Generation of ultra-short pulses using the Wilkinson adder

In this work the possibility of increasing the amplitude of ultra-short pulses and formation of a monocycle Gaussian by adding signals from several oscillators was investigated. For this purpose, the ring adders of Wilkinson design were used. The design of which has been chosen due to low losses and high input decoupling. The S-parameters of the adders with different geometrical parameters have been simulated in the frequency band up to 5 GHz. The obtained results coincided with the experimentally measured characteristics. The monopulse amplitude was increased and a bipolar pulse shape was formed by adding ultrashort pulses of equal and different polarities using the adders. This approach allows you to adjust the parameters of the output signal by adjusting the delays of the triggering signals.

Seismic Wave Propagation Characteristics and Their Effects on the Dynamic Response of Layered Rock Sites

To investigate the seismic response of layered rock sites, a multidomain analysis method was proposed. Three finite element models with infinite element boundaries for layered sites were analysed. The results of this multidomain analysis show that stratum properties and elevation have an impact on wave propagation characteristics and the dynamic response of layered sites. Compared with the rock mass, the overlying gravel soil has a greater dynamic amplification effect at the sites. A time domain analysis parameter PGA(IMF) was proposed to analyse the effects of different strata on the seismic magnification effect of layered sites, and its application was also discussed in comparison with PGA. According to the frequency domain analysis, the interface of the rock mass strata has a low impact on the Fourier spectrum characteristics of the sites, but gravel soil has a great magnification effect on the spectrum amplitude in the high-frequency band (≥30 Hz) of waves. Moreover, the stratum properties have a great influence on the shape and peak value of the Hilbert energy and marginal spectrum at layered sites. When waves propagate from hard rock to soft rock, the peak value of the Hilbert energy spectrum changes from single to multiple peaks; then, in gravelly soil, the Hilbert energy spectral peak, its nearby amplitude and the amplitude in the high-frequency band (28–36 Hz) are obviously amplified. The frequency components and amplitude of the marginal spectrum become more abundant and larger from rock to gravelly soil in the high-frequency band (28–35 Hz).

Median line-gram and its application in the fault diagnosis of rolling bearing

The level selection of frequency band division structure relies on previous information in most gram approaches that capture the optimal demodulation frequency band (ODFB). When an improper level is specified in these approaches, the fault characteristic information contained in the produced ODFB may be insufficient. This research proposes a unique approach termed median line-gram (MELgram) to tackle the level selection problem. To divide the frequency domain signal into a series of demodulation frequency bands, a spectrum median line segmentation model based on Akima interpolation is first created. The level and boundary of the segmentation model can be adaptively identified by this means. Second, the acquired frequency bands are quantized using the negative entropy index, and the ODFB is defined as the frequency band with the largest value. Third, the envelope spectrum is used to determine the ODFB characteristic frequency to pinpoint the bearing fault location. Finally, both simulation and experimental signal analysis are used to demonstrate the efficiency of the suggested method. Furthermore, the suggested method extracts more defect feature information from the ODFB than existing methods.

Developing Hybrid Car to Car Communication System Based on MIMO Visible Light and Radio Frequency

This paper combines the advantages of both VLC communication and RF communication for car-to-car applications to achieve a higher data rate, more range coverage, smaller delay, and smaller BER. In the proposed scheme, the VLC maximum communication distance is chosen as 100 m per-hop approximately, which can be extended through multi-hop up to the timeout window of 5 hops. In contrast, the RF maximum communication distance is chosen as 200 m per-hop approximately, which is reasonable at the frequency band of 70 GHz to 90 GHz due to the high attenuation at this frequency band. A MATLAB simulation for a car-to-car framework is built to demonstrate and compare the BER, throughput, and delay outcomes at a hybrid VLC and RF communication. Our results show that VLC can achieve up to four times of the RF throughput while maintaining low BER of 10-6 and small delay of 10-4 with respect to RF communication only.

A compact and miniaturized implantable antenna for ISM band in wireless cardiac pacemaker system

A tiny and compact implantable antenna for wireless cardiac pacemaker systems is designed. The antenna works in the Industrial Scientific Medical (ISM) frequency band (2.4–2.48 GHz). The size of the antenna is greatly reduced with the adoption of a high dielectric constant medium and a folded meander structure. The volume of the antenna is 4.5 mm3, and the size is only 3 mm × 3 mm × 0.5 mm. Based on the literature research, it was found that the design was the smallest among the same type of implanted antenna. The antenna is optimized and loaded with a defective slotted structure, which improves the efficiency of the overall performance of the antenna and thus the gain thereof. The antenna maintains good impedance matching in the ISM frequency band, covering the entire ISM frequency band. The actual bandwidth of the antenna is 22%, with the peak gain of − 24.9 dBi. The antenna is processed and manufactured in such a manner that the simulation keeps consistent with the actual measurement. In addition, the specific absorption rate of the antenna is also evaluated and analyzed. The result shows that this kind of antenna is the best choice to realize the wireless biological telemetry communication in the extremely compact space of the wireless cardiac pacemaker system.

A Reflection-Type Dual-Band Phase Shifter with an Independently Tunable Phase

This paper presents a design for a dual-band tunable phase shifter (PS) with independently controllable phase shifting between each operating frequency band. The proposed PS consists of a 3-dB hybrid coupler, in which the coupled and through ports terminate with the same two reflection loads. Each reflection load consists of a series of quarter-wavelength (λ/4) transmission lines, λ/4 shunt open stubs, and compensation elements at each operating frequency arm. In this design, a wide phase shifting range (PSR) is achievable at each operating frequency band (fL: lower frequency; fH: higher frequency) by compensating for the susceptance occurring at the co-operating frequency band caused by the λ/4 shunt open stub. The load of fL does not affect the load of fH and vice versa. The dual-band tunable PS was fabricated at fL = 1.88 GHz and fH = 2.44 GHz, and testing revealed that achieved a PSR of 114.1° with an in-band phase deviation (PD) of ± 8.43° at fL and a PSR of 114.0° ± 5.409° at fH over a 100 MHz bandwidth. In addition, the maximum insertion losses were smaller than 1.86 dB and 1.89 dB, while return losses were higher than 17.2 dB and 16.7 dB within each respective operating band.