons are made between these results for the monoblock test section and those for a single-side heated circular test section.

Sign in / Sign up

Export Citation Format

Share Document