scholarly journals Shell-side single-phase flows and heat transfer in shell-and-tube heat exchangers (2nd report, Effects of inlet nozzle diameter on flow patterns and local heat transfer coefficients)

1985 ◽  
Vol 51 (466) ◽  
pp. 2000-2005
Author(s):  
Hitoshi MATSUSHIMA ◽  
Wataru NAKAYAMA ◽  
Takehiko YANAGIDA ◽  
Akio KUDO
Keyword(s):  
Heat Transfer ◽  
Heat Exchangers ◽  
Single Phase ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Flow Patterns ◽  
Transfer Coefficients ◽  
Shell Side ◽  
Heat Transfer Coefficients ◽  
Shell And Tube

Visualization of Convective Boiling Heat Transfer in Single Micro-Conduits With Different Shapes of Cross Sections

2005 ◽  
Author(s):  
Tzu-Hsiang Yen ◽  
Masahiro Shoji ◽  
Fumio Takemura ◽  
Yuji Suzuki ◽  
Nobuhide Kasagi
Keyword(s):  
Heat Transfer ◽  
Flow Pattern ◽  
Cross Sections ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Flow Patterns ◽  
Transfer Coefficients ◽  
Convective Boiling ◽  
Heat Transfer Coefficients ◽  
Square Microchannel

Visualization experiments of convective boiling in transparent single micro conduits with the same hydraulic diameter but different cross sections are carried out with simultaneous measurement of local heat transfer coefficients and pressure losses. Two different cross sections with the same similar hydraulic diameters are applied: A circular microtube of 210μm in diameter and a square microchannel of 214μm × 214μm cross section. ITO/Ag thin film of 100 nm is sputtered on the outer surface of the conduits for the direct joule heating. The convective boiling shows some periodic variation of different flow patterns in both square and circular conduits. These flow patterns include bubbly, plug, slug, annular and capillary flows. The capillary flow pattern is the independent liquid droplets moving in the flow direction and very rarely observed in conventional tubes. The reason of such variation of flow patterns is that confined spaces limit the bubble growth in radial direction. So the nucleation bubble grows in both upstream and downstream and makes the flow pattern varies radically. The square microchannel conduit has more simple flow pattern variation, more nucleation bubbles and larger local heat transfer coefficients at lower vapor quality. It is due to that corners of the square microchannel act as helps nucleation cavities. Corners also promotes the formation of liquid film and the contact line between liquid and wall, which can stabilize the flow field. Local heat transfer coefficients decrease with increasing local vapor qualities. Local heat transfer coefficients increase with increasing boiling number but have their maximum value when boiling number reaches critical value. Such peculiar heat transfer characteristics can also be explained by the visualization results.

Local Heat Transfer Coefficients Under an Axisymmetric, Single-Phase Liquid Jet

1991 ◽  
Vol 113 (1) ◽  
pp. 71-78 ◽  
Author(s):  
J. Stevens ◽  
B. W. Webb
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Local Nusselt Number ◽  
Single Phase ◽  
Radial Distance ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Plate Spacing

The purpose of this investigation was to characterize local heat transfer coefficients for round, single-phase free liquid jets impinging normally against a flat uniform heat flux surface. The problem parameters investigated were jet Reynolds number Re, nozzle-to-plate spacing z, and jet diameter d. A region of near-constant Nusselt number was observed for the region bounded by 0≤r/d≤0.75, where r is the radial distance from the impingement point. The local Nusselt number profiles exhibited a sharp drop for r/d > 0.75, followed by an inflection and a slower decrease there-after. Increasing the nozzle-to-plate spacing generally decreased the heat transfer slightly. The local Nusselt number characteristics were found to be dependent on nozzle diameter. This was explained by the influence of the free-stream velocity gradient on local heat transfer, as predicted in the classical analysis of infinite jet stagnation flow and heat transfer. Correlations for local and average Nusselt numbers reveal an approximate Nusselt number dependence on Re1/3.

Experimental Study and Genetic-Algorithm-Based Correlation on Shell-Side Heat Transfer and Flow Performance of Three Different Types of Shell-and-Tube Heat Exchangers

2006 ◽  
Vol 129 (9) ◽  
pp. 1277-1285 ◽  
Author(s):  
Qiu-wang Wang ◽  
Gong-nan Xie ◽  
Bo-tao Peng ◽  
Min Zeng
Keyword(s):  
Heat Transfer ◽  
Genetic Algorithm ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Heat Exchangers ◽  
Transfer Coefficients ◽  
Shell Side ◽  
Heat Transfer Coefficients ◽  
Friction Factors ◽  
Shell And Tube

The heat transfer and pressure drop of three types of shell-and-tube heat exchangers, one with conventional segmental baffles and the other two with continuous helical baffles, were experimentally measured with water flowing in the tube side and oil flowing in the shell side. The genetic algorithm has been used to determine the coefficients of correlations. It is shown that under the identical mass flow, a heat exchanger with continuous helical baffles offers higher heat transfer coefficients and pressure drop than that of a heat exchanger with segmental baffles, while the shell structure of the side-in-side-out model offers better performance than that of the middle-in-middle-out model. The predicted heat transfer rates and friction factors by means of the genetic algorithm provide a closer fit to experimental data than those determined by regression analysis. The predicted corrections of heat transfer and flow performance in the shell sides may be used in engineering applications and comprehensive study. It is recommended that the genetic algorithm can be used to handle more complicated problems and to obtain the optimal correlations.

Sign in / Sign up

Export Citation Format

Share Document