Application of Paper Mill Biosolids, Wood Ash and Ground Bark on Wild Lowbush Blueberry Production

2004 ◽  
pp. 13-20
Keyword(s):  
Paper Mill ◽  
Wood Ash ◽  
Lowbush Blueberry

Removal of colour from a kraft pulp and paper mill effluent in Kenya using a combination of electrochemical method and phosphate rock

2007 ◽  
Vol 55 (6) ◽  
pp. 15-22 ◽  
Author(s):  
L. Etiégni ◽  
O.D. Oricho ◽  
K. Ofosu-Asiedu ◽  
K.A. Senelwa ◽  
K.G. Surtan ◽  
...  
Keyword(s):  
Electrochemical Method ◽  
Phosphate Rock ◽  
Complete Removal ◽  
Paper Mill ◽  
Wood Ash ◽  
Electrochemical Process ◽  
Pulp And Paper Mill ◽  
Allowable Limit ◽  
Paper Mill Effluent ◽  
Treated Effluent

A study was undertaken to remove colour from a kraft mill's treated effluent in Kenya and determine the suitability of phosphate rock to replace wood ash during the electrochemical process. The electrochemical method alone, electrochemical combined with alum (ELCAL), wood ash leachate (ELCAS) and phosphate rock (ELPHOS) solutions at a rate of 165 to 1,000 g/m3 were tested. Effluent characteristics were determined after complete removal of colour. Same reduction rates of TS (85%) and TSS (89%) were recorded by ELCAS and ELPHOS. However, ELPHOS removed more COD (86 to 91%) and more BOD (85 to 92%) than ELCAS. Furthermore, the pH of ELPHOS treated solution was 9.3, within the Kenya Local Government's allowable limit. Power reduction with ELCAS and ELPHOS varied between 53 to 73% and 49 to 69% respectively but the difference was not statistically significant. Overnight aeration further improved the quality of ELCAS and ELPHOS treated effluent, reducing BOD and COD values to 0 mg/l. ELPHOS cost ($0.29/m3) was nevertheless three times higher than that of ELCAS ($0.10/m3), mainly because of free wood ash. ELPHOS did not also increase effluent phosphorus. It was therefore recommended that various ways be explored in making ELPHOS more economical to replace ELCAS.

Soil phosphorus fractions following annual paper mill biosolids and liming materials application

2010 ◽  
Vol 90 (3) ◽  
pp. 467-479 ◽  
Author(s):  
J -L. Fan ◽  
N. Ziadi ◽  
B. Gagnon ◽  
Z -Y. Hu
Keyword(s):  
Chemical Properties ◽  
Paper Mill ◽  
Wood Ash ◽  
P Availability ◽  
P Fractions ◽  
Soil P ◽  
Neutralization Capacity ◽  
Soil P Fractions ◽  
Lime Mud ◽  
By Products

Industrial by-products such as paper mill biosolids (PB) and different liming materials have been used as fertilizers and amendments in agricultural soils for many decades. However, little is known about the effects of their repeated application on soil nutrient availability, particularly phosphorus (P). A 6-yr field study (2000-2005) was conducted in the province of Quebec to investigate the effect of repeated annual applications of different PB and industrial by-products on selected soil chemical properties, especially soil P fractions. Different PB rates (0 to 90 Mg wet ha-1) and several liming products (lime mud, wood ash, calcitic lime, and Mg by-products) were annually applied to field crops after seeding. Soils were sampled before seeding in May 2003 and at harvest in October 2005. Results showed that HCl-P was the largest P pool, accounting for about 64% of the total P fraction, and that the repeated applications of liming products significantly increased this pool and decreased the organic P pools. The NaOH-Po and residual-P were significantly lower in 2005 than in 2003, indicating that PB application without supplemental P fertilizer inputs enhanced the mobility and/or mineralization of NaOH-Po and the transformation of recalcitrant P to more labile forms with time. Lime mud (LM) was found to be the best liming material owing to its high neutralization capacity and positive effect on soil P availability over time. Key words: Paper mill biosolids, alkaline residuals, lime, wood ash, soil P fractions

Electro-coagulation treatment efficiency of graphite, iron and aluminum electrodes using alum and wood ash electrolytes on a Kraft pulp and paper mill effluent

2010 ◽  
Vol 62 (7) ◽  
pp. 1526-1535 ◽  
Author(s):  
O. B. Orori ◽  
L. Etiégni ◽  
K. Senelwa ◽  
M. M. Mwamburi ◽  
K. B. Balozi ◽  
...  
Keyword(s):  
Power Consumption ◽  
Kraft Pulp ◽  
Paper Mill ◽  
Wood Ash ◽  
Pulp And Paper ◽  
Effluent Treatment ◽  
Specific Power ◽  
Pulp And Paper Mill ◽  
Treatment Efficiency ◽  
Sampling Points

Specific power consumption and reduction of BOD, COD, TS, pH, and chemical elements were used to determine the treatment efficiency of Fe, graphite and Al electrodes with alum and wood ash as supporting electrolytes on the effluent from a Kraft pulp and paper mill in Kenya. Five sampling points were selected along mill's effluent treatment system: primary settling tank (SP1), first aerated lagoon (SP2), second aerated lagoon (SP3), stabilization pond (SP4), and at discharge point (SP5). Operating costs were also compared between treatments. Graphite electrodes combined with alum showed the lowest power consumption (0.5 to 3.9 mWh/m3), followed by Al and Fe. All the electrodes reduced color from a maximum of 3,200°H to the minimum local standard of 15°H. However Al electrode with alum was the most effective method for BOD and COD reduction by over 60% and 58.8% respectively and generated less sludge at all sampling points. The cost of treatment was lowest with graphite electrode (US$0.006 to 0.0008 per m3 of effluent), but highest with Al electrodes combined with wood ash (US$31.74 to 8.34 per m3). Further study is required for the effectiveness of increasing the concentration of wood ash leachate at higher concentration and current density.

Chemical, anatomical, and technology aspects of Eucalyptus benthamii and Eucalyptus dunii for use in an integrated pulp and paper mill

TAPPI Journal ◽  
2015 ◽  
Vol 14 (2) ◽  
pp. 73-81 ◽  
Author(s):  
GISELY SAMISTRARO ◽  
PETER W. HART ◽  
JORGE LUIZ COLODETTE ◽  
RICARDO PAIM
Keyword(s):  
Energy Levels ◽  
Black Liquor ◽  
Basic Density ◽  
Paper Mill ◽  
Frost Tolerance ◽  
Strength Properties ◽  
Kappa Number ◽  
Pulp Yield ◽  
Chemical Compositions ◽  
Physical Strength

Eucalyptus dunii has been commercially used in southern Brazil because of its relatively good frost tolerance and adequate productivity in the winter months. More recently, interest has grown in cultivating Eucalyptus benthamii Maiden & Cambage, which presents even superior frost tolerance compared to E. dunii and is highly productive as well. The quality of E. benthamii for pulp production is not yet proven. Thus, the chemical, anatomical, and technological aspects of pulp made from E. benthamii were compared with those of E. dunii for unbleached paper production. Samples of E. benthamii chips were obtained and analyzed for their basic density, chemical composition, higher heating value, trace elemental analysis, and chip size distribution. The chips were kraft cooked using conditions that produced a 74 ± 6 kappa number. The pulps were characterized for kappa number, yield, viscosity, and morphologic characteristics (e.g., length, wall thickness, and coarseness). Black liquor was analyzed for total solids, organics, inorganics, sodium sulfide, sodium hydroxide, and sodium carbonate. Brownstocks were beaten at five different energy levels in a Valley beater, and the physical strength properties of 120 g/m² handsheets were measured to develop a beater curve. The results of this study showed differences in delignification between the two woods and lower pulp yield for E. benthamii , which are related to their chemical compositions and basic densities. The E. benthamii studied in this work exhibited higher amounts of lignin and extractives, lower carbohydrate content, and lower basic density. However, cooking a blend of the two woods afforded good results in pulping and in physical pulp properties.

Application of a Pilot-Scale Pulsed Electrocoagulation system to OCC-Based Paper Mill Effluent

TAPPI Journal ◽  
2009 ◽  
Vol 8 (3) ◽  
pp. 14-20 ◽  
Author(s):  
YUAN-SHING PERNG ◽  
EUGENE I-CHEN WANG ◽  
SHIH-TSUNG YU ◽  
AN-YI CHANG
Keyword(s):  
Water Quality ◽  
Quality Indicators ◽  
Paper Mill ◽  
Pilot Scale ◽  
Operating Conditions ◽  
Optimal Dosage ◽  
Water Quality Indicators ◽  
Paper Mill Effluent ◽  
Treated Effluent ◽  
True Color

Trends toward closure of white water recirculation loops in papermaking often lead to a need for system modifications. We conducted a pilot-scale study using pulsed electrocoagulation technology to treat the effluent of an old corrugated containerboard (OCC)-based paper mill in order to evaluate its treatment performance. The operating variables were a current density of 0–240 A/m2, a hydraulic retention time (HRT) of 8–16 min, and a coagulant (anionic polyacrylamide) dosage of 0–22 mg/L. Water quality indicators investigated were electrical con-ductivity, suspended solids (SS), chemical oxygen demand (COD), and true color. The results were encouraging. Under the operating conditions without coagulant addition, the highest removals for conductivity, SS, COD, and true color were 39.8%, 85.7%, 70.5%, and 97.1%, respectively (with an HRT of 16 min). The use of a coagulant enhanced the removal of both conductivity and COD. With an optimal dosage of 20 mg/L and a shortened HRT of 10 min, the highest removal achieved for the four water quality indicators were 37.7%, 88.7%, 74.2%, and 91.7%, respectively. The water qualities thus attained should be adequate to allow reuse of a substantial portion of the treated effluent as process water makeup in papermaking.

Sign in / Sign up

Export Citation Format

Share Document