Fabrication of Ti-6Al-4V thin sheet using wire-EDM and its characterisation

2021 ◽  
Vol 1 (1) ◽  
pp. 1
Author(s):  
S. Ragu Nathan ◽  
Nithin Tom Mathew ◽  
K. Manoj Kumar ◽  
M. Baburaj
Keyword(s):  
Thin Sheet ◽  
Wire Edm

Mechanics of Loading and Deforming of Thin-Sheet Blank at Electro-Hydraulic Forming

2017 ◽  
Vol 11 (5) ◽  
pp. 332
Author(s):  
Viacheslav S. Mamutov ◽  
Gennady N. Zdor
Keyword(s):  
Thin Sheet ◽  
Sheet Blank

Buckling of thin sheet of delaminated plates with repair fasteners

AIAA Journal ◽  
1998 ◽  
Vol 36 ◽  
pp. 2236-2241
Author(s):  
Chien-Chang Lin ◽  
Shou-Hsiung Cheng
Keyword(s):  
Thin Sheet

STUDI OF FRUIT LEATHER PROCESSING OF MANGGO

2013 ◽  
Vol 3 (2) ◽  
pp. 124-132
Author(s):  
Yessy Rosalina ◽  
Laili Susanti ◽  
Tatik Sulasmi
Keyword(s):  
Thin Sheet ◽  
Physical Appearance ◽  
The Other ◽  
Drying Temperature ◽  
Fruit Flesh ◽  
Leather Processing ◽  
High Yielding Varieties ◽  
Processing Techniques

Mango varieties Bengkulu is one of high yielding varieties from Bengkulu Province. The plants grow well and produce fruits almost year-around in all regions in the province of Bengkulu. Mango varieties Bengkulu have very large fruit, thick fruit flesh and slightly sour flavors. It makes Mango varieties Bengkulu is very suitable to be consumed in the form of a processed. Fruit leather is one form of processed fruit. Fruit leather is a thin sheet of fruit in dried form. The results showed that the best processing techniques of fruit leather for mango varieties Bengkulu is the process with addition of sugar by 20% and drying temperature at 60 ?C. The treatment produce fruit leather with the best physical appearance and flavor compared with the other treatments.

Comparability of structured and flat reference specimens made of thin sheet metal

2015 ◽  
Vol 57 (6) ◽  
pp. 567-573 ◽  
Author(s):  
Fedor Kazak ◽  
Sabine Weiß
Keyword(s):  
Sheet Metal ◽  
Thin Sheet ◽  
Thin Sheet Metal ◽  
Reference Specimens

Modeling of Thin Sheet Blanking with a Micromechanical Approach Application of the MTS Model

2002 ◽  
Vol 5 (2-3-4) ◽  
pp. 423-432 ◽  
Author(s):  
Christophe Poizat ◽  
Christophe Husson ◽  
Said Ahzi ◽  
Nadia Bahlouli ◽  
Laurent Merle
Keyword(s):  
Thin Sheet ◽  
Micromechanical Approach

Experimental and Numerical Analysis of Blanking for Thin Sheet Metal Parts

2001 ◽  
Vol 4 (3-4) ◽  
pp. 319-333
Author(s):  
Vincent Lemiale ◽  
Philippe Picart ◽  
Sébastien Meunier
Keyword(s):  
Numerical Analysis ◽  
Sheet Metal ◽  
Thin Sheet ◽  
Metal Parts ◽  
Sheet Metal Parts ◽  
Thin Sheet Metal

Effect of Local Heating on the Mechanical Characteristics of Repaired Automotive Panels

2019 ◽  
Vol 56 (4) ◽  
pp. 750-758
Author(s):  
Nicolae Navodariu ◽  
Mihai Branzei ◽  
Robert Ciocoiu ◽  
Ion Ciuca ◽  
Razvan Coman ◽  
...  
Keyword(s):  
Mechanical Characteristics ◽  
Cold Working ◽  
Local Heating ◽  
Thin Sheet ◽  
Heating Time ◽  
Steel Plates ◽  
Maximum Temperature ◽  
Material Microstructure ◽  
Technology Process ◽  
Automotive Panels

Flame straightening is a technology process used to eliminate deformations. This method relies on local heating of the material to correct geometry or damaged parts. In the local automobile services its main use is for repairs of less critical deformed components. The maximum temperature and thermal gradient, heating time, cooling rate and number of heating cycles affect the mechanical properties since local heating can alter material microstructure. The aim of this research was to determine the mechanical characteristics of thin steel plates repaired by local heating associated with plastic deformation (similar to hot working) and cold straightening (similar to local cold working) for automotive side and door panels made of structural steel. Thin sheet plates, 0.9mm thickness, were deformed by impact and repaired by local heating using the flame and induction heating then plastically deformed while hot as well as straightened without heating. The heat repaired samples were studied by light microscopy to determine microstructure change and samples were tensile tested to determine their mechanical characteristics. Local excessive grain growth generates anisotropy, the assembly behaves as a composite material with regions that show significant plastic deformations while others little or no deformations at al. Without procedures adjusted to each material repairs involving heating are to be avoided, cold working should be employed when replacement is not possible.

Sign in / Sign up

Export Citation Format

Share Document