scholarly journals An Innovative PID Controller in Conjunction with DC Electric Motor for Control of Hybrid Electric Vehicle

Author(s):  
Majid Hussain M ◽  
Zulfiqar A Memon ◽  
M Akmal Chaudhary ◽  
Siddique M
Author(s):  
C. S. Nanda Kumar ◽  
Shankar C. Subramanian

Electric and hybrid vehicles are emerging rapidly in the automotive market as alternatives to the traditional Internal Combustion Engine (ICE) driven vehicles to meet stringent emission standards, environmental and energy concerns. Recently, Electric Vehicles (EVs) and Hybrid Electric Vehicles (HEVs) have been introduced in many countries including India. One configuration of a HEV is the Series Hybrid Electric Vehicle (SHEV). The design and analysis of the drive system of a SHEV under Indian conditions is the focus of this paper. In conventional vehicles, the ICE is the power source that drives the vehicle. The energy from the ICE is distributed to the wheels through the transmission, which is then used to generate the traction force at the tyre-road interface. In a HEV, both the engine and the electric motor provide the energy to drive the vehicle. In a SHEV, the energy generated by the electric motor is transmitted through the transmission to meet the torque demand at the wheels. Based on the driver’s acceleration demand and the state of charge of the battery, the controller manages the ICE, the generator and the battery to supply the required energy to the motor. The motor finally develops the required drive torque to generate the traction force at the wheels to meet the vehicle drive performance requirements like gradeability, acceleration and maximum speed. The objective of this paper is to discuss the design of the drive system of a SHEV. This involves the calculation of the power specifications of the electric motor based on the vehicle drive performance requirements. The equations for performing these calculations are presented. The procedure is then demonstrated by considering a typical Indian commercial vehicle along with its typical vehicle parameter values. A simulation study has also been performed by considering the Indian drive cycle to demonstrate the energy savings obtained by the use of a SHEV.


2014 ◽  
Vol 695 ◽  
pp. 770-773
Author(s):  
Siti Nur Umira Zakaria ◽  
Erwan Sulaiman

Research on hybrid electric vehicle (HEV) which combined battery based electric motor and conventional internal combustion engine (ICE) have been intensively increased since the last decade due to their promising solution that can reduce global warming. Some examples of electric motors designed for HEV propulsion system at present are dc motor, induction motor (IM), interior permanent magnet synchronous motor (IPMSM) and switched reluctance motor (SRM). Although IPMSMs are considered to be one of the successful electric motor used in HEVs, several limitations such as distributed armature windings, un-control permanent magnet (PM) flux and higher rotor mechanical stress should be resolved. In this paper, design improvement of E-Core hybrid excitation flux switching motor (HEFSM) for hybrid electric vehicles (HEVs) applications are presented. With concentrated armature and field excitation coil (FEC) windings, variable flux capability and robust rotor structure, performances of initial and improved 6S-14PE-Core HEFSM are analyzed. The improved topology has achieved highest torque and power of 246.557Nm and 187.302 kW, respectively.


2012 ◽  
Vol 165 ◽  
pp. 73-77
Author(s):  
A.S. Danardono ◽  
Didi Widya Utama ◽  
Gandjar Kiswanto

This research describes the scope of design and test a traction controller to combine a 6.54 kW gasoline engine power and 2x48VDC/0.5 kW electrical brushless motors in a serial-parallel type of small hybrid electric vehicle. A central control system was designed to operate the engine which is equipped with continuous variable transmission and electric motor on rear wheel side in order to select the optimal torque in normal driving condition. The battery charging system draws its energy from the engine using two alternators: 80 Watt built-in alternator and 300 Watt additional alternator which is driven using a power take-off unit. To increase the electric charging capacity, the electric motor is able to operate as a generator during acceleration or deceleration condition (regenerative system). The static preliminary testing shows that the electric motor can generate about 38% of nominal motors power at 730 rpm of wheel rotation.


2004 ◽  
Vol 18 (1) ◽  
pp. 30-36 ◽  
Author(s):  
Kyoungcheol Oh ◽  
Donghyeon Kim ◽  
Talchol Kim ◽  
Chulsoo Kim ◽  
Hyunsoo Kim

Sign in / Sign up

Export Citation Format

Share Document