scholarly journals 507 High Speed, High Productive Tapping by Intelligent Machine Tools : Prevention of tap breakage and improvement productivity by adaptive control

2001 ◽  
Vol 2001.3 (0) ◽  
pp. 147-148
Author(s):  
Yoshinori YAMAOKA ◽  
Akimitsu NAGAE ◽  
Yoshiaki KAKINO ◽  
Tomonori SATO
Keyword(s):  
Adaptive Control ◽  
Machine Tools ◽  
High Speed ◽  
Intelligent Machine

High Speed, High Productive Tapping by Intelligent Machine Tools

2000 ◽  
Vol 2000.2 (0) ◽  
pp. 35-36 ◽  
Author(s):  
Yoshinori YAMAOKA ◽  
Yoshiaki KAKINO ◽  
Yasuhiko SUZUKI
Keyword(s):  
Machine Tools ◽  
High Speed ◽  
Intelligent Machine

Integration of Adaptive Control Functions for Drilling in Intelligent Machine Tools

2000 ◽  
Vol 2000.2 (0) ◽  
pp. 49-50 ◽  
Author(s):  
Makoto FUJISHIMA ◽  
Yoshiaki KAKINO ◽  
Atsushi Matsubara
Keyword(s):  
Adaptive Control ◽  
Machine Tools ◽  
Intelligent Machine ◽  
Control Functions

Discussion—Session III: High speed machine tools for aircraft production

1955 ◽  
Vol 34 (4) ◽  
pp. 224
Author(s):  
F.C. Cooke ◽  
S. Radcliffe ◽  
H.A. Chambers ◽  
C. Bromage ◽  
Menelaus ◽  
...  
Keyword(s):  
Machine Tools ◽  
High Speed ◽  
Discussion Session ◽  
Aircraft Production ◽  
High Speed Machine

Multimode Adaptive Control for Tank Gun Control System Based on Tracking Differentiator

2011 ◽  
Vol 383-390 ◽  
pp. 79-85
Author(s):  
Dong Yuan ◽  
Xiao Jun Ma ◽  
Wei Wei
Keyword(s):  
Adaptive Control ◽  
Control System ◽  
High Speed ◽  
Control Method ◽  
Reference Model ◽  
Gun Control ◽  
Math Model ◽  
Tracking Differentiator ◽  
Switch Control ◽  
Model Reference Adaptive

Aiming at the problems such as switch impulsion, insurmountability for influence caused by nonlinearity in one tank gun control system which adopts double PID controller to realize the multimode switch control between high speed and low speed movement, the system math model is built up; And then, Model Reference Adaptive Control (MRAC) method based on nonroutine reference model is brought in and the adaptive gun controller is designed. Consequently, the compensation of nonlinearity and multimode control are implemented. Furthermore, the Tracking Differentiator (TD) is affiliated to the front of controller in order to restrain the impulsion caused by mode switch. Finally, the validity of control method in this paper is verified by simulation.

Stability of Milling Operations With Asymmetric Cutter Dynamics in Rotating Coordinates

2016 ◽  
Vol 138 (8) ◽  
Author(s):  
Alptunc Comak ◽  
Orkun Ozsahin ◽  
Yusuf Altintas
Keyword(s):  
Time Domain ◽  
Machine Tools ◽  
High Speed ◽  
End Mill ◽  
Spindle Shaft ◽  
Milling Operations ◽  
Stability Model ◽  
Principal Directions ◽  
The Stability ◽  
Rotating Coordinates

High-speed machine tools have parts with both stationary and rotating dynamics. While spindle housing, column, and table have stationary dynamics, rotating parts may have both symmetric (i.e., spindle shaft and tool holder) and asymmetric dynamics (i.e., two-fluted end mill) due to uneven geometry in two principal directions. This paper presents a stability model of dynamic milling operations with combined stationary and rotating dynamics. The stationary modes are superposed to two orthogonal directions in rotating frame by considering the time- and speed-dependent, periodic dynamic milling system. The stability of the system is solved in both frequency and semidiscrete time domain. It is shown that the stability pockets differ significantly when the rotating dynamics of the asymmetric tools are considered. The proposed stability model has been experimentally validated in high-speed milling of an aluminum alloy with a two-fluted, asymmetric helical end mill.

Sign in / Sign up

Export Citation Format

Share Document