scholarly journals Fluid structure interactions of a pitching wing at high angle of attack

Author(s):  
Gwenael Acher ◽  
Patrick Braud ◽  
Ludovic Chatellier ◽  
Lionel Thomas ◽  
Laurent David

This paper deals with the study of the flow around a pitching wing at high angle of attack. Different pitching amplitudes and frequencies are studied using DIC and LPT measurements. The Fluid Structure Interactions are shown and exhibit that the vortex shedding could be reduced by actuating the wing at specific frequencies.

2019 ◽  
Vol 881 ◽  
pp. 313-364 ◽  
Author(s):  
Casey M. Harwood ◽  
Mario Felli ◽  
Massimo Falchi ◽  
Steven L. Ceccio ◽  
Yin L. Young

Compliant lift-generating surfaces have widespread applications as marine propellers, hydrofoils and control surfaces, and the fluid–structure interactions (FSI) of such systems have important effects upon their performance and stability. Multi-phase flows like cavitation and ventilation alter the hydrodynamic and hydroelastic behaviours of lifting surfaces in ways that are not yet completely understood. This paper describes experiments on one rigid and two flexible variants of a vertical surface-piercing hydrofoil in wetted, ventilating and cavitating conditions. Tests were conducted in a towing tank and a free-surface cavitation channel. This work, which is Part 1 of a two-part series, examines the passive, or flow-induced, fluid–structure interactions of the hydrofoils. Four characteristic flow regimes are described: fully wetted, partially ventilated, partially cavitating and fully ventilated. Hydroelastic coupling is shown to increase the hydrodynamic lift and yawing moments across all four flow regimes by augmenting the effective angle of attack. The effective angle of attack, which was derived using a beam model to account for the effect of spanwise twisting deflections, effectively collapses the hydrodynamic load coefficients for the three hydrofoils. A generalized cavitation parameter, using the effective angle of attack, is used to collapse the lift and moment coefficients for all trials at a single immersed aspect ratio, smoothly bridging the four distinct flow regimes. None of the hydrofoils approached the static divergence condition, which occurs when the hydrodynamic stiffness negates the structural stiffness, but theory and experiments both show that ventilation increases the divergence speed by reducing the hydrodynamic twisting moment about the elastic axis. Coherent vortex shedding from the blunt trailing edge of the hydrofoil causes vortex-induced vibration at an approximately constant Strouhal number of 0.275 (based on the trailing edge thickness), and leads to amplified response at lock-in, when the vortex-shedding frequency approaches one of the resonant modal frequencies of the coupled fluid–structure system.


2021 ◽  
Vol 11 (6) ◽  
pp. 2593
Author(s):  
Yasir Al-Okbi ◽  
Tze Pei Chong ◽  
Oksana Stalnov

Leading edge serration is now a well-established and effective passive control device for the reduction of turbulence–leading edge interaction noise, and for the suppression of boundary layer separation at high angle of attack. It is envisaged that leading edge blowing could produce the same mechanisms as those produced by a serrated leading edge to enhance the aeroacoustics and aerodynamic performances of aerofoil. Aeroacoustically, injection of mass airflow from the leading edge (against the incoming turbulent flow) can be an effective mechanism to decrease the turbulence intensity, and/or alter the stagnation point. According to classical theory on the aerofoil leading edge noise, there is a potential for the leading edge blowing to reduce the level of turbulence–leading edge interaction noise radiation. Aerodynamically, after the mixing between the injected air and the incoming flow, a shear instability is likely to be triggered owing to the different flow directions. The resulting vortical flow will then propagate along the main flow direction across the aerofoil surface. These vortical flows generated indirectly owing to the leading edge blowing could also be effective to mitigate boundary layer separation at high angle of attack. The objectives of this paper are to validate these hypotheses, and combine the serration and blowing together on the leading edge to harvest further improvement on the aeroacoustics and aerodynamic performances. Results presented in this paper strongly indicate that leading edge blowing, which is an active flow control method, can indeed mimic and even enhance the bio-inspired leading edge serration effectively.


Sign in / Sign up

Export Citation Format

Share Document