CONJUGATE NATURAL CONVECTION AIR-COOLING OF SUBSTRATE-MOUNTED HEAT SOURCES IN AN ENCLOSURE -EFFECT OF ASPECT RATIO AND BOUNDARY CONDITIONS

1998 ◽  
Author(s):  
P.N. Madhavan ◽  
V.M.K. Sastri
Keyword(s):  
Natural Convection ◽  
Aspect Ratio ◽  
Boundary Conditions ◽  
Air Cooling ◽  
Heat Sources ◽  
Conjugate Natural Convection

Three-Dimensional Steady and Oscillatory Natural Convection in a Rectangular Enclosure With Heat Sources

2016 ◽  
Vol 138 (9) ◽  
Author(s):  
Amin Bouraoui ◽  
Rachid Bessaïh
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Numerical Study ◽  
Three Dimensional ◽  
Air Cooling ◽  
Heat Sources ◽  
Rectangular Enclosure ◽  
Aspect Ratios ◽  
Simpler Algorithm ◽  
Strong Relation

In this paper, a numerical study of three-dimensional (3D) natural convection air-cooling of two identical heat sources, simulating electronic components, mounted in a rectangular enclosure was carried out. The governing equations were solved by using the finite-volume method based on the SIMPLER algorithm. The effects of Rayleigh number Ra, spacing between heat sources d, and aspect ratios Ax in x-direction (horizontal) and Az in z-direction (transversal) of the enclosure on heat transfer were investigated. In steady state, when d is increased, the heat transfer is more important than when the aspect ratios Ax and Az are reduced. In oscillatory state, the critical Rayleigh numbers Racr for different values of spacing between heat sources and their aspect ratios, at which the flow becomes time dependent, were obtained. Results show a strong relation between heat transfers, buoyant flow, and boundary layer. In addition, the heat transfer is more important at the edge of each face of heat sources than at the center region.

Natural Convection Liquid Cooling of a Substrate-Mounted Protrusion in a Square Enclosure: A Parametric Study

1992 ◽  
Vol 114 (2) ◽  
pp. 401-409 ◽  
Author(s):  
S. B. Sathe ◽  
Y. Joshi
Keyword(s):  
Natural Convection ◽  
Boundary Conditions ◽  
Flow Behavior ◽  
Air Cooling ◽  
Square Enclosure ◽  
Simple Boundary ◽  
Wide Range ◽  
Solid Region ◽  
Rayleigh Numbers ◽  
Thermal Conductivities

The coupled conduction and natural convection transport from a substrate-mounted heat generating protrusion in a liquid-filled square enclosure is numerically examined. The governing steady two-dimensional equations are solved using a finite-difference method for a wide range of Rayleigh numbers, protrusion thermal conductivities and widths, substrate heights, and enclosure boundary conditions. The results presented apply to liquids with 10≤Pr≤1000. It was established that in many situations it may be inappropriate to specify simple boundary conditions on the solid surface and decouple the conduction within the substrate or the protrusion. Higher Rayleigh numbers, protrusion thermal conductivities, and widths enhanced cooling. A variation in the substrate height did not affect the maximum protrusion temperature; however, the flow behavior was considerably altered. An empirical correlation for the maximum protrusion temperature was developed for a wide range of parametric values. The enclosure thermal boundary conditions changed the heat transfer in the solid region to only a small extent. Immersion cooling in common dielectric liquids was shown to be advantageous over air cooling only if the thermal conductivity of the protrusion was larger than that of the liquid.

scholarly journals Intensification of Heat Transfer in Cavity Partially Heated and Filled with Nanofluid (Cu-Water)

2015 ◽  
Vol 55 ◽  
pp. 173-179
Author(s):  
Ridha Jmai ◽  
Brahim Ben Beya ◽  
Taieb Lili
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Natural Convection ◽  
Aspect Ratio ◽  
Heat Transfer Rate ◽  
Finite Volume ◽  
Transfer Rate ◽  
Heat Sources ◽  
Flow And Heat Transfer ◽  
Vertical Walls

Natural convection in a rectangular cavity with aspect ratio (Ax), partially heated and filled with a nanofluid (Cu-Water) has been studied numerically. Two heat sources with length (B) are placed on the opposite vertical walls; the remainder of the walls is maintained adiabatic while the horizontal walls are brought to a cold temperature. The equations governing the flow are solved using a finite volume home code using a multigrid technique. Among the parameters governing the flow, a detailed study on the effects of the aspect ratio (Ax) and the length of the source (B) on flow and heat transfer rate is given. The results are shown in terms of streamlines and isotherms. It was found that the transfer of heat significantly increases with the aspect ratio (Ax) and the length of the source (B). A correlation expressing the Nusselt number as a function of (Ax) and d is established.

Sign in / Sign up

Export Citation Format

Share Document