Wind Turbine Performance Evaluation and CFD Technique

2004 ◽  
Vol 2004 (0) ◽  
pp. 169
Author(s):  
Hikaru Matsumiya ◽  
Tetsuya Kogaki
Keyword(s):  
Performance Evaluation ◽  
Wind Turbine ◽  
Turbine Performance

Site calibration for the wind turbine performance evaluation

2004 ◽  
Vol 18 (12) ◽  
pp. 2250-2257 ◽  
Author(s):  
Yoonsu Nam ◽  
Neungsoo Yoo ◽  
Jungwan Lee
Keyword(s):  
Performance Evaluation ◽  
Wind Turbine ◽  
Turbine Performance

scholarly journals Performance assessment and optimization of a helical Savonius wind turbine by modifying the Bach’s section

2021 ◽  
Vol 3 (8) ◽  
Author(s):  
M. Niyat Zadeh ◽  
M. Pourfallah ◽  
S. Safari Sabet ◽  
M. Gholinia ◽  
S. Mouloodi ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Performance Assessment ◽  
Turbulent Flows ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Tip Speed Ratio ◽  
Basic Model ◽  
Turbine Performance ◽  
Primary Model ◽  
Savonius Wind Turbine

AbstractIn this paper, we attempted to measure the effect of Bach’s section, which presents a high-power coefficient in the standard Savonius model, on the performance of the helical Savonius wind turbine, by observing the parameters affecting turbine performance. Assessment methods based on the tip speed ratio, torque variation, flow field characterizations, and the power coefficient are performed. The present issue was stimulated using the turbulence model SST (k- ω) at 6, 8, and 10 m/s wind flow velocities via COMSOL software. Numerical simulation was validated employing previous articles. Outputs demonstrate that Bach-primary and Bach-developed wind turbine models have less flow separation at the spoke-end than the simple helical Savonius model, ultimately improving wind turbines’ total performance and reducing spoke-dynamic loads. Compared with the basic model, the Bach-developed model shows an 18.3% performance improvement in the maximum power coefficient. Bach’s primary model also offers a 12.4% increase in power production than the initial model’s best performance. Furthermore, the results indicate that changing the geometric parameters of the Bach model at high velocities (in turbulent flows) does not significantly affect improving performance.

scholarly journals Design Oriented Aerodynamic Modelling of Wind Turbine Performance

2007 ◽  
Vol 75 ◽  
pp. 012011 ◽  
Author(s):  
Luca Greco ◽  
Claudio Testa ◽  
Francesco Salvatore
Keyword(s):  
Wind Turbine ◽  
Turbine Performance ◽  
Aerodynamic Modelling

Axial Turbine Performance Evaluation. Part B—Optimization With and Without Constraints

1968 ◽  
Vol 90 (4) ◽  
pp. 349-359 ◽  
Author(s):  
O. E. Balje´ ◽  
R. L. Binsley
Keyword(s):  
Reynolds Number ◽  
Performance Evaluation ◽  
Reference Value ◽  
Tip Clearance ◽  
Strong Function ◽  
Turbine Performance ◽  
Wide Range ◽  
Leakage Area ◽  
Partial Admission ◽  
Specific Speed

The maximum obtainable efficiency and associated geometry have been calculated based on the use of generalized loss correlations from Part A and are presented for full and partial admission turbines over a wide range of specific speeds. The calculated effects of varying values of Reynolds number, tip clearance, and trailing edge thickness on turbine performance are presented. Because of the anticipated difficulty in fabricating some of the optimum geometries calculated, the effects of using nonoptimum values of geometric parameters on attainable efficiency have also been investigated. The derating factor for machine Reynolds number is shown to be a strong function of specific speed, varying from 0.96 at a specific speed of 100, to 0.6 at a specific speed of 3, when Reynolds number is 105 compared to a reference value of 106. The derating factor for tip clearance is shown to be similar to what would be expected if the clearance area were considered as a leakage area. The use of blade heights, blade numbers, rotor exit angles, and degrees of reaction varying from the optimum by 25 percent produce maximum derating factors of 0.99, 0.98, 0.985, and 0.97, respectively, when compared to full optimum values.

Sign in / Sign up

Export Citation Format

Share Document