scholarly journals Computer Simulations of Rolling Texture Development in Polycrystalline FCC Metals

1977 ◽  
Vol 41 (6) ◽  
pp. 535-541
Author(s):  
Kazuyoshi Sekine ◽  
Osamu Yoshimura
Keyword(s):  
Computer Simulations ◽  
Rolling Texture ◽  
Texture Development

Slip behavior and its effect on rolling texture development in a dual-phase Mg–Li alloy

2020 ◽  
Vol 813 ◽  
pp. 152117 ◽  
Author(s):  
Fei Guo ◽  
Lei Liu ◽  
Yanlong Ma ◽  
Luyao Jiang ◽  
Yuhe Zhang ◽  
...  
Keyword(s):  
Rolling Texture ◽  
Texture Development ◽  
Dual Phase

Texture Development in a Special Rolled AA6016 Aluminum Alloy

2013 ◽  
Vol 834-836 ◽  
pp. 416-419
Author(s):  
Tong He ◽  
Ning Zhang ◽  
Wei Sun
Keyword(s):  
Aluminum Alloy ◽  
Reference Frame ◽  
Rolling Texture ◽  
Texture Development ◽  
X Ray Diffraction ◽  
Deformation Method ◽  
X Ray ◽  
Cold Rolled

AA6016 aluminum alloy with a strong β fiber rolling texture was cold rolled to different reductions by means of a special deformation method (side rolling in Chinese). The texture development during side rolling was investigated by X-ray diffraction. The typical B, S and C orientation on the β fiber are transformed into the B'{111}, S'{22 17 9} and C'{011} orientations, respectively. The results show that these orientations are unstable and gradually rotate to the B orientation in the new sample reference frame.

scholarly journals Development of Rolling Textures in an Austenitic Stainless Steel

1992 ◽  
Vol 19 (1-2) ◽  
pp. 101-121 ◽  
Author(s):  
C. D. Singh ◽  
V. Ramaswamy ◽  
C. Suryanarayana
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Shear Bands ◽  
Three Dimensional ◽  
Rolling Texture ◽  
Orientation Distribution ◽  
Distribution Functions ◽  
Texture Development ◽  
Slip Planes ◽  
Heterogeneous Deformation

Three dimensional texture analysis by means of orientation distribution functions (ODF) was used to examine the texture development during rolling at 473 K in an austenitic stainless steel. With the help of ODFs results, the different stages of texture development could be assigned to the existing theories of heterogeneous deformation mechanisms of low SFE face-centred cubic metals. The texture at very low degree of rolling consists of two limited orientation tubes with their fibre axes 〈110〉//ND and 〈110〉60∘ND and agrees with the predictions made by Taylor model. With further deformation, twinning causes the reduction of ≈{112}〈111〉 component and leads to the formation of twin {552}〈115〉. Abnormal slip on slip planes parallel to the twin boundaries rotates the twins into the {332}〈113〉 and {111}〈110〉 positions. The shear bands formation in the rotated twin-matrix lamellae changes their orientations near to {011}〈100〉 and {011}〈112〉 positions. Finally, normal slip again continues and sharpens the brass-type rolling texture.

Rolling Texture Development in Cu-Mn-Alloys

1994 ◽  
Vol 157-162 ◽  
pp. 679-684 ◽  
Author(s):  
Olaf Engler ◽  
C. Pithan ◽  
K. Lücke
Keyword(s):  
Rolling Texture ◽  
Texture Development

scholarly journals Rolling texture development in a dual-phase Mg-Li alloy: The role of temperature

2021 ◽  
Author(s):  
Xiaoyan Li ◽  
Fei Guo ◽  
Yanlong Ma ◽  
Luyao Jiang ◽  
Hongliang Lai ◽  
...  
Keyword(s):  
Rolling Texture ◽  
Texture Development ◽  
Dual Phase

THE ROLLING TEXTURE DEVELOPMENT IN AN 8090 Al-Li ALLOY

1987 ◽  
Vol 48 (C3) ◽  
pp. C3-605-C3-611 ◽  
Author(s):  
J. HIRSCH ◽  
O. ENGLER ◽  
K. LÜCKE ◽  
M. PETERS ◽  
K. WELPMANN
Keyword(s):  
Rolling Texture ◽  
Texture Development

Strain rate sensitivity of flow stress and its effect on hot rolling texture development

1993 ◽  
Vol 28 (11) ◽  
pp. 1317-1322 ◽  
Author(s):  
O. Engler ◽  
P. Wagner ◽  
J. Savoie ◽  
D. Ponge ◽  
G. Gottstein
Keyword(s):  
Flow Stress ◽  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Hot Rolling ◽  
Rolling Texture ◽  
Rate Sensitivity ◽  
Texture Development
Sign in / Sign up

Export Citation Format

Share Document