Characterization of the biomass of a hybrid anaerobic reactor (HAR) with two types of support material during the treatment of the coffee wastewater

Seeding in Fixed Bed anaerobic reactor are infl uenced by several condition such as the growth rate total population of microbial, bacterial adaption to infl uent and the retention ofÂ biomass in reactor. The aim of this observation is to fi nd out the seeding and acclimation process in anaerobic process by using plastic as support material. Seeding and acclimatization process run smoothly can be seen from the increasing of infl uent or substrate and following by the increasing degradation of soluble COD, beside that the decreasing of VSS concentration indicates that microorganism are all ready fi x in support material, therefore reactor can be operated continuously and the acclimatization process can be stopped.Keywords : anaerobic seeding, acclimation anaerobic process

Download Full-text

Influence of Seeding Conditions on Initial Biofilm Development during the Startup of Anaerobic Fluidized Bed Reactors

Water Science & Technology ◽

10.2166/wst.1989.0219 ◽

1989 ◽

Vol 21 (4-5) ◽

pp. 157-165 ◽

Cited By ~ 2

Author(s):

F. Ehlinger ◽

J. M. Audic ◽

G. M. Faup

Keyword(s):

Fluidized Bed ◽

Future Development ◽

Protein Concentration ◽

Specific Activity ◽

Fluidized Bed Reactor ◽

Fluidized Bed Reactors ◽

Support Material ◽

Biofilm Development ◽

Initial Biofilm

The characterization of the biofilm of an anaerobic fluidized-bed reactor was completed under standard conditions. The distribution of the fixed protein concentration depended on the level in the reactor. The protein concentration reached 1520 µg.g−1 of support at the top of the reactor and only 1200 µg.g−1 at the bottom after 504 hours of operation but the specific activity of the biofilm was 33×10−4 µM acetate.h−1.mg−1 proteins at the bottom and only 26×10−4 µM.h−1.mg−1 at the top. The efficiency of a fluidized bed reactor and the composition of the biofilm changed with an increase of the pH from 7 to 8.5 during the seeding of the support material. Future development of the biofilm and the specific activity of the support were affected.

Download Full-text

Additive technology applied to the realization of K-band microwave terminations: reproducibility improvement

International Journal of Microwave and Wireless Technologies ◽

10.1017/s1759078717001404 ◽

2018 ◽

Vol 10 (1) ◽

pp. 3-8

Author(s):

Azar Maalouf ◽

Ronan Gingat ◽

Vincent Laur

Keyword(s):

3D Printing ◽

Frequency Band ◽

Rectangular Waveguide ◽

Three Dimensional ◽

Low Density ◽

Support Material ◽

Additive Technology ◽

3D Printed ◽

K Band

This study examines K-band rectangular waveguide terminations with three-dimensional (3D)-printed loads, and proposes an Asymmetrical Tapered Wedge topology. This geometry shows a good tradeoff between microwave performance and 3D-printing issues (printing directions and support material requirements), thus improving noticeably the reproducibility of the devices. The effect of the density of the 3D-printed load on the reflection parameter of the termination was investigated. Even for a low density, reflection level remained below −27.5 dB between 18 and 26.5 GHz. Reproducibility was demonstrated by the characterization of six loads that were 3D printed under the same conditions. Measurements demonstrate that a maximum reflection parameter level of −33.5 dB can be ensured over the whole frequency band without any post-machining of the 3D-printed devices.

Download Full-text