scholarly journals Airfoil optimization for small horizontal axis wind turbine

2021 ◽  
Vol 19 ◽  
pp. 505-510
Author(s):  
Cristhian Leonardo Pabón Rojas ◽  
◽  
Carlos Andrés Trujillo Suarez ◽  
Juan Carlos Serrano Rico ◽  
Elkin Gregorio Flórez Serrano ◽  
...  
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Pitch Angle ◽  
Horizontal Axis ◽  
Middle Zone ◽  
Horizontal Axis Wind Turbine ◽  
Airfoil Optimization ◽  
Low Wind Speed ◽  
Gradient Based ◽  
Blade Element

In order to take advantage of the low wind speed found in the Colombian territory, a gradient-based optimization process (GBA) of 2 airfoils is carried out, using the Xfoil software to evaluate the interactions. The shapes chosen will be destined for the root and for the middle zone of a blade for a small horizontal axis wind turbine (sHAWT). The blade will be created from the calculation of the chord and pitch angle with the blade element momentum methodology (BEM) and the SHAWT will be tested by CFD software to check its performance. As a preliminary result, a root-bound airfoil has been obtained with a higher performance than the airfoil used as a bases.

Design of a Horizontal Axis Wind Turbine for Fiji

2012 ◽  
Author(s):  
Jai N. Goundar ◽  
Sumesh Narayan ◽  
Mohammed Rafiuddin Ahmed
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Rural Areas ◽  
Alternative Energy ◽  
Aerodynamic Characteristics ◽  
Horizontal Axis ◽  
Horizontal Axis Wind Turbine ◽  
Maximum Thickness ◽  
Low Wind Speed ◽  
Bem Theory

The demand and cost of electricity has increased for Pacific Island Countries (PICs). The electricity from main grid does not reach rural areas and outer islands of Fiji. They burn fuel for electricity and daily lighting. Therefore, there is a need to look for alternative energy sources. Wind turbine technology has developed over the past years and is suitable for generating electricity by tapping wind energy. However, turbines designed to operate at higher wind speed do not perform well in Fiji, because Fiji’s average wind velocity is around 5–6 m/s. A 10 m, 3-bladed horizontal axis wind turbine is designed to operate at low wind speed, cut in speed of 3 m/s, cut off speed of 10 m/s and rated wind speed of 6 m/s. The blade sections were designed for different locations along the blade. The airfoil at the tip (AF0914) a has maximum thickness of 14% and maximum camber of 9%; the thickness varies linearly to the root, at the root the airfoil (AF0920) has a maximum thickness of 20% and maximum camber of 9%. The aerodynamic characteristics of airfoil AF0914 were obtained using Xfoil and were validated by experimentation, at turbulence intensities (Tu) of 1% and 3%, and a Reynolds number (Re) of 200,000. The aerodynamic characteristics of other airfoils were also obtained at operating Re at the turbulence intensities of 1% and 3%. These airfoils have good characteristics at low wind speed, and were used to design the 10 m diameter 3-bladed HAWT for Fiji. The turbine has a linear chord distribution for easy manufacturing purpose. Twist distribution was optimized using Blade Element Momentum (BEM) theory, and theoretical power and turbine performance were obtained using BEM theory. At the rated wind speed of 6 m/s and a TSR of 6.5, the theoretical efficiency of the rotor is around 46% and maximum power is 4.4 kW. The turbine has good performance at lower wind speeds and is suitable for Fiji’s conditions.

Optimum Blade Design of Pinwheel Type Horizontal Axis Wind Turbine for Low Wind Speed Areas

2021 ◽  
Author(s):  
Robiul Islam ◽  
Zakia Sultana Snikdha ◽  
Afnan Iffat ◽  
Mhia Md. Zaglul Shahadat
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Horizontal Axis ◽  
Blade Design ◽  
Horizontal Axis Wind Turbine ◽  
Low Wind Speed

scholarly journals Modeling and simulation of forces applied to the horizontal axis wind turbine rotors by the vortex method coupled with the method of the blade element

2021 ◽  
Vol 12 (1) ◽  
pp. 413
Author(s):  
Ibtissem Barkat ◽  
Abdelouahab Benretem ◽  
Fawaz Massouh ◽  
Issam Meghlaoui ◽  
Ahlem Chebel
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Wind Farms ◽  
Vortex Method ◽  
Operating Conditions ◽  
Horizontal Axis ◽  
Rotor Blades ◽  
Good Representation ◽  
Horizontal Axis Wind Turbine ◽  
Blade Element

This article aims to study the forces applied to the rotors of horizontal axis wind turbines. The aerodynamics of a turbine are controlled by the flow around the rotor, or estimate of air charges on the rotor blades under various operating conditions and their relation to the structural dynamics of the rotor are critical for design. One of the major challenges in wind turbine aerodynamics is to predict the forces on the blade as various methods, including blade element moment theory (BEM), the approach that is naturally adapted to the simulation of the aerodynamics of wind turbines and the dynamic and models (CFD) that describes with fidelity the flow around the rotor. In our article we proposed a modeling method and a simulation of the forces applied to the horizontal axis wind rotors turbines using the application of the blade elements method to model the rotor and the vortex method of free wake modeling in order to develop a rotor model, which can be used to study wind farms. This model is intended to speed up the calculation, guaranteeing a good representation of the aerodynamic loads exerted by the wind.

Sign in / Sign up

Export Citation Format

Share Document