scholarly journals Performance assessment and optimization of a helical Savonius wind turbine by modifying the Bach’s section

2021 ◽  
Vol 3 (8) ◽  
Author(s):  
M. Niyat Zadeh ◽  
M. Pourfallah ◽  
S. Safari Sabet ◽  
M. Gholinia ◽  
S. Mouloodi ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Performance Assessment ◽  
Turbulent Flows ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Tip Speed Ratio ◽  
Basic Model ◽  
Turbine Performance ◽  
Primary Model ◽  
Savonius Wind Turbine

AbstractIn this paper, we attempted to measure the effect of Bach’s section, which presents a high-power coefficient in the standard Savonius model, on the performance of the helical Savonius wind turbine, by observing the parameters affecting turbine performance. Assessment methods based on the tip speed ratio, torque variation, flow field characterizations, and the power coefficient are performed. The present issue was stimulated using the turbulence model SST (k- ω) at 6, 8, and 10 m/s wind flow velocities via COMSOL software. Numerical simulation was validated employing previous articles. Outputs demonstrate that Bach-primary and Bach-developed wind turbine models have less flow separation at the spoke-end than the simple helical Savonius model, ultimately improving wind turbines’ total performance and reducing spoke-dynamic loads. Compared with the basic model, the Bach-developed model shows an 18.3% performance improvement in the maximum power coefficient. Bach’s primary model also offers a 12.4% increase in power production than the initial model’s best performance. Furthermore, the results indicate that changing the geometric parameters of the Bach model at high velocities (in turbulent flows) does not significantly affect improving performance.

scholarly journals Drag coefficient calculation of modified Myring-Savonius wind turbine with numerical simulations

2020 ◽  
Vol 10 (2) ◽  
pp. 73-84
Author(s):  
Mahmoud Saleh ◽  
Endre Kovács
Keyword(s):  
Drag Coefficient ◽  
Wind Turbine ◽  
Primary Objective ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Energy Potential ◽  
Cross Sectional ◽  
Ansys Fluent ◽  
Tip Speed Ratio ◽  
Savonius Wind Turbine

Nowadays the importance of renewable energy is growing, and the utilization of the low wind energy potential is getting crucial. There are turbines with low and high tip speed ratio. Turbines with low tip speed ratio such as the Savonius wind turbine can generate adequate amount of torque at low wind velocities. These types of turbines are also called drag machines. The geometry of the blade can greatly influence the efficiency of the device. With Computational Fluid Dynamics (CFD) method, several optimizations can be done before the production. In our paper the Savonius wind turbine blade geometry was designed based on the so-called Myring equation. The primary objective of this paper was to investigate the drag coefficient of the force acting on the surface of the blade. Also, the Karman vortex was investigated and the space ratio of that vortex in our simulation was compared to a typical one. The power coefficient of a new Savonius turbine was investigated at different values of top speed ratio (TSR). For the sake of simplicity, a 2D cross-sectional area was investigated in the simulation with ANSYS Fluent 19.2.

scholarly journals Numerical Model Analysis of Myring–Savonius wind turbines

2019 ◽  
Vol 4 (1) ◽  
pp. 180-185
Author(s):  
M. Saleh ◽  
Ferenc Szodrai
Keyword(s):  
Wind Turbine ◽  
Turbine Blade ◽  
Primary Objective ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Energy Potential ◽  
Cross Sectional ◽  
Tip Speed Ratio ◽  
Savonius Wind Turbine ◽  
Cfd Method

Nowadays the importance of renewable energy is growing, and the utilization of the low wind energy potential is getting crucial. There are turbines with low and high tip speed ratio. Turbines with low tip speed ratio such as the Savonius wind turbine can generate adequate amount of torque at low wind velocities. These types of turbines are also called drag machines. The geometry of the blade can greatly influence the efficiency of the device. With Computational Fluid Dynamics (CFD) method, several optimizations can be done before the production. In our paper the Savonius wind turbine blade geometry was based on the so-called Myring equation. The primary objective of this paper was to increase the power coefficient by modelling the effect of the wind on the turbine blade. For the sake of simplicity, a 2D cross-sectional area was investigated in the simulation with ANSYS CFX 19.1.

Numerical Modelling of Savonius Wind Turbine With Downstream Baffle

2015 ◽  
Author(s):  
Ahmed M. El Baz ◽  
Nabil A. Mahmoud ◽  
Ashraf M. Hamed ◽  
Ahmed M. El Kholy
Keyword(s):  
Wind Turbine ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Dynamics Model ◽  
Small Power ◽  
Turbine Performance ◽  
Savonius Wind Turbine ◽  
Driving Torque

The application of small power wind turbines has been widely spreading over the last decade. The vertical axis wind turbine type is one class which is very attractive in this respect. However, due to its lower performance, it has not been extensively used in such application. The objective of the present paper is to investigate methods of Savonius turbine performance improvement. It is suggested to use a downstream baffle to achieve this goal. The baffle position, length and inclination angle are optimized using 2D Computational Fluid Dynamics model. The model is initially validated by comparison to experimental data reported for the Savonius turbine without baffle. The results show that 40–50% improvement in turbine performance can be obtained by using the optimum baffle design, compared to the turbine performance without baffle. The baffle effect is analyzed and results show that its major role is to reduce the pressure on the backside of the advancing blade. This effect enhances the positive driving torque on the advancing blade of the Savonius turbine and thus increases its power coefficient near the optimum tip speed ratio.

scholarly journals An innovative augmentation technique of savonius wind turbine performance

2019 ◽  
Vol 44 (1) ◽  
pp. 93-112 ◽  
Author(s):  
Khaled M Youssef ◽  
Ahmed M El Kholy ◽  
Ashraf M Hamed ◽  
Nabil A Mahmoud ◽  
Ahmed M El Baz ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Peak Power ◽  
Stokes Equations ◽  
Power Coefficient ◽  
Navier Stokes ◽  
Future Application ◽  
Speed Ratio ◽  
Ansys Fluent ◽  
Turbine Performance ◽  
Savonius Wind Turbine

This work presents an innovative technique to enhance the performance of the Savonius wind turbine. The new technique is based on introducing an upstream deflector and downstream baffle. The shape and location of both devices are optimized using a genetic algorithm. The performance of the turbine with the optimized devices is compared with the single Savonius turbine performance. The study employs the finite volume solver (ANSYS-FLUENT) to solve unsteady Reynolds Averaged Navier–Stokes equations and turbulence model equations. The optimized configuration results in much higher power coefficient than the Savonius turbine. The average peak power coefficient using both deflector and baffle is 0.47 compared to 0.24 of the Savonius turbine. The peak power coefficient of the turbine corresponds to a speed ratio close to unity. This improved performance is attributed to the favorable aerodynamic interaction between the turbine and the downstream baffle which accelerates the flow around the rotor and generates larger turning torque. The baffle generates a jet effect on the advancing bucket and accelerates the flow behind the bucket creating a large zone of negative pressure and thereby increases the driving torque. Furthermore, the upstream deflector (also called shield or curtain) produces a shield for the returning bucket of the turbine which diminishes the adverse effect associated with the returning bucket on the aerodynamic torque of the turbine. This remarkable improvement of turbine performance will encourage the future application of the Savonius wind turbine in small power applications of wind energy.

scholarly journals Shrouded wind turbine performance in yawed turbulent flow conditions

2021 ◽  
pp. 0309524X2110360
Author(s):  
Gustavo Richmond-Navarro ◽  
Takanori Uchida ◽  
Williams R. Calderón-Muñoz
Keyword(s):  
Energy Source ◽  
Turbulent Flow ◽  
Wind Turbine ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Flow Conditions ◽  
Tip Speed Ratio ◽  
Turbine Performance ◽  
Yaw Angle ◽  
Turbulent Flow Conditions

Wind turbines represent a growing energy source worldwide. In many cases, operating in turbulent and changing wind direction spots. In this work, we use a wind tunnel to analyze the effect of the turbulence in a wind turbine provided with a Wind Lens flow concentrator, under yaw conditions, for turbulence intensity values of 10% and 15%. Measurements are made of the power coefficient as a function of the Tip Speed Ratio using two types of Wind Lens, CiiB5 and CiiB10, at yaw angles from [Formula: see text] to [Formula: see text]. In general, for the turbine with Wind Lens, an increase of the yaw angle causes a reduction of the power coefficient. If the turbine operates with the CiiB10, the stronger the turbulence, the greater performance is obtained. In conclusion, for the case of turbulent flow and yaw = [Formula: see text] or less, the Wind Lens turbine offers better performance than without the flow concentrator.

Numerical Research on the Characteristics of Lift-Drag Type Vertical Axis Wind Turbine

2012 ◽  
Vol 189 ◽  
pp. 448-452
Author(s):  
Yan Jun Chen ◽  
Guo Qing Wu ◽  
Yang Cao ◽  
Dian Gui Huang ◽  
Qin Wang ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Vertical Axis ◽  
Chord Length ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Tip Speed Ratio ◽  
Middle Range ◽  
Parabolic Form ◽  
Cfd Method

Numerical studies are conducted to research the performance of a kind of lift-drag type vertical axis wind turbine (VAWT) affected by solidity with the CFD method. Moving mesh technique is used to construct the model. The Spalart-Allmaras one equation turbulent model and the implicit coupled algorithm based on pressure are selected to solve the transient equations. In this research, how the tip speed ratio and the solidity of blade affect the power coefficient (Cp) of the small H-VAWT is analyzed. The results indicate that Cp curves exhibit approximate parabolic form with its maximum in the middle range of tip speed ratio. The two-blade wind turbine has the lowest Cp while the three-blade one is more powerful and the four-blade one brings the highest power. With the certain number of blades, there is a best chord length, and too long or too short chord length may reduce the Cp.

scholarly journals 361 Savonius wind turbine with wind concentrator : In case of tip speed ratio>1.0

2005 ◽  
Vol 2005 (0) ◽  
pp. 83-84
Author(s):  
Sheng Zhang ◽  
Takayuki Yaginuma ◽  
Masahiro Mino ◽  
Hiroyuki Ueno ◽  
Susumu Ishii
Keyword(s):  
Wind Turbine ◽  
Speed Ratio ◽  
Tip Speed Ratio ◽  
Savonius Wind Turbine

Effect of Slotted Angle on Savonius Wind Turbine Performance

2021 ◽  
Vol 104 ◽  
pp. 83-88
Author(s):  
Rahmat Wahyudi ◽  
Diniar Mungil Kurniawati ◽  
Alfian Djafar
Keyword(s):  
Wind Energy ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Electrical Energy ◽  
Speed Ratio ◽  
Angle Variation ◽  
Wind Speeds ◽  
Turbine Performance ◽  
Savonius Wind Turbine ◽  
Low Wind Speeds

The potential of wind energy is very abundant but its utilization is still low. The effort to utilize wind energy is to utilize wind energy into electrical energy using wind turbines. Savonius wind turbines have a very simple shape and construction, are inexpensive, and can be used at low wind speeds. This research aims to determine the effect of the slot angle on the slotted blades configuration on the performance produced by Savonius wind turbines. Slot angle variations used are 5o ,10o , and 15o with slotted blades 30% at wind speeds of 2,23 m/s to 4,7 m/s using wind tunnel. The result showed that a small slot angle variation of 5o produced better wind turbine performance compared to a standard blade at low wind speeds and a low tip speed ratio.

Savonius Wind Turbine Performances on Wind Concentrator

2017 ◽  
Vol 8 (1) ◽  
pp. 376
Author(s):  
Dygku. Asmanissa Awg. Osman ◽  
Norzanah Rosmin ◽  
Nor Shahida Hasan ◽  
Baharruddin Ishak ◽  
Aede Hatib Mustaamal@Jamal ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Electrical Power ◽  
Vertical Axis ◽  
Angular Speed ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Air Compressor ◽  
Tip Speed Ratio ◽  
Savonius Wind Turbine ◽  
Air Streams

The air streams from the outlet of an air compressor can be used to generate electricity. For instance, if a micro-sized Vertical-Axis Wind-Turbine (VAWT) is installed towards the airflow, some amount of electricity can be generated before being stored in a battery bank. The research’s objectives are to design, fabricate and analyze the performance of Helical Savonius VAWT blade rotors, which is tested with and without using a wind concentrator. The Helical Savonius VAWT is tested at 0 cm without the concentrator, whereas the blade rotor is tested at concave-blade position when using the concentrator. The blade and the wind concentrator designs were based on the dimensions and the constant airflow of the air compressor. The findings suggested that the blade produced its best performance when tested using wind concentrator at concave-blade position in terms of angular speed (<em>ω</em>), tip speed ratio (<em>TSR</em>) and the generated electrical power (<em>P</em><em><sub>E</sub></em>). The findings concluded that the addition of wind concentrator increases the airflow which then provided better performances on the blades.

Study on Performance and Flow Condition of a Cross-Flow Wind Turbine With a Symmetrical Casing

2011 ◽  
Vol 133 (5) ◽  
Author(s):  
Junichiro Fukutomi ◽  
Toru Shigemitsu ◽  
Hiroki Daito
Keyword(s):  
Wind Turbine ◽  
Rotational Speed ◽  
Flow Condition ◽  
Cross Flow ◽  
Low Noise ◽  
Maximum Power ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Tip Speed Ratio ◽  
The Cross

A cross-flow wind turbine has a high torque coefficient at a low tip speed ratio. Therefore, it is a good candidate for use as a self-starting turbine. Furthermore, it has low noise and excellent stability; therefore, it has attracted attention from the viewpoint of applications as a small wind turbine for an urban district. However, its maximum power coefficient is extremely low (10%) as compared to that of other small wind turbines. Prevailing winds in two directions often blow in urban and coastal regions. Therefore, in order to improve the performance and the flow condition of the cross-flow rotor, a casing suitable for this sort of prevailing wind conditions is designed in this research and the effect of the casing is investigated by experimental and numerical analysis. In the experiment, a wind tunnel with a square discharge is used and main flow velocity is set as 20 m/s. A torque meter, a rotational speed pickup, and a motor are assembled with the same axis as the test wind turbine and the tip speed ratio is changeable by a rotational speed controller. The casing is set around the cross-flow rotor and flow distribution at the rotor inlet and the outlet is measured by a one-hole pitot tube. The maximum power coefficient is obtained as Cpmax = 0.19 with the casing, however Cpmax = 0.098 without the casing. It is clear that the inlet and the outlet flow condition is improved by the casing. In the present paper, in order to improve the performance of a cross-flow wind turbine, a symmetrical casing suitable for prevailing winds in two directions is proposed. Then, the performance and the internal flow condition of the cross-flow wind turbine with the casing are clarified. Furthermore, the influence of the symmetrical casing on performance is discussed and the relation between the flow condition and performance is considered.

Sign in / Sign up

Export Citation Format

Share Document