scholarly journals CRANIOFACIAL STRESS PATTERNS AND DISPLACEMENTS AFTER ACTIVATION OF HYRAX DEVICE: FINITE ELEMENT MODELLING

2017 ◽  
Vol 15 (3) ◽  
pp. 517 ◽  
Author(s):  
Sergei Bosiakov ◽  
Anastasiya Vinokurova ◽  
Andrei Dosta
Keyword(s):  
Finite Element ◽  
Sagittal Plane ◽  
Rapid Maxillary Expansion ◽  
Occlusal Plane ◽  
Orthodontic Appliances ◽  
Maxillary Expansion ◽  
Element Analysis ◽  
Surgical Assistance ◽  
First Case ◽  
Orthodontic Device

Rapid maxillary expansion is employed for the treatment of cross-bite and deficiency of transversal dimension of the maxilla in patients with and without cleft of palate and lip. For this procedure, generally, different orthodontic appliances and devices generating significant transversal forces are used. The aim of this study is the finite-element analysis of stresses and displacements of the skull without palate cleft and the skull with unilateral and bilateral cleft after activation of the Hyrax orthodontic device. Two different constructions of the orthodontic device Hyrax with different positions of the screw relative palate are considered. In the first case, the screw is in the occlusal horizontal plane, and in the other, the screw is located near the palate. Activation of the orthodontic device corresponds to the rotation of the screw on one-quarter turn. It is established that the screw position significantly affects the distributions of stresses in skull and displacements of the cranium without palate cleft and with unilateral or bilateral palate cleft. Stresses in the bone structures of the craniums without cleft and with cleft are transferred from the maxilla to the pterygoid plate and pharyngeal tubercle if the screw displaces from the occlusal plane to the palate. Depending on the construction of the orthodontic appliance, the maxilla halves in the transversal plane are unfolded or the whole skull is entirely rotated in the sagittal plane. The stresses patterns and displacements of the skull with bilateral palate cleft are almost unchanged after activation of the orthodontic devices with different positions of the screw, only magnitudes of stresses and displacements are changed. The obtained results can be used for design of orthodontic appliances with the Hyrax screw, as well as for planning of osteotomies during the surgical assistance of the rapid maxillary expansion.

scholarly journals Comparison of Tooth- and Bone-Borne Appliances on the Stress Distributions and Displacement Patterns in the Facial Skeleton in Surgically Assisted Rapid Maxillary Expansion—A Finite Element Analysis (FEA) Study

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1152
Author(s):  
Rafał Nowak ◽  
Anna Olejnik ◽  
Hanna Gerber ◽  
Roman Frątczak ◽  
Ewa Zawiślak
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Rapid Maxillary Expansion ◽  
Stress Distributions ◽  
Maxillary Expansion ◽  
Facial Skeleton ◽  
Element Analysis ◽  
Maxillary Constriction

The aim of this study was to compare the reduced stresses according to Huber’s hypothesis and the displacement pattern in the region of the facial skeleton using a tooth- or bone-borne appliance in surgically assisted rapid maxillary expansion (SARME). In the current literature, the lack of updated reports about biomechanical effects in bone-borne appliances used in SARME is noticeable. Finite element analysis (FEA) was used for this study. Six facial skeleton models were created, five with various variants of osteotomy and one without osteotomy. Two different appliances for maxillary expansion were used for each model. The three-dimensional (3D) model of the facial skeleton was created on the basis of spiral computed tomography (CT) scans of a 32-year-old patient with maxillary constriction. The finite element model was built using ANSYS 15.0 software, in which the computations were carried out. Stress distributions and displacement values along the 3D axes were found for each osteotomy variant with the expansion of the tooth- and the bone-borne devices at a level of 0.5 mm. The investigation showed that in the case of a full osteotomy of the maxilla, as described by Bell and Epker in 1976, the method of fixing the appliance for maxillary expansion had no impact on the distribution of the reduced stresses according to Huber’s hypothesis in the facial skeleton. In the case of the bone-borne appliance, the load on the teeth, which may lead to periodontal and orthodontic complications, was eliminated. In the case of a full osteotomy of the maxilla, displacements in the buccolingual direction for all the variables of the bone-borne appliance were slightly bigger than for the tooth-borne appliance.

scholarly journals Impact of Osteotomy in Surgically Assisted Rapid Maxillary Expansion Using Tooth-Borne Appliance on the Formation of Stresses and Displacement Patterns in the Facial Skeleton—A Study Using Finite Element Analysis (FEA)

2020 ◽  
Vol 10 (22) ◽  
pp. 8261
Author(s):  
Ewa Zawiślak ◽  
Anna Olejnik ◽  
Roman Frątczak ◽  
Rafał Nowak
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Rapid Maxillary Expansion ◽  
Maxillary Expansion ◽  
Facial Skeleton ◽  
Element Analysis ◽  
Skeleton Model ◽  
Skeletal Malocclusion ◽  
The Finite Element Analysis ◽  
Displacement Patterns

The analysis aimed at studying stresses reduced according to Huber’s hypothesis and displacement patterns at selected sites of the facial skeleton using a tooth-borne appliance in surgically assisted rapid maxillary expansion. Five different variants of osteotomy of the midface and a variant without surgical intervention were compared to determine the best model for making an incision in the maxilla. The finite element analysis (FEA) was used for the study. Five osteotomy variants and a variant without osteotomy were modelled using a tooth-borne appliance on a facial skeleton model of a 23-year-old woman with skeletal malocclusion. The finite element mesh was constructed based on the geometry imported into the ANSYS 15.0 (Swanson Analysis System of USA) software, in which calculations were performed using the finite element analysis. Stress distributions and displacement patterns along the X, Y and Z axes are presented for each osteotomy variant with the expansion of the tooth-borne appliance at a level of 0.5 mm. As a result of the analysis it was found that osteotomy of the palatal suture in conjunction with Le Fort I osteotomy has the biggest impact on the course of maxillary expansion. If no osteotomy is performed, an increase in stresses reduced according to Huber occurs in the entire facial skeleton with a simultaneous absence of maxillary expansion.

scholarly journals Dual-section versus conventional archwire for en-masse retraction of anterior teeth with direct skeletal anchorage: a finite element analysis

2021 ◽  
Vol 21 (1) ◽  
Author(s):  
Ryo Hamanaka ◽  
Daniele Cantarella ◽  
Luca Lombardo ◽  
Lorena Karanxha ◽  
Massimo Del Fabbro ◽  
...  
Keyword(s):  
Finite Element ◽  
Tooth Movement ◽  
Occlusal Plane ◽  
Skeletal Anchorage ◽  
Element Analysis ◽  
Posterior Teeth ◽  
Posterior Portion ◽  
Anterior Teeth ◽  
Retraction Force ◽  
En Masse Retraction

Abstract Background The aim of this study is to compare the biomechanical effects of the conventional 0.019 × 0.025-in stainless steel archwire with the dual-section archwire when en-masse retraction is performed with sliding mechanics and skeletal anchorage. Methods Models of maxillary dentition equipped with the 0.019 × 0.025-in archwire and the dual-section archwire, whose anterior portion is 0.021 × 0.025-in and posterior portion is 0.018 × 0.025-in were constructed. Then, long-term tooth movement during en-masse retraction was simulated using the finite element method. Power arms of 8, 10, 12 and 14 mm length were employed to control anterior torque, and retraction forces of 2 N were applied with a direct skeletal anchorage. Results For achieving bodily movement of the incisors, power arms longer than 14 mm were required for the 0.019 × 0.025-in archwire, while between 8 and 10 mm for the dual-section archwire. The longer the power arms, the greater the counter-clockwise rotation of the occlusal plane was produced. Frictional resistance generated between the archwire and brackets and tubes on the posterior teeth was smaller than 5% of the retraction force of 2 N. Conclusions The use of dual-section archwire might bring some biomechanical advantages as it allows to apply retraction force at a considerable lower height, and with a reduced occlusal plane rotation, compared to the conventional archwire. Clinical studies are needed to confirm the present results.

scholarly journals Characteristics and Dynamics of Full Arch Distalization Using Transpalatal Arches with Midpalatal and Interradicular Miniscrews as Temporary Anchorage Devices: A Preliminary Finite Element Analysis

2020 ◽  
Vol 2020 ◽  
pp. 1-19
Author(s):  
Mashallah Khanehmasjedi ◽  
Sepideh Bagheri ◽  
Vahid Rakhshan ◽  
Mojtaba Hasani
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Orthodontic Appliances ◽  
Element Analysis ◽  
Midpalatal Suture ◽  
Second Molar ◽  
Bodily Movement ◽  
Anterior Teeth ◽  
The Right

Introduction. Miniscrews have proved quite effective in fixed orthodontic treatment. They can be placed in areas like palatal interradicular zones or midpalatal suture. Despite the value of these methods and their ever-increasing use, their characteristics are not assessed before when implanted in palatal interradicular areas or in the midpalatal suture. We aimed to assess, for the first time, the dynamics of full arch distalization using such miniscrews. Methods. A 3D model of maxilla with all permanent dentition was created from a CT scan volume. Tissues were segmented and differentiated. Afterward, miniscrews and appliances were designed, and the whole model was registered within a finite element analysis software by assigning proper mechanical properties to tissues and orthodontic appliances. The full arches were distalized using transpalatal arches with miniscrews as anchorage devices (in two different models). The extents of stresses and patterns of movements of various elements (teeth, miniscrews, appliances, tissues) were estimated. Results and Conclusions. Comparing the two models, it is obvious that in both models, the stress distribution is the highest in the TPA arms and the head of the miniscrew where the spring is connected. In comparison with the displacement in the X-axis, the “mesial in” rotation is seen in the first molar of both models. But there is one exception and that is the “mesial out” rotation of the right second molar. In all measurements, the amount of movement in Model 2 (with palatal interradicular miniscrews) is more than that in Model 1 (with midpalatal miniscrew). In the Y-axis, more tipping is seen in Model 2, especially the anterior teeth (detorque) and the first molar, but in Model 1, bodily movement of the first molar is more evident. Along the Z-axis, the mesial intrusion of the first molar and the distal extrusion of this tooth can be seen in both models. Again, the displacement values are higher in the second model (with interradicular miniscrews). In comparison with micromotion and stress distribution of miniscrews, in Model 1, maximum stress and micromotion is observed at the head of the miniscrew where it is attached to the spring. Of course, this amount of micromotion increases over time. The same is true for Model 2, but with a lower micromotion. As for the amount of stress, the stress distribution in both miniscrews of both models is almost uniform and rather severe.

Sign in / Sign up

Export Citation Format

Share Document