Testing and finite element modelling of concrete block masonry walls under axial and out-of-plane loading

2021 ◽  
Vol 6 (1) ◽  
pp. 60
Author(s):  
Andrea C. Isfeld ◽  
Anna L. Müller ◽  
Mark Hagel ◽  
Nigel G. Shrive
Keyword(s):  
Finite Element ◽  
Finite Element Modelling ◽  
Concrete Block ◽  
Masonry Walls ◽  
Element Modelling ◽  
Out Of Plane

scholarly journals An explicit finite element modelling method for masonry walls under out-of-plane loading

2016 ◽  
Vol 113 ◽  
pp. 103-120 ◽  
Author(s):  
Sarkar Noor-E-Khuda ◽  
Manicka Dhanasekar ◽  
David P. Thambiratnam
Keyword(s):  
Finite Element ◽  
Finite Element Modelling ◽  
Masonry Walls ◽  
Explicit Finite Element ◽  
Element Modelling ◽  
Modelling Method ◽  
Out Of Plane

Finite element modelling of reinforced masonry walls under axial compression

2021 ◽  
pp. 113594
Author(s):  
Mohammad Asad ◽  
Tatheer Zahra ◽  
Julian Thamboo ◽  
Mengli Song
Keyword(s):  
Finite Element ◽  
Axial Compression ◽  
Finite Element Modelling ◽  
Masonry Walls ◽  
Element Modelling ◽  
Reinforced Masonry

scholarly journals A Study on Finite Element Modelling and Analysis with respect to Experimental Results of Strengthened Unreinforced Masonry Walls With and Without Kevlar-FRP

2021 ◽  
Vol 23 (2) ◽  
pp. 67-77
Author(s):  
Sugeng Wijanto ◽  
Takim Andriono ◽  
Jovita Tanudjaja
Keyword(s):  
Finite Element ◽  
Finite Element Modelling ◽  
Three Dimensional ◽  
Unreinforced Masonry ◽  
Shear Capacity ◽  
Masonry Walls ◽  
Test Results ◽  
Element Modelling ◽  
Laboratory Test Results ◽  
Set Up

Unreinforced masonry (URM) walls, found in most historical buildings in Indonesia, are relatively brittle with wide variety of material properties. The behaviour of URM walls is very complex, especially when subjected to seismic excitation. In this research, a finite element modelling was set up in order to analyse the seismic performance of URM wall experimental test units, with and without strengthening material. The analysis was conducted using SAP2000 computer program. Three dimensional solids and springs as link connectors were assigned to represent the masonry behaviour. This research aims to compare results obtained from the computer analysis and the previously conducted laboratory experiments. The effectiveness of Kevlar fibre material, which was installed on both wall surfaces and modelled as truss element was also investigated. It was found that the failure mechanisms shown by the SAP2000 model was similar to the laboratory test results. The use of Kevlar Fibre as strengthening material was found able to significantly increase the stiffness and shear capacity of the URM wall.

Damage-based finite-element modelling of in-plane loaded masonry walls repaired with FRCM

2021 ◽  
Vol 254 ◽  
pp. 106481
Author(s):  
Jean-Patrick Plassiard ◽  
Ibrahim Alachek ◽  
Olivier Plé
Keyword(s):  
Finite Element ◽  
Finite Element Modelling ◽  
Masonry Walls ◽  
Element Modelling

Initial imperfections and the initiation of wrinkling in finite element modelling of deep drawing

2000 ◽  
Vol 214 (1) ◽  
pp. 63-73 ◽  
Author(s):  
J Hematian ◽  
P M Wild
Keyword(s):  
Finite Element ◽  
Deep Drawing ◽  
Finite Element Modelling ◽  
Annular Plate ◽  
Finite Element Models ◽  
Essential Requirement ◽  
Element Modelling ◽  
Initial Imperfections ◽  
Different Types ◽  
Out Of Plane

The effect of initial imperfections on the initiation of wrinkling in finite element models of deep drawing operations is assessed. Models of an annular plate are subjected to radial in-plane loading and the effects of different types, magnitudes and distributions of imperfections are investigated. A model of a circular plate subjected to out-of-plane loading from a punch and die is similarly investigated and the results are compared with experimental data. It is confirmed that initial imperfections are an essential requirement for the initiation of wrinkling for the case of in-plane loading. Initial imperfections are shown to be unimportant in the initiation of wrinkling for the case of out-of-plane loading.

Finite element modelling of compartment masonry walls in fire

2003 ◽  
Vol 81 (18-19) ◽  
pp. 1923-1930 ◽  
Author(s):  
A Nadjai ◽  
M O’Garra ◽  
F Ali
Keyword(s):  
Finite Element ◽  
Finite Element Modelling ◽  
Masonry Walls ◽  
Element Modelling ◽  
In Fire
Sign in / Sign up

Export Citation Format

Share Document